A view of the dynamic software product line landscape

Dynamic software product lines extend the concept of conventional SPLs by enabling software-variant generation at runtime. Recent studies yield insights into the current state of the DSPL field, research trends, and major gaps to address.

Dynamic variability in adaptive systems

One of the reasons for using variability in the software product line (SPL) approach (see Apel et al., 2006; Figueiredo et al., 2008; Kastner et al., 2007; Mezini & Ostermann, 2004) is to delay a design decision (Svahnberg et al., 2005). Instead of deciding on what system to develop in advance, with the SPL approach a set of components and a reference architecture are specified and implemented (during domain engineering, see Czarnecki & Eisenecker, 2000) out of which individual systems are composed at a later stage (during application engineering, see Czarnecki & Eisenecker, 2000). By postponing the design decisions in such a manner, it is possible to better fit the resultant system in its intended environment, for instance, to allow selection of the system interaction mode to be made after the customers have purchased particular hardware, such as a PDA vs. a laptop. Such variability is expressed through variation points which are locations in a software-based system where choices are available for defining a specific instance of a system (Svahnberg et al., 2005). Until recently it had sufficed to postpone committing to a specific system instance till before the system runtime. However, in the recent years the use and expectations of software systems in human society has undergone significant changes.Today's software systems need to be always available, highly interactive, and able to continuously adapt according to the varying environment conditions, user characteristics and characteristics of other systems that interact with them. Such systems, called adaptive systems, are expected to be long-lived and able to undertake adaptations with little or no human intervention (Cheng et al., 2009). Therefore, the variability now needs to be present also at system runtime, which leads to the emergence of a new type of system: adaptive systems with dynamic variability.

Product cipher negotiation with on-line evaluation for private communication over computer networks

A method is proposed to offer privacy in computer communications, using symmetric product block ciphers. The security protocol involved a cipher negotiation stage, in which two communicating parties select privately a cipher from a public cipher space. The cipher negotiation process includes an on-line cipher evaluation stage, in which the cryptographic strength of the proposed cipher is estimated. The cryptographic strength of the ciphers is measured by confusion and diffusion. A method is proposed to describe quantitatively these two properties. For the calculation of confusion and diffusion a number of parameters are defined, such as the confusion and diffusion matrices and the marginal diffusion. These parameters involve computationally intensive calculations that are performed off-line, before any communication takes place. Once they are calculated, they are used to obtain estimation equations, which are used for on-line, fast evaluation of the confusion and diffusion of the negotiated cipher. A technique proposed in this thesis describes how to calculate the parameters and how to use the results for fast estimation of confusion and diffusion for any cipher instance within the defined cipher space.

Changes in inositol lipids and phosphates after stimulation of the MAS-transfected NG115-401L-C3 cell line by mitogenic and non-mitogenic stimuli

A neuronal cell line (NG115-401L-C3) was stimulated by mitogenic (angiotensin) and non-mitogenic (bradykinin) peptides and examined for the time course of changes in the levels of radiolabelled inositol phosphates and phospholipids. Both peptides stimulated the time-dependent production of Ins(1,4,5)P3 and related metabolites. Bradykinin caused a much larger increase in Ins(1,4,5)P3 than did angiotensin. However, both peptides stimulated similar rises in the levels of Ins(1,3,4)P3 and InsP4. Bradykinin but not angiotensin, caused a rapid (within 2 s) fall in the levels of PtdIns(4,5)P2 and PtdIns(4)P. Serum pretreatment of the cells caused a 2-3-fold potentiation of both the responses to bradykinin and angiotensin. Although significant levels of PtdIns(3)P were detected in resting cells neither mitogenic (angiotensin, insulin-like growth factor I, transforming growth factor beta) nor non-mitogenic (bradykinin, nerve growth factor interleukin-1) receptor activation changed its levels, arguing against regulation of either PtdIns 3-kinase or PtdIns(3)P phosphatase. We conclude that, as judged by the levels of its product. PtdIns(3)P, the enzyme PtdIns 3-kinase is not activated. This questions the significance of this activity in the receptor-mediated initiation of DNA synthesis.

PCB assembly line assignment:a genetic algorithm approach

Purpose – This paper sets out to study a production-planning problem for printed circuit board (PCB) assembly. A PCB assembly company may have a number of assembly lines for production of several product types in large volume. Design/methodology/approach – Pure integer linear programming models are formulated for assigning the product types to assembly lines, which is the line assignment problem, with the objective of minimizing the total production cost. In this approach, unrealistic assignment, which was suffered by previous researchers, is avoided by incorporating several constraints into the model. In this paper, a genetic algorithm is developed to solve the line assignment problem. Findings – The procedure of the genetic algorithm to the problem and a numerical example for illustrating the models are provided. It is also proved that the algorithm is effective and efficient in dealing with the problem. Originality/value – This paper studies the line assignment problem arising in a PCB manufacturing company in which the production volume is high.

Modelling and benchmarking business processes: The supply-line example

Benchmarking techniques have evolved over the years since Xerox’s pioneering visits to Japan in the late 1970s. The focus of benchmarking has also shifted during this period. By tracing in detail the evolution of benchmarking in one specific area of business activity, supply and distribution management, as seen by the participants in that evolution, creates a picture of a movement from single function, cost-focused, competitive benchmarking, through cross-functional, cross-sectoral, value-oriented benchmarking to process benchmarking. As process efficiency and effectiveness become the primary foci of benchmarking activities, the measurement parameters used to benchmark performance converge with the factors used in business process modelling. The possibility is therefore emerging of modelling business processes and then feeding the models with actual data from benchmarking exercises. This would overcome the most common criticism of benchmarking, namely that it intrinsically lacks the ability to move beyond current best practice. In fact the combined power of modelling and benchmarking may prove to be the basic building block of informed business process re-engineering.

High stability interleaved fibre Michelson interferometer for on-line precision displacement measurements

A self-reference fiber Michelson interferometer measurement system, which employs fiber Bragg gratings (FBGs) as in-fiber reflective mirrors and interleaves together two fiber Michelson interferometers that share the common-interferometric-optical path, is presented. One of the fiber interferometers is used to stabilise the system by the use of an electronic feedback loop to compensate the influences resulting from the environmental disturbances, while the other one is used to perform the measurement task. The influences resulting from the environmental disturbances have been eliminated by the compensating action of the electronic feedback loop, this makes the system suitable for on-line precision measurement. By means of the homodyne phase-tracking technique, the linearity of the measurement results of displacement measurements has been very high.

An investigation of thin amorphous carbon-based sputtered coatings for MEMS and micro-engineering applications

The work presented in this thesis describes an investigation into the production and properties of thin amorphous C films, with and without Cr doping, as a low wear / friction coating applicable to MEMS and other micro- and nano-engineering applications. Firstly, an assessment was made of the available testing techniques. Secondly, the optimised test methods were applied to a series of sputtered films of thickness 10 - 2000 nm in order to: (i) investigate the effect of thickness on the properties of coatingslcoating process (ii) investigate fundamental tribology at the nano-scale and (iii) provide a starting point for nanotribological coating optimisation at ultra low thickness. The use of XPS was investigated for the determination of Sp3/Sp2 carbon bonding. Under C 1s peak analysis, significant errors were identified and this was attributed to the absence of sufficient instrument resolution to guide the component peak structure (even with a high resolution instrument). A simple peak width analysis and correlation work with C KLL D value confirmed the errors. The use of XPS for Sp3/Sp2 was therefore limited to initial tentative estimations. Nanoindentation was shown to provide consistent hardness and reduced modulus results with depth (to < 7nm) when replicate data was suitably statistically processed. No significant pile-up or cracking of the films was identified under nanoindentation. Nanowear experimentation by multiple nanoscratching provided some useful information, however the conditions of test were very different to those expect for MEMS and micro- / nano-engineering systems. A novel 'sample oscillated nanoindentation' system was developed for testing nanowear under more relevant conditions. The films were produced in an industrial production coating line. In order to maximise the available information and to take account of uncontrolled process variation a statistical design of experiment procedure was used to investigate the effect of four key process control parameters. Cr doping was the most significant control parameter at all thicknesses tested and produced a softening effect and thus increased nanowear. Substrate bias voltage was also a significant parameter and produced hardening and a wear reducing effect at all thicknesses tested. The use of a Cr adhesion layer produced beneficial results at 150 nm thickness, but was ineffective at 50 nm. Argon flow to the coating chamber produced a complex effect. All effects reduced significantly with reducing film thickness. Classic fretting wear was produced at low amplitude under nanowear testing. Reciprocating sliding was produced at higher amplitude which generated three body abrasive wear and this was generally consistent with the Archard model. Specific wear rates were very low (typically 10-16 - 10-18 m3N-1m-1). Wear rates reduced exponentially with reduced film thickness and below (approx.) 20 nm, thickness was identified as the most important control of wear.

A rationale for the optimisation by computer methods of the efficient use of metals and materials

The aim of the research project was to gain d complete and accurate accounting of the needs and deficiencies of materials selection and design data, with particular attention given to the feasibility of a computerised materials selection system that would include application analysis, property data and screening techniques. The project also investigates and integrates the three major aspects of materials resources, materials selection and materials recycling. Consideration of the materials resource base suggests that, though our discovery potential has increased, geologic availability is the ultimate determinant and several metals may well become scarce at the same time, thus compounding the problem of substitution. With around 2- to 20- million units of engineering materials data, the use of a computer is the only logical answer for scientific selection of materials. The system developed at Aston is used for data storage, mathematical computation and output. The system enables programs to be run in batch and interactive (on-line) mode. The program with modification can also handle such variables as quantity of mineral resources, energy cost of materials and depletion and utilisation rates of strateqic materials. The work also carries out an in-depth study of copper recycling in the U.K. and concludes that, somewhere in the region of 2 million tonnes of copper is missing from the recycling cycle. It also sets out guidelines on product design and conservation policies from the recyclability point of view.

Rationalisation and improvement of a company's engineering design procedures

There is a great deal of literature about the initial stages of innovative design. This is the process whereby a completely new product is conceived, invented and developed. In industry, however, the continuing success of a company is more often achieved by improving or developing existing designs to maintain their marketability. Unfortunately, this process of design by evolution is less well documented. This thesis reports the way in which this process was improved for the sponsoring company. The improvements were achieved by implementing a new form of computer aided design (C.A.D.) system. The advent of this system enabled the company to both shorten the design and development time and also to review the principles underlying the existing design procedures. C.A.D. was a new venture for the company and care had to be taken to ensure that the new procedures were compatible with the existing design office environment. In particular, they had to be acceptable to the design office staff. The C.A.D. system produced guides the designer from the draft specification to the first prototype layout. The computer presents the consequences of the designer's decisions clearly and fully, often by producing charts and sketches. The C.A.D. system and the necessary peripheral facilities were implemented, monitored and maintained. The system structure was left sufficiently flexible for maintenance to be undertaken quickly and effectively. The problems encountered during implementation are well documented in this thesis.

Beyond theory:an examination of lean new product introduction practices in the UK

Interest is growing around the application of lean techniques to new product introduction (NPI). Although a relatively emergent topic compared with the application of ‘lean’ within the factory, since 2000 there has been an exponential rise in the literature on this subject. However, much of this work focuses on describing and extolling the virtues of the ‘Toyota approach’ to design. Therefore, by way of a stock take for the UK, the present authors' research has set out to understand how well lean product design practices have been adopted by leading manufacturers. This has been achieved by carrying out in-depth case studies with three carefully selected manufacturers of complex engineered products. This paper describes these studies, the detailed results and subsequent findings, and concludes that both the awareness and adoption of practices is generally embryonic and far removed from the theory advocated in the literature.

State-of-the-art in product-service systems

A Product-Service System (PSS) is an integrated combination of products and services. This Western concept embraces a service-led competitive strategy, environmental sustainability, and the basis to differentiate from competitors who simply offer lower priced products. This paper aims to report the state-of-the-art of PSS research by presenting a clinical review of literature currently available on this topic. The literature is classified and the major outcomes of each study are addressed and analysed. On this basis, this paper defines the PSS concept, reports on its origin and features, gives examples of applications along with potential benefits and barriers to adoption, summarizes available tools and methodologies, and identifies future research challenges.

Realising competitive advantage:bicycle manufacture - manufacturing engineering and management

Students at Cranfield Manufacturing Systems Centre helped Brompton Bikes formulate a strategy to meet rapid sales growth. The students took up Operations Excellence MSc, a two-year part-time programme based on the Cranfield MSc in Engineering and Management of Manufacturing Systems, include the Realising Competitive Manufacture module, which is set out to consolidate and embed the knowledge and skills developed throughout the two-year programme. Guided by StratNav process, the students analysed the product families of Brompton, established the basis on which they compete in the market place, and then benchmarked against key competitors. The top five developments identified to be needed by Brompton are: the formation of group technology cells, creation of a robotic brazing facility, and training and recruitment initiatives for production staff.

State-of-the-art in lean design engineering:a literature review on white collar lean

Lean is usually associated with the ‘operations’ of a manufacturing enterprise; however, there is a growing awareness that these principles may be transferred readily to other functions and sectors. The application to knowledge-based activities such as engineering design is of particular relevance to UK plc. Hence, the purpose of this study has been to establish the state-of-the-art, in terms of the adoption of Lean in new product development, by carrying out a systematic review of the literature. The authors' findings confirm the view that Lean can be applied beneficially away from the factory; that an understanding and definition of value is key to success; that a set-based (or Toyota methodology) approach to design is favoured together with the strong leadership of a chief engineer; and that the successful implementation requires organization-wide changes to systems, practices, and behaviour. On this basis it is felt that this review paper provides a useful platform for further research in this topic.