Marine Le Pen and the 'New' FN:a change of style or of substance?

The electoral challenge of the far right is an enduringly problematic feature of contemporary French politics. In the first rounds of the 2012 presidential and parliamentary elections, the Front National (FN) under new leader Marine Le Pen attracted a combined total of ten million votes, bringing its ultra-nationalist policies to the centre of national political debate. This article examines the FN's impact on these elections and its implications for French politics. Drawing on official FN programmes, detailed election results and a range of opinion polling data, it assesses the strength of support for Le Pen and her party and seeks to explain their electoral appeal. In particular, it subjects to analysis the claim that the new leader has ‘de-demonised’ the FN, transforming it from perennial outsider to normal participant in mainstream French politics; and it reflects on the strategic dilemma posed for the centre-right by this newly invigorated far-right challenge.

An investigation of the mechanics of wire drawing with the superposition of an oscillatory drawing stress

A number of investigators have studied the application of oscillatory energy to a metal undergoing plastic deformation. Their results have shown that oscillatory stresses reduce both the stress required to initiate plastic deformation and the friction forces between the tool and workpiece. The first two sections in this thesis discuss historically and technically the devolopment of the use of oscillatory energy techniques to aid metal forming with particular reference to wire drawing. The remainder of the thesis discusses the research undertaken to study the effect of applying longitudinal oscillations to wire drawing. Oscillations were supplied from an electric hydraulic vibrator at frequencies in the range 25 to 500 c/s., and drawing tests were performed at drawing speeds up to 50 ft/m. on a 2000 lbf. bull-block. Equipment was designed to measure the drawing force, drawing torque, amplitude of die and drum oscillation and drawing speed. Reasons are given for selecting mild steel, pure and hard aluminium, stainless steel and hard copper as the materials to be drawn, and the experimental procedure and calibration of measuring equipment arc described. Results show that when oscillatory stresses are applied at frequencies within the range investigated : (a) There is no reduction in the maximum drawing load. (b) Using sodium stearate lubricant there is a negligible reduction in the coefficient of friction between the die and wire. (c) Pure aluminium does not absorb sufficient oscillatory energy to ease the movement of dislocations. (d) Hard aluminium is not softened by oscillatory energy accelerating the diffusion process. (e) Hard copper is not cyclically softened. A vibration analysis of the bull-block and wire showed that oscillatory drawiing in this frequency range, is a mechanical process of straining; and unstraining the drawn wire, and is dependent upon the stiffness of the material being drawn and the drawing machine. Directions which further work should take are suggested.

Managing from the inside out:drawing on 'receptivity' to explain variation in strategy implementation

With the rise of 'New Public Management' (NPM), government policy has encouraged public-sector organizations to downsize and outsource their services. There is, however, local variation in the use of outsourcing - this is 'managing from the inside out'. This paper draws on the notion of receptivity for organizational change to explain variation in strategy implementation. Four receptivity factors are identified which seem to explain the success of two contrasting English local government outsourcing strategies: ideological vision, leading change, institutional politics and implementation capacity. The organization level of change is interconnected with two other levels of change (the public service and environment levels) to illustrate the dynamic nature of change.

Microscale mesoarrays created by dip-pen nanolithography for screening of protein-protein interactions

Using microarrays to probe protein-protein interactions is becoming increasingly attractive due to their compatibility with highly sensitive detection techniques, selectivity of interaction, robustness and capacity for examining multiple proteins simultaneously. The major drawback to using this approach is the relatively large volumes and high concentrations necessary. Reducing the protein array spot size should allow for smaller volumes and lower concentrations to be used as well as opening the way for combination with more sensitive detection technologies. Dip-Pen Nanolithography (DPN) is a recently developed technique for structure creation on the nano to microscale with the capacity to create biological architectures. Here we describe the creation of miniaturised microarrays, 'mesoarrays', using DPN with protein spots 400× smaller by area compared to conventional microarrays. The mesoarrays were then used to probe the ERK2-KSR binding event of the Ras/Raf/MEK/ERK signalling pathway at a physical scale below that previously reported. Whilst the overall assay efficiency was determined to be low, the mesoarrays could detect KSR binding to ERK2 repeatedly and with low non-specific binding. This study serves as a first step towards an approach that can be used for analysis of proteins at a concentration level comparable to that found in the cellular environment.

The extreme right in France:from Pétain to Le Pen

The Front National has for some years been France's third political party and the most notable far-right force in Europe; its leader, Jean-Marie Le Pen, contested the 2002 presidential election run-off with 5.5 million votes. What do Le Pen and the FN represent? What are their historical roots, their values and their policies? Who votes for them and why? And what has been their impact on the political agenda in France? Adopting an essentially chronological approach, the book traces the political lineage of Le Pen and the FN through key figures, movements and events on the French extreme right from the Vichy regime to the present, providing a detailed historical perspective for understanding the FN today. Part I provides a historical study of the extreme right in France since 1940, examining • the Vichy regime, collaboration and ‘collaborationism’, • the aftermath of Liberation and the post-war extreme right, • the Poujadist movement and the politics of populism, • the Algerian War as a catalyst for change, • the ‘Nouvelle Droite’ and the search for doctrinal renewal, • old and new forms of extreme-right ideology and activism. Part II undertakes a comprehensive study of the FN, analysing • the party’s early development and electoral rise, • its evolving programme and strategy, • the factors underlying its popular appeal, • the geography and composition of its electorate, • its exercise of local power and regional influence, • and its defining impact on the national political agenda. The FN, it is argued, represents both the latest manifestation of a long tradition of authoritarian nationalism and a complex new phenomenon within the changing social and political dynamics of contemporary France.

The Mechanics of the drawing of polygonal sections from round at elevated temperature

Economic factors such as the rise in cost of raw materials, labour and power, are compelling manufacturers of cold-drawn polygonal sections, to seek new production routes which will enable the expansion in the varieties of metals used and the inclusion of difficult-to-draw materials. One such method generating considerable industrial interest is the drawing of polygonal sections from round at elevated temperature. The technique of drawing mild steel, medium carbon steel and boron steel wire into octagonal, hexagonal and square sections from round at up to 850 deg C and 50% reduction of area in one pass has been established. The main objective was to provide a basic understanding of the process, with particular emphasis being placed on modelling using both experimental and theoretical considerations. Elevated temperature stress-strain data was obtained using a modified torsion testing machine. Data were used in the upper bound solution derived and solved numerically to predict drawing stress strain, strain-rate, temperature and flow stress distribution in the deforming zone for a range of variables. The success of this warm working process will, of course, depend on the use of a satisfactory elevated temperature lubricant, an efficient cooling system, a suitable tool material having good wear and thermal shock resistance and an efficient die profile design which incorporates the principle of least work. The merits and demerits of die materials such as tungsten carbide, chromium carbide, Syalon and Stellite are discussed, principally from the standpoint of minimising drawing force and die wear. Generally, the experimental and theoretical results were in good agreement, the drawing stress could be predicted within close limits and the process proved to be technically feasible. Finite element analysis has been carried out on the various die geometries and die materials, to gain a greater understanding of the behaviour of these dies under the process of elevated temperature drawing, and to establish the temperature distribution and thermal distortion in the deforming zone, thus establishing the optimum die design and die material for the process. It is now possible to predict, for the materials already tested, (i) the optimum drawing temperature range, (ii) the maximum possible reduction of area per pass, (iii) the optimum drawing die profiles and die materials, (iv) the most efficient lubricant in terms of reducing the drawing force and die wear.