Studies in clay chemistry

A study of clay chemistry has been approached with three aims: - to modify the conducting properties by intercalation of tetrathiafulvalene, - to study the electrochemistry of redox-active coordination compounds immobilised on clay coated electrodes, and - to study the role of clays as reagents in inorganic glass forming reactions using mainly solid-state magic-angle-spinning NMR. TTF was intercalated by smectites containing different interlayer and lattice cations. Evidence from ESR and 57Fe Mossbauer indicated charge-transfer from TTF to structural iron in natural montmorillonite, and to interlayer Cu2+ in Cu2+ exchanged laponite. No charge transfer was observed for laponite (Na+ form) itself. Ion exchange of TTF3(BF4)2 with laponite was found to proceed quantitatively. The intercalated species were believed to be (TTF)2+ dimers. Conductivity data showed an order of magnitude increase for the intercalated clays. The mechanism is thought to be ionic rather than CT as Na+ laponite showed a similar enhancement in conductivity. Mechanically robust colloidal clay films were prepared on platinum electrodes. After immersion in solutions containing redox active complexes [Co(bpy)3]3+ and [Cr(bpy)3]3+, the films became electroactive when a potential was applied. Cyclic voltammograms obtained for both complexes were found to be of the diffusion controlled type. For [Co(bpy)3]3+ immobilised on clay coated electrodes, a one-step oxidation and four-step reduction wave was observed corresponding to a one electron stepwise reversible reduction of Co(III), through Co(II), Co(I), Co(O) to Co(I) oxidation state. For [Cr(bpy)3]3+ the electrochemistry was complicated by the presence of additional waves corresponding to the dissociation of [Cr(bpy)3]3+ into the diaquo complex. ESR and diffuse reflectance data supported such a mechanism. 29Si, 27Al and 23Na MAS NMR spectroscopy, supported by powder XRD and FTIR, was used to probe the role of clays as reagents in glass forming reactions. 29Si MAS NMR was found to be a very sensitive technique for identifying the presence and relative abundance of crystalline and non-crystalline phases. In thermal reactions of laponite formation of new mineral phases such as forsterite, akermanite, sillimanite and diopside were detected. The relative abundance of each phase was dependent on thermal history, chemical nature and concentration of the modifier oxide present. In continuing work, the effect of selected oxides on the glass forming reactions of a model feldspar composition was investigated using solid state NMR alone. Addition of network modifying oxides generally produced less negative 29Si chemical shifts and larger linewidths corresponding to a wider distribution of Si-O-Si bond angles and lengths, and a dominant aluminosilicate phase with a less polymerised structure than the starting material. 29Si linewidths and 27Al chemical shifts were respectively correlated with cationic potential and Lewis acidity of the oxide cations. Anomalous Al(4) chemical shifts were thought to be due to precipitation of aluminate phases rather than a breakdown in Lowenstein's aluminium avoidance principle.

Capacity of the upstart algorithm

The storage capacity of multilayer networks with overlapping receptive fields is investigated for a constructive algorithm within a one-step replica symmetry breaking (RSB) treatment. We find that the storage capacity increases logarithmically with the number of hidden units K without saturating the Mitchison-Durbin bound. The slope of the logarithmic increase decays exponentionally with the stability with which the patterns have been stored.

Threshold-induced phase transitions in perceptrons

Error rates of a Boolean perceptron with threshold and either spherical or Ising constraint on the weight vector are calculated for storing patterns from biased input and output distributions derived within a one-step replica symmetry breaking (RSB) treatment. For unbiased output distribution and non-zero stability of the patterns, we find a critical load, α p, above which two solutions to the saddlepoint equations appear; one with higher free energy and zero threshold and a dominant solution with non-zero threshold. We examine this second-order phase transition and the dependence of α p on the required pattern stability, κ, for both one-step RSB and replica symmetry (RS) in the spherical case and for one-step RSB in the Ising case.

Finite-connectivity spin-glass phase diagrams and low-density parity check codes

We obtain phase diagrams of regular and irregular finite-connectivity spin glasses. Contact is first established between properties of the phase diagram and the performance of low-density parity check (LDPC) codes within the replica symmetric (RS) ansatz. We then study the location of the dynamical and critical transition points of these systems within the one step replica symmetry breaking theory (RSB), extending similar calculations that have been performed in the past for the Bethe spin-glass problem. We observe that the location of the dynamical transition line does change within the RSB theory, in comparison with the results obtained in the RS case. For LDPC decoding of messages transmitted over the binary erasure channel we find, at zero temperature and rate R=14, an RS critical transition point at pc 0.67 while the critical RSB transition point is located at pc 0.7450±0.0050, to be compared with the corresponding Shannon bound 1-R. For the binary symmetric channel we show that the low temperature reentrant behavior of the dynamical transition line, observed within the RS ansatz, changes its location when the RSB ansatz is employed; the dynamical transition point occurs at higher values of the channel noise. Possible practical implications to improve the performance of the state-of-the-art error correcting codes are discussed. © 2006 The American Physical Society.

Creating demand for better health by using social marketing techniques

The most significant environmental change to support people who want to give up smoking is the legislation to ban smoking in public places. Following Scotland in March 2006, and Wales and Northern Ireland in April 2007, England moves one step closer to being smoke free on 1 July 2007, when it becomes illegal to smoke in almost every enclosed public place and workplace. Social marketing will be used to support this health promoting policy and will become more prominent in the design of health promotion campaigns of the future. Social marketing is not a new approach to promoting health but its adoption by the Government does represent a paradigm shift in the challenge to change public opinion and social norms. As a result some behaviours, like smoking or excessive alcohol consumption, will no longer be socially acceptable. The Department of Health has decided that social marketing should be used in England to guide all future health promotion efforts directed at achieving behavioural goals. This paradigm shift was announced in Chapter 2 of the “Choosing health” White Paper with its emphasis on the consumer, noting that a wide range of lifestyle choices are marketed to people, although health as a commodity itself has not been marketed. The DoH has an internal social marketing development unit to integrate social marketing principles into its work and ensure that providers deliver. The National Centre for Social Marketing has funding to provide ongoing support, to build capacity and capability in the workforce. This article describes the distinguishing features of the social marketing approach. It seeks to answer some questions. Is this really a new idea, a paradigm shift, or simply a change in terminology? What do the marketing principles offer that is new, or are they merely familiar ideas repackaged in marketing jargon? Will these principles be more effective than current health promotion practice and, if so, how does it work? Finally, what are the implications for community pharmacy?

Evolving approaches to sovereignty in the French Pacific

This contribution explores notions of sovereignty in the three French territories of the South Pacific: French Polynesia, New Caledonia, and Wallis and Futuna. It also analyses the key nuances and challenges of the transition from aspirations of 'independence' to those of 'shared sovereignty'. From protectorates or colonies to overseas territories (Territoires d'Outre-Mer), these three territories have experienced specific and customised statuses with various degrees of autonomy, all underscoring a fine line between autonomy and sovereignty. Indeed, 'sovereignty' has today become much more synonymous with the concept of 'self-government' or 'large autonomy', as the current situation in French Polynesia demonstrates. Meanwhile, New Caledonia is one step closer to 'full sovereignty', since its actual status includes provisions for a referendum on self-determination between 2014 and 2018. The claim for independence, a characteristic of Kanak and Maohi movements, has become more pragmatically focused, to the extent that considering sovereignty 'in free-association' with France is now a perfectly conceivable option. © 2012 Copyright Taylor and Francis Group, LLC.

Virtual Gires-Tournois etalons realized with phase-modulated wideband chirped fiber gratings

We propose and demonstrate novel virtual Gires–Tournois (GT) etalons based on fiber gratings. By introducing an additional phase modulation in wideband linearly chirped fiber Bragg gratings, we have successfully generated GT resonance with only one grating. This technique can simplify the fabrication procedure while retaining the normal advantages of distributed etalons, including their full compatibility with optical fiber, low insertion loss, and low cost. Such etalons can be used as dispersion compensation devices in optical transmission systems.

Clustering strategies for object databases

When object databases arrived on the scene some ten years ago, they provided database capabilities for previously neglected, complex applications, such as CAD, but were burdened with one inherent teething problem, poor performance. Physical database design is one tool that can provide performance improvements and it is the general area of concern for this thesis. Clustering is one fruitful design technique which can provide improvements in performance. However, clustering in object databases has not been explored in depth and so has not been truly exploited. Further, clustering, although a physical concern, can be determined from the logical model. The object model is richer than previous models, notably the relational model, and so it is anticipated that the opportunities with respect to clustering are greater. This thesis provides a thorough analysis of object clustering strategies with a view to highlighting any links between the object logical and physical model and improving performance. This is achieved by considering all possible types of object logical model construct and the implementation of those constructs in terms of theoretical clusterings strategies to produce actual clustering arrangements. This analysis results in a greater understanding of object clustering strategies, aiding designers in the development process and providing some valuable rules of thumb to support the design process.

Inference by replication in densely connected systems

An efficient Bayesian inference method for problems that can be mapped onto dense graphs is presented. The approach is based on message passing where messages are averaged over a large number of replicated variable systems exposed to the same evidential nodes. An assumption about the symmetry of the solutions is required for carrying out the averages; here we extend the previous derivation based on a replica-symmetric- (RS)-like structure to include a more complex one-step replica-symmetry-breaking-like (1RSB-like) ansatz. To demonstrate the potential of the approach it is employed for studying critical properties of the Ising linear perceptron and for multiuser detection in code division multiple access (CDMA) under different noise models. Results obtained under the RS assumption in the noncritical regime give rise to a highly efficient signal detection algorithm in the context of CDMA; while in the critical regime one observes a first-order transition line that ends in a continuous phase transition point. Finite size effects are also observed. While the 1RSB ansatz is not required for the original problems, it was applied to the CDMA signal detection problem with a more complex noise model that exhibits RSB behavior, resulting in an improvement in performance. © 2007 The American Physical Society.

Compatibilisation and stabilisation of immiscible polymer blends by reactive processing

The main objectives of this research were to develop optimised chemical compositions and reactive processing conditions for grafting a functional monomer maleic anhydride (MA) in polypropylene (PP), ethylene propylene diene monomer (EPDM) and mixtures of PP-EPDM, and to optimise synthetic routes for production of PP/EPDM copolymers for the purpose of compatibilisation of PP/EPDM blends. The MA-functionalisation was achieved using an internal mixer in the presence of low concentrations (less than 0.01 molar ratio) of a free radical initiator. Various methods were used to purify MA-functionalised PP and the grafting yield was determined using either FTIR or titrametry. The grafting yield of MA alone, which due to its low free-radical reactivity towards polymer macroradicals, was accompanied by severe degradation in the case of PP and crosslinking for EPDM. In the case of MA-functionalised PP/EPDM, both degradation and crosslinking occurred though not to a great extent. The use of tri-functional coagents e.g. trimethylopropane triacrylates (TRIS) with MA, led to high improvement of the grafting yield of MA on the polymers. This is almost certainly due to high free-radical activity of TRIS leading to copolymerisation of MA and TRIS which was followed by grafting of the copolymer onto the polymer backbone. In the case of PP, the use of coagent was also found to reduce the polymer degradation. PP/EPDM copolymers with optimum tensile properties were synthesised using a 'one-step' continues reactive processing procedure. This was achieved firstly by functionalisation of a mixture of PP (higher w/w ratio) and EPDM (low w/w ratio) with MA, in the presence of the coagent TRIS and a small concentration of a free radical initiator. This was then followed by an imidisation reaction with the interlinking agent hexamethylene diamine (HEMDA). Small amount of copolymers, up to 5 phr, which were interlinked with up to 15 phr of HEMDA, were sufficient to compatibilise PP/EPDM75/25 blends resulting in excellent tensile properties compared to binary PP/EPDM 75/25 blend. Improvement in blend's compatibility and phases-stabilisation (observed through tensile and SEM analysis) was shown in all cases with significant interphases adhesion improvement between PP and EPDM, and reduction in domain size across the fractured surface indicating efficient distribution of the compatibiliser.

Alternative Emanzipationsvorstellungen in der DDR unter Honecker (1971-1990):ein Diskussionsbeitrag zur Rollen der Frau

Over the last twenty years the situation of women in the German Democratic Republic has been the subject of a considerable number of studies. The approach has generally been of a sociological or socio-political nature. In this thesis I propose to go one step further by examining the information that may be gained from literary sources. In a state where the media are subject to censorship, and thus controlled, one can refer to literature as an acknowledged source of inside information. Literary works often provide a forum for the formulation and discussion of ideas, which could not be aired elsewhere. Chapter 1 shows why literature, which had always been allocated a special role by the GDR's leading party, the SED, may be regarded as a reliable indicator of everyday life in that country. In this thesis I compare the findings of an analysis of women's literature with sociological data on the one hand and the portrayal of the "ideal" women in GDR media and official writings on the other. The thesis takes an interdisciplinary approach and draws on sources in political, legal, sociological, and cultural fields alike. This constellation of sources allows me to show that the views that female writers expressed in their works frequently coincide with sociological findings. Both of these sources were frequently found to be at odds with statements made in official writings and the media. Such insights could not have been provided by a study conducted from within one discipline.

A legal perspective of integrated surface mining, solid waste landfill reclamation and land conservation

In the area of international environmental law this thesis proposes the formulation of one-step planning and permitting regulation for the integrated utilisation of new surface mines as depositories for municipal solid waste. Additionally, the utilisation of abandoned and currently operated surface mines is proposed as solid waste landfills as an integral step in their reclamation. Existing laws, litigation and issues in the United Kingdom, the U.S. and Canada are discussed because of their common legal system, language and heritage. The critical shortage of approved space for disposal of solid waste has caused an urgent and growing problem for both the waste disposal industry and society. Surface mining can serve three important environmental and societal functions inuring to the health and welfare of the public: (1) providing basic minerals for goods and construction; (20 sequentially, to provide critically needed, safe burial sites for society's wastes, and (3) to conserve land by dual purpose use and to restore derelict land to beneficial surface use. Currently, the first two functions are treated environmentally, and in regulation, as two different siting problems, yet they both are earth-disturbing and excavating industries requiring surface restoration. The processes are largely duplicative and should be combined for better efficiency, less earth disturbance, conservation of land, and for fuller and better reclamation of completed surface mines returning the surfaces to greater utility than present mined land reclamation procedures. While both industries are viewed by a developed society and its communities as "bad neighbours", they remain essential and critical for mankind's existence and welfare. The study offers successful examples of the integrated process in each country. The study argues that most non-fuel surface mine openings, if not already safe, can economically, through present containment technology, be made environmentally safe for use as solid waste landfills. Simultaneously, the procedure safeguards and monitors protection of ground and surface waters from landfill contamination.

Incoherent fibre supercontinuum generation for all-optical random number generation

Random number generation is a central component of modern information technology, with crucial applications in ensuring communications and information security. The development of new physical mechanisms suitable to directly generate random bit sequences is thus a subject of intense current research, with particular interest in alloptical techniques suitable for the generation of data sequences with high bit rate. One such promising technique that has received much recent attention is the chaotic semiconductor laser systems producing high quality random output as a result of the intrinsic nonlinear dynamics of its architecture [1]. Here we propose a novel complementary concept of all-optical technique that might dramatically increase the generation rate of random bits by using simultaneously multiple spectral channels with uncorrelated signals - somewhat similar to use of wave-division-multiplexing in communications. We propose to exploit the intrinsic nonlinear dynamics of extreme spectral broadening and supercontinuum (SC) generation in optical fibre, a process known to be often associated with non-deterministic fluctuations [2]. In this paper, we report proof-of concept results indicating that the fluctuations in highly nonlinear fibre SC generation can potentially be used for random number generation.

Characterisation and surface-profiling techniques for composite particles produced by dry powder coating in pharmaceutical drug delivery

The production of composite particles using dry powder coating is a one-step, environmentally friendly, process for the fabrication of particles with targeted properties and favourable functionalities. Diverse functionalities, such flowability enhancement, content uniformity, and dissolution, can be developed from dry particle coating. In this review, we discuss the particle functionalities that can be tailored and the selection of characterisation techniques relevant to understanding their molecular basis. We address key features in the powder blend sampling process and explore the relevant characterisation techniques, focussing on the functionality delivered by dry coating and on surface profiling that explores the dynamics and surface characteristics of the composite blends. Dry particle coating is a solvent- and heat-free process that can be used to develop functionalised particles. However, assessment of the resultant functionality requires careful selection of sensitive analytical techniques that can distinguish particle surface changes within nano and/or micrometre ranges.

Nonlinearity compensation in multi-rate 28 Gbaud WDM systems employing optical and digital techniques under diverse link configurations

Digital back-propagation (DBP) has recently been proposed for the comprehensive compensation of channel nonlinearities in optical communication systems. While DBP is attractive for its flexibility and performance, it poses significant challenges in terms of computational complexity. Alternatively, phase conjugation or spectral inversion has previously been employed to mitigate nonlinear fibre impairments. Though spectral inversion is relatively straightforward to implement in optical or electrical domain, it requires precise positioning and symmetrised link power profile in order to avail the full benefit. In this paper, we directly compare ideal and low-precision single-channel DBP with single-channel spectral-inversion both with and without symmetry correction via dispersive chirping. We demonstrate that for all the dispersion maps studied, spectral inversion approaches the performance of ideal DBP with 40 steps per span and exceeds the performance of electronic dispersion compensation by ~3.5 dB in Q-factor, enabling up to 96% reduction in complexity in terms of required DBP stages, relative to low precision one step per span based DBP. For maps where quasi-phase matching is a significant issue, spectral inversion significantly outperforms ideal DBP by ~3 dB.