The ecology of paper mill by-product and its evaluation as a casing medium in the culture of Agaricus bisporus (Lange) Pilat

Effluent from pulp and paper production at the Kemsley mill of Bowaters U.K. Paper Company Limited passes through two treatment stages before its discharge into the Swale estuary. Suspended material removed during treatment is deposited on wasteground as a thin sludge. The solids it contains are mainly wood components lost during pulp production, whilst it also has a high salt content, derived from chemicals used in pulping processes. After deposition the sludge undergoes an ageing process during which it dries out and its salt content is reduced. This ageing can be reproduced and accelerated by improved drainage under controlled conditions. The paper mill sludge was investigated as a casing medium in the culture of Agaricus bisporus (Lange) Pilat, the cultivated mushroom. It was unsuitable up to one year from deposition due largely to the inhibitory effect of its salt content on fruiting. Material eighteen months or more in age gave yields comparable to standard peat casing. Before use as a casing the material must be shredded to a satisfactory structure, neutralised with chalk, and pasteurised to eliminate organisms harmful to the crop. The prepared medium has a high water holding capacity and a structure resilient to management procedures, important requirements of a good casing. A passive movement of salts from the compost to the casing was shown to occur during culture, capable of enhancing the natural decline in cropping if sufficiently great. The ions chloride, potassium, sodium and sulphate were shown to be responsible, their damaging effects being due to high conductivity created in the casing. Studies of elements available during culture suggested phosphate availability in the compost could limit crop potential, whilst iron released by mycelium of A.bisporus in the casing may be utilised by associated micro-organisms.

A heat metering system for energy management on an industrial site

Faced with a future of rising energy costs there is a need for industry to manage energy more carefully in order to meet its economic objectives. A problem besetting the growth of energy conservation in the UK is that a large proportion of energy consumption is used in a low intensive manner in organisations where they would be responsibility for energy efficiency is spread over a large number of personnel who each see only small energy costs. In relation to this problem in the non-energy intensive industrial sector, an application of an energy management technique known as monitoring and targeting (M & T) has been installed at the Whetstone site of the General Electric Company Limited in an attempt to prove it as a means for motivating line management and personnel to save energy. The objective energy saving for which the M & T was devised is very specific. During early energy conservation work at the site there had been a change from continuous to intermittent heating but the maintenance of the strategy was receiving a poor level of commitment from line management and performance was some 5% - 10% less than expected. The M & T is concerned therefore with heat for space heating for which a heat metering system was required. Metering of the site high pressure hot water system posed technical difficulties and expenditure was also limited. This led to a ‘tin-house' design being installed for a price less than the commercial equivalent. The timespan of work to achieve an operational heat metering system was 3 years which meant that energy saving results from the scheme were not observed during the study. If successful the replication potential is the larger non energy intensive sites from which some 30 PT savings could be expected in the UK.

The complements towards developing a new risk management framework and Its applicability to the Nigerian power sector

The availability of regular supply has been identified as one of the major stimulants for the growth and development of any nation and is thus important for the economic well-being of a nation. The problems of the Nigerian power sector stems from a lot of factors culminating in her slow developmental growth and inability to meet the power demands of her citizens regardless of the abundance of human and natural resources prevalent in the nation. The research therefore had the main aim of investigating the importance and contributions of risk management to the success of projects specific to the power sector. To achieve this aim it was pertinent to examine the efficacy of risk management process in practice and elucidate the various risks typically associated with projects (Construction, Contractual, Political, Financial, Design, Human resource and Environmental risk factors) in the power sector as well as determine the current situation of risk management practice in Nigeria. To address this factors inhibiting the proficiency of the overarching and prevailing issue which have only been subject to limited in-depth academic research, a rigorous mixed research method was adopted (quantitative and qualitative data analysis). A review of the Nigeria power sector was also carried out as a precursor to the data collection stage. Using purposive sampling technique, respondents were identified and a questionnaire survey was administered. The research hypotheses were tested using inferential statistics (Pearson correlation, Chi-square test, t-test and ANOVA technique) and the findings revealed the need for the development of a new risk management implementation Framework. The proposed Framework was tested within a company project, for interpreting the dynamism and essential benefits of risk management with the aim of improving the project performances (time), reducing the level of fragmentation (quality) and improving profitability (cost) within the Nigerian power sector in order to bridge a gap between theory and practice. It was concluded that Nigeria’s poor risk management practices have prevented it from experiencing strong growth and development. The study however, concludes that the successful implementation of the developed risk management framework may help it to attain this status by enabling it to become more prepared and flexible, to face challenges that previously led to project failures, and thus contributing to its prosperity. The research study provides an original contribution theoretically, methodologically and practically which adds to the project risk management body of knowledge and to the Nigerian power sector.

The growing importance of inter-company collaboration

Guest editorial: This special issue has been drawn from papers that were published as part of the Second European Conference on Management of Technology (EuroMOT) which was held at Aston Business School (Birmingham, UK) 10-12 September 2006. This was the official European conference for the International Association for Management of Technology (IAMOT); the overall theme of the conference was “Technology and global integration.” There were many high-calibre papers submitted to the conference and published in the associated proceedings (Bennett et al., 2006). The streams of interest that emerged from these submissions were the importance of: technology strategy, innovation, process technologies, managing change, national policies and systems, research and development, supply chain technology, service and operational technology, education and training, small company incubation, technology transfer, virtual operations, technology in developing countries, partnership and alliance, and financing and investment. This special issue focuses upon the streams of interest that accentuate the importance of collaboration between different organisations. Such organisations vary greatly in character; for instance, they may be large or small, publicly or privately owned, and operate in manufacturing or service sectors. Despite these varying characteristics they all have something in common; they all stress the importance of inter-organisational collaboration as a critical success factor for their organisation. In today's global economy it is essential that organisations decide what their core competencies are what those of complementing organisations are. Core competences should be developed to become a bases of differentiation, leverage and competitive advantage, whilst those that are less mature should be outsourced to other organisations that can claim to have had more recognition and success in that particular core competence (Porter, 2001). This strategic trend can be observed throughout advanced economies and is growing strongly. If a posteriori reasoning is applied here it follows that organisations could continue to become more specialised in fewer areas whilst simultaneously becoming more dependent upon other organisations for critical parts of their operations. Such actions seem to fly in the face of rational business strategy and so the question must be asked: why are organisations developing this way? The answer could lie in the recent changes in endogenous and exogenous factors of the organisation; the former emphasising resource-based issues in the short-term, and strategic positioning in the long-term whilst the later emphasises transaction costs in the short-term and acquisition of new skills and knowledge in the long-term. For a harmonious balance of these forces to prevail requires organisations to firstly declare a shared meta-strategy, then to put some cross-organisational processes into place which have their routine operations automated as far as possible. A rolling business plan would review, assess and reposition each organisation within this meta-strategy according to how well they have contributed (Binder and Clegg, 2006). The important common issue here is that an increasing number of businesses today are gaining direct benefit from increasing their levels of inter-organisational collaboration. Such collaboration has largely been possible due to recent technological advances which can make organisational structures more agile (e.g. the extended or the virtual enterprise), organisational infra-structure more connected, and the sharing of real-time information an operational reality. This special issue consists of research papers that have explored the above phenomenon in some way. For instance, the role of government intervention, the use of internet-based technologies, the role of research and development organisations, the changing relationships between start-ups and established firms, the importance of cross-company communities of practice, the practice of networking, the front-loading of large-scale projects, innovation and the probabilistic uncertainties that organisations experience are explored in these papers. The cases cited in these papers are limited as they have a Eurocentric focus. However, it is hoped that readers of this special issue will gain a valuable insight into the increasing importance of collaborative practices via these studies.

Knowledge management in a New Zealand tree farming company:Ambiguity and resistance to the "technology solution"

Purpose - Managers at the company attempt to implement a knowledge management information system in an attempt to avoid loss of expertise while improving control and efficiency. The paper seeks to explore the implications of the technological solution to employees within the company. Design/methodology/approach - The paper reports qualitative research conducted in a single organization. Evidence is presented in the form of interview extracts. Findings - The case section of the paper presents the accounts of organizational participants. The accounts reveal the workers' reactions to the technology-based system and something of their strategies of resistance to the system. These accounts also provide glimpses of the identity construction engaged in by these knowledge workers. The setting for the research is in a knowledge-intensive primary industry. Research was conducted through observation and interviews. Research limitations/implications - The issues identified are explored in a single case-study setting. Future research could look at the relevance of the findings to other settings. Practical implications - The case evidence presented indicates some of the complexity of implementation of information systems in organizations. This could certainly be seen as more evidence of the uncertainty associated with organizational change and of the need for managers not to expect an easy adoption of intrusive IT solutions. Originality/value - This paper adds empirical insight to a largely conceptual literature. © Emerald Group Publishing Limited.

Interhemispheric differences of spectral power in expressive language:a MEG study with clinical applications

In the last decade we have seen an exponential growth of functional imaging studies investigating multiple aspects of language processing. These studies have sparked an interest in applying some of the paradigms to various clinically relevant questions, such as the identification of the cortical regions mediating language function in surgical candidates for refractory epilepsy. Here we present data from a group of adult control participants in order to investigate the potential of using frequency specific spectral power changes in MEG activation patterns to establish lateralisation of language function using expressive language tasks. In addition, we report on a paediatric patient whose language function was assessed before and after a left hemisphere amygdalo-hippocampectomy. Our verb generation task produced left hemisphere decreases in beta-band power accompanied by right hemisphere increases in low beta-band power in the majority of the control group, a previously unreported phenomenon. This pattern of spectral power was also found in the patient's post-surgery data, though not her pre-surgery data. Comparison of pre and post-operative results also provided some evidence of reorganisation in language related cortex both inter- and intra-hemispherically following surgery. The differences were not limited to changes in localisation of language specific cortex but also changes in the spectral and temporal profile of frontal brain regions during verb generation. While further investigation is required to establish concordance with invasive measures, our data suggest that the methods described may serve as a reliable lateralisation marker for clinical assessment. Furthermore, our findings highlight the potential utility of MEG for the investigation of cortical language functioning in both healthy development and pathology.

Biomass fuelled combined heat and power:situation in the UK and the Netherlands

Combined Heat and Power (CHP) is the simultaneous generation of usable heat and power in a single process. Despite its obvious advantages in terms of increased efficiency when compared to a single heat or power generation unit, there are a number of technical and economic reasons that have limited their selection. Biomass resources can be, and actually are used as fuel in CHP installations; however several hurdles have to be sorted beforehand, among the most important is the fact that biomass energy sources are not as energy intense as conventional CHP fuels. The ultimate outcome is a limited number of CHP units making use of biomass as fuel. Even fewer CHP units use bioliquids (e.g.: fast pyrolysis biomass liquids, biodiesel and vegetable oil). The Bioliquid-CHP project is carried out by a consortium of seven European and Russian complementary partners, funded by the EU and by the Federal Agency for Science and Innovation of the Russian Federation. The project aim is to develop microturbine and internal combustion engine adaptations in order to adjust these prime movers to bioliquids for CHP applications. This paper will show a summary of the current biomass CHP installations in the UK and the Netherlands, making reference to number of units, capacity, fuel used, the conversion technology involved and the preferred prime movers. The information will give an insight of the current market, with probable future trends and areas where growth could be expected. A similar paper describing the biomass CHP situation in Italy and Russia will be prepared in the near future.

Biomass-based small and micro combined heat and power (CHP) systems:application and status in the United Kingdom

This chapter discusses the current state of biomass-based combined heat and power (CHP) production in the UK. It presents an overview of the UK's energy policy and targets which are relevant to the deployment of biomass-based CHP and summarises the current state for renewable, biomass and CHP. A number of small-scale biomass-based CHP projects are described while providing some indicative capital costs for combustion, pyrolysis and gasification technologies. For comparison purposes, it presents an overview of the respective situation in Europe and particularly in Sweden, Finland and Denmark. There is also a brief comment about novel CHP technologies in Austria. Finally it draws some conclusions on the potential of small-scale biomass CHP in the UK. © 2011 Woodhead Publishing Limited All rights reserved.

Addressing the project implementation challenges in the Saudi Arabian power supply industry: an investigative approach towards improving project delivery

For many decades, the Kingdom of Saudi Arabia has been widely known for being a reliable oil exporter. This fact, however, has not exempted it from facing significant domestic energy challenges. One of the most pressing of these challenges involves bridging the widening electricity supply-demand gap where, currently, the demand is growing at a very fast rate. One crucial means to address this challenge is through delivering power supply projects with maximum efficiency. Project delivery delay, however, is not uncommon in this highly capital-intensive industry, indicating electricity supplies are not coping with the demand increases. To provide a deeper insight into the challenges of project implementation and efficient practice, this research adopts a pragmatic approach by triangulating literature, questionnaires and semi-structured interviews. The research was conducted in the Saudi Arabian power supply industry – Western Operating Area. A total of 105 usable questionnaires were collected, and 28 recorded, semi-structured interviews were conducted, analysed and synthesised to produce a conceptual model of what constitutes the project implementation challenges in the investigated industry. This was achieved by conducting a comprehensive ranking analysis applied to all 58 identified and surveyed factors which, according to project practitioners in the investigated industry, contribute to project delay. 28 of these project delay factors were selected as the "most important" ones. Factor Analysis was employed to structure these 28 most important project delay factors into the following meaningful set of 7 project implementation challenges: Saudi Electricity Company's contractual commitments, Saudi Electricity Company's communication and coordination effectiveness, contractors' project planning and project control effectiveness, consultant-related aspects, manpower challenges and material uncertainties, Saudi Electricity Company's tendering system, and lack of project requirements clarity. The study has implications for industry policy in that it provides a coherent assessment of the key project stakeholders' central problems. From this analysis, pragmatic recommendations are proposed that, if enacted, will minimise the significance of the identified problems on future project outcomes, thus helping to ensure the electricity supply-demand gap is diminished.

A micro gas turbines for UK domestic combined heat and power

Various micro-radial compressor configurations were investigated using one-dimensional meanline and computational fluid dynamics (CFD) techniques for use in a micro gas turbine (MGT) domestic combined heat and power (DCHP) application. Blade backsweep, shaft speed, and blade height were varied at a constant pressure ratio. Shaft speeds were limited to 220 000 r/min, to enable the use of a turbocharger bearing platform. Off-design compressor performance was established and used to determine the MGT performance envelope; this in turn was used to assess potential cost and environmental savings in a heat-led DCHP operating scenario within the target market of a detached family home. A low target-stage pressure ratio provided an opportunity to reduce diffusion within the impeller. Critically for DCHP, this produced very regular flow, which improved impeller performance for a wider operating envelope. The best performing impeller was a low-speed, 170 000 r/min, low-backsweep, 15° configuration producing 71.76 per cent stage efficiency at a pressure ratio of 2.20. This produced an MGT design point system efficiency of 14.85 per cent at 993 W, matching prime movers in the latest commercial DCHP units. Cost and CO2 savings were 10.7 per cent and 6.3 per cent, respectively, for annual power demands of 17.4 MWht and 6.1 MWhe compared to a standard condensing boiler (with grid) installation. The maximum cost saving (on design point) was 14.2 per cent for annual power demands of 22.62 MWht and 6.1 MWhe corresponding to an 8.1 per cent CO2 saving. When sizing, maximum savings were found with larger heat demands. When sized, maximum savings could be made by encouraging more electricity export either by reducing household electricity consumption or by increasing machine efficiency.

The dynamics of organizational change : an analysis of power, professions and new managerialism in the case of CoastElectric

It is widely accepted that the Thatcher years and their immediate aftermath were associated with substantive social and organizational change. The privatisation programme, 'the rolling back of the State', prosecuted by the successive Conservative Governments from 1979-1997 was a central pillar of Governmental policy. This thesis seeks to engage with privatization through the of CoastElectric, a newly privatised Regional Electricity Company. This thesis contributes to the extant understanding of the dynamics of organizational change in four major ways. Firstly, the study into CoastElectric addresses the senior management decision making within the organization: in particular, it will attempt to make sense of 'why' particular decisions were made. The theoretical backdrop to this concern will draw on the concepts of normalization, cultural capital and corporate fashion. The argument presented in this thesis is that the decision-making broadly corresponded with that which could be considered to be at the vanguard of mangerialist thought. However, a detailed analysis suggested that at different junctures in CoastElectric's history there were differences in the approach to decision making that warranted further analysis. The most notable finding was that the relative levels of new managerialist cultural capital possessed by the decision-making elite had an important bearing upon whether the decision was formulated either endogenously or exogenously, with the assistance of cultural intermediaries such as management consultants. The thesis demonstrates the importance of the broader discourse of new managerialism in terms of shaping what is considered to be a 'commonsensical, rational' strategy. The second concern of this thesis is that of the process of organizational change. The study of CoastElectric attempts to provide a rich account of the dynamics of organizational change. This is realized through, first, examining the pre-existing context of the organization; second, through analyzing the power politics of change interventions. The master concepts utilised in this endeavour are that of: dividing practices, the establishment of violent hierarchies between competing discourses; symbolic violence; critical turning points; recursiveness; creative destruction; legitimation strategies and the reconstitution of subjects in the workplace.

Management role in employee participation:a comparative study of multi-national enterprises in India and the U.K.

This research is an Anglo-Indian comparative case study. It studies managerial action in the participation arena of two British multi-nationals i.e. Cadbury Limited and ICI plc. The research was carried out in matched pairs of factories of the above named companies, located in the Midlands of the UK and in Bombay in India. The data for this research was collected through semi-structured interviews with managers and non-management actors, study of company documents and non-participant observation of some participation forums. The research conceptualises the idea of a `participation arena' consisting of the structures, processes, purposes and dynamics of participation. This arena is visualised as broadly reflecting the organisation structure and can be divided into corporate, unit and shopfloor level. Managerial action in this arena is examined in terms of interaction between three sets of factors i.e. company business objectives, strategies and policies; managerial values of power and control; and the responses of unions. Similarities and differences between management action in the home and host plants of the two multi-national companies are also examined. The major findings of the research are as follows. There is significant difference between the participation arena of the parent and the subsidiary company. The latter is marked by absence of higher level participation forums and lack of opportunity for employees to discuss, let alone influence, key decisions. This results from parent company control over key activities of the subsidiary. The similarities in management action in the participation arenas of the two companies in both countries can be attributed to the operation of the three sets of factors mentioned above. Nevertheless, the particular circumstances of each company are a greater influence on managerial action than the national context. Finally, future areas of research in this field are explored.

The political shaping of energy technology:combined heat and power in Britain

There has been negligible adoption of combined heat and power (CHP) for district heating (DH) in Britain, despite continued advocacy. This thesis constructs an account of the treatment of the option, and devises a framework for explanation. Analysis of technological development and adoption, it is argued, should be similar to that of other social processes, and be subject to the same requirements and criticisms. They will, however, show features peculiar to the institutions developing and selecting technologies, their relation to different social groups, and the forms of knowledge in and about technology. Conventional approaches - organisation and interorganisation theories, and analyses of policy-making - give useful insights but have common limitations. Elements of an analytical framework situating detailed issues and outcomes in a structured historical context are derived from convergent radical critiques. Thus activity on CHP/DH is essentially shaped by the development and relations of energy sector institutions: central and local government, nationalised industries and particularly the electricity industry. Analysis of them is related to the specific character of the British state. A few CHP and DH installations were tried before 1940. During postwar reconstruction, extensive plans for several cities were abandoned or curtailed. In the 1960s and 70s, many small non-CHP DH schemes were installed on housing estates. From the mid-70s, the national potential of CHP/DH has been reappraised, with widespread support and favourable evaluations, but little practical progress. Significant CHP/DH adoption is shown to have been systematically excluded ultimately by the structure of energy provision; centralised production interests dominate and co-ordination is weak. Marginal economics and political commitment have allowed limited development in exceptional circumstances. Periods of upheaval provided greater opportunity and incentive for CHP/DH but restructuring eventually obstructed it. Explanation of these outcomes is shown to require analysis at several levels, from broad context to detailed action.

Integrated manufacturing systems design in a multi-product company

Using a hydraulic equipment manufacturing plant as the case study, this work explores the problems of systems integration in manufacturing systems design, stressing the behavioural aspects of motivation and participation, and the constraints involved in the proper consideration of the human sub-system. The need for a simple manageable modular organisation structure is illustrated, where it is shown, by reference to systems theory, how a business can be split into semi-autonomous operating units. The theme is the development of a manufacturing system based on an analysis of the business, its market, product, technology and constraints, coupled with a critical survey of modern management literature to develop an integrated systems design to suit a specific company in the current social environment. Society currently moves through a socio-technical revolution with man seeking higher levels of motivation. The transitory environment from an autocratic/paternalistic to a participative operating mode demands systems parameters only found to a limited extent in manufacturing systems today. It is claimed, that modern manufacturing systems design needs to be based on group working, job enrichment, delegation of decision making and reduced job monotony. The analysis shows how negative aspects of cellular manufacture such as lack of flexibility and poor fixed asset utilisation are relatively irrelevant and misleading in the broader context of the need to come to terms with the social stresses imposed on a company operating in the industrial environment of the present and the immediate future.