The casing layer in the culture of Agaricus bisporus, the cultivated mushroom

The casing layer is an essential component of the system employed in the culture of Agaricus bisporus. The literature appropriate to the casing layer is fully reviewed, including aspects relating to fructification and morphogenesis in A.bisporus, together with an appraisal of the various media employed, their properties and functions, and the commercial significance of the casing layer. Equipment is described for use in experiments in mushroom culture, based on a scaled-down version of normal growing technique, allowing the analysis of both weights and number of fruitbodies forming, which was useful in assessing the effects of different casing treatments. The basic steps in the production of fruitbodies in A.bisporus.are described, including a photographic study of the colonisation of casing and fructification. Various alterations to the physical structure of peat/chalk casing mixtures were found to have an effect on fructification; those causing an opening-out of the casing structure tended to give better yields, especially in the early stages of production. It was shown that, in order to obtain greater yield through casing amendment, fructification must be stimulated, giving increased numbers of fruitbodies, disproportionate to their total weight and consequently of lower mean weight. A synthetic casing medium based on the light glass-like mineral, perlite, was developed. The best formula obtained was -.1 part perlite: 1 part montmorillonite clay (by weight): 3 parts 0.01% glucose solution. Perlite/montmorillonite casing could be improved by adding compost colonised by mycelium of A.bisporus, or adding a peat-chalk casing extract. Perlite was also found to be suitable for admixture with the standard casing medium and a mixture of equal parts by volume performed as well as the peat/chalk casing normally used.

Studies on the composition and nutritional value of the cultivated mushroom, agaricus bisporus (Lange) Sing

The effects of various cultural conditions on the composition and nutritional quality of Agaricus bisporus (Lange) Sing. were investigated. Variation in composition was found between different classes of sample. Sampling techniques were standardised to allow for major variations in the different developmental stages and culture ages. Fruitbodies were found to be of low calorific value but contained protein of high digestibility and quality, containing all the essential amino acids required by man. Quantitative estimates of the sulphur-containing amino acids indicated that fruitbodies were deficient in methionine and cysteine. The extent of water application and the supplementation of conventional substrates with various nitrogen-containing substances, influenced yield and composition, establishing the importance of these two factors in the physiology of fruitbodies and cultural management. Storage conditions influenced composition, high temperatures being deleterious to the nutritional value of fruitbodies. Submerged culture techniques were used to investigate the effects of various nutrients on growth and composition of mushroom mycelium, with special reference to the sulphur-containing amino acids. Yield and composition were greatly affected by the carbon:nitrogen ratio of the medium and by the nitrogen source. Significant increases in mycelial methionine content were observed on the addition of inorganic sulphate, the methionine derivative N-acetyl-L-methionine, and L-methionine. A greater increase in methionine content was obtained when the biomass of a thermophilic bacterium isolated from compost was used as a nitrogen source.

The ecology of paper mill by-product and its evaluation as a casing medium in the culture of Agaricus bisporus (Lange) Pilat

Effluent from pulp and paper production at the Kemsley mill of Bowaters U.K. Paper Company Limited passes through two treatment stages before its discharge into the Swale estuary. Suspended material removed during treatment is deposited on wasteground as a thin sludge. The solids it contains are mainly wood components lost during pulp production, whilst it also has a high salt content, derived from chemicals used in pulping processes. After deposition the sludge undergoes an ageing process during which it dries out and its salt content is reduced. This ageing can be reproduced and accelerated by improved drainage under controlled conditions. The paper mill sludge was investigated as a casing medium in the culture of Agaricus bisporus (Lange) Pilat, the cultivated mushroom. It was unsuitable up to one year from deposition due largely to the inhibitory effect of its salt content on fruiting. Material eighteen months or more in age gave yields comparable to standard peat casing. Before use as a casing the material must be shredded to a satisfactory structure, neutralised with chalk, and pasteurised to eliminate organisms harmful to the crop. The prepared medium has a high water holding capacity and a structure resilient to management procedures, important requirements of a good casing. A passive movement of salts from the compost to the casing was shown to occur during culture, capable of enhancing the natural decline in cropping if sufficiently great. The ions chloride, potassium, sodium and sulphate were shown to be responsible, their damaging effects being due to high conductivity created in the casing. Studies of elements available during culture suggested phosphate availability in the compost could limit crop potential, whilst iron released by mycelium of A.bisporus in the casing may be utilised by associated micro-organisms.

The microbial ecology of cow slurry in vermiculture beds

The suitability of cow slurry as a substrate for vermicomposting by Eisenia fetida was investigated. Particular attention was given to the effects of the earthworm on the decomposition and stabilisation of the slurry; and to the interactions between E. fetida and the microflora of the substrate. Assessment of the chemical and microbiological changes in cow slurry stored under forced aeration, and subsequently in shallow trays, showed that neither method was suitable for the treatment of slurry. A comparison of two methods of vermicomposting showed that top-feeding of slurry was more efficient in promoting earthworm growth and cocoon production than the mixing of slurry with solid materials. Management practices were found to have an important influence on the efficiency of the process. An investigation o:f the effect of E. fetida. on the decomposition of slurry indicated that the presence of this earthworm enhanced the stabilisation of the substrate and increased the plant-available nitrogen content. Specific nutritional interactions were observed between E. fetida and micro-organisms in sand/cellulose microcosms. The earthworms were found to be feeding directly upon the cells of certain micro-organisms. Other species were found to be toxic to E. fetida.. A technique was developed :for the production of axenic E. fetida., and the use of such earthworms in :feeding experiments confirmed the importance of some micro-organisms in earthworm nutrition. The seeding of vermiculture beds with one such micro-organism stimulated earthworm growth and consumption of the substrate. Vermicomposted mixtures of cow slurry and spent mushroom compost were shown to have potential application as casing materials in mushroom cultivation. The findings of this study indicate the suitability of vermicomposting as a method for the stabilisation of intensively-produced cow slurry, and give some indication of the importance of micro-organisms in the nutrition of E. fetida.

A study in the reduction of efficiency of nitrogen oxide removal catalysts for automobiles

Automotive catalysts are the most effective short-term answer to air pollution from automobiles. Since strict control of exhaust emissions is, or will be,covered by legislation in most developed countries in the world, catalytic devices will be increasingly fitted to cars. There is consequently an urgent need for the development of catalysts that will not compete for scarce precious metal resources. A number of problems have already been identified in connection with base metal catalysts but quantitative investigations are lacking. The base metal reduction catalysts developed by Imperial Chemical Industries Limited, catalysts and Chemical Group, in collaboration with the Air Pollution Control Laboratory, B L Cars Limited for automotive emission control, are susceptible to de-activation by three major mechanisms. These are: physical loss of the wash-coat (a high surface area coating which supports the active species), aggregation of the active species and poisoning by fuel and engine oil additives. This thesis is especially concerned with the first two of these and attempts to indicate the relative magnitude .of their effect on the activity of. the catalysts. Aggregation of the active species or sintering, as it is loosely called, was studied by using impregnated granules to overcome effects due to the loss of the wash-coat. Samples were aged in a synthetic exhaust gas, free from poisons, and metal crystallite sizes were measured by scanning-electron microscopy. The increase in particle size was correlated with the loss in catalytic activity. In order to maintain a link with the real conditions of service a number of monolithic catalysts were tested in an engine-dynamometer and several previously tested endurance catalysts were examined. A mechanism is proposed for the break-up and subsequent 10s.5 of the wash-coat and suggestions for improved resistance to loss of the' coating and active species are proposed.

The formation and impact of hazard control policy:a study of the regulation of white lead paint in Britain

Government regulation of industrial hazards is examined in the context of the economic and technical processes of industrial development. Technical problems and costs of control are considered as factors in both the formation and impact of regulation. This thesis focuses on an historical case-study of the regulation of the hazard to painting workers from the use of lead pigments in paint. A regulatory strategy based on the prohibition of lead paints gained initial acceptance within the British state in 1911, but was subsequently rejected in favour of a strategy that allowed continued use of lead paint subject to hygiene precautions. The development of paint technology and its determinants, including concern about health hazards, are analysed, focusing on the innovation and diffusion into the paint industry of the major white pigments: white lead (PbC03 .PB(OH)2)and its substitutes. The process of regulatory development is examined, and the protracted and polarised regulatory d~bate contrasted to the prevailing 'consensual' methods of workplace regulation. The rejection of prohibition is analysed in terms of the different political and technical resources of those groups in conflict over this policy. This highlights the problems of consensus formation around such a strategy, and demonstrates certain constraints on state regulatory activity, particularly regarding industrial development. Member-states of the International Labour Organisation agreed to introduce partial prohibition of lead paint in 1921. Whether this was implemented is related to the economic importance of lead and non-lead metal and pigment industries to a nation. An analysis is made of the control of lead poisoning. The rate of control is related to the economic and technological trajectory of the regulated industry. Technical and organisational characteristics are considered as well as regulatory factors which range from voluntary compliance and informal pressures to direct legal requirements. The implications of this case-study for the analysis of the development and impacts of regulation are assessed.

High temperature gas cleaning for advanced syngas utilization:Paper # 95

Biofuels and chemicals from biomass mean the gasification of biogenic feedstocks and the synthesis via methanol, dimethylester (DME) or Fischer-Tropsch products. To prevent the sensitive synthesis catalysts from poisoning the syngas must be free of tar and particulates. The trace concentrations of S-, C1-, N-species, alkali and heavy metals must be of the order of a few ppb. Moreover maximum conversion efficiency will be achieved performing the gas cleaning above the synthesis conditions. The concept of an innovative dry HTHP syngas cleaning is presented. Based on the HT particle filtration and suitable sorption and catalysis processes for the relevant contaminants a total concept will be derived, which leads to a syngas quality required for synthesis catalysts in only 2 combined stages. The experimental setup for the HT gas cleaning behind the 60 kWtherm entrained flow gasifier REGA of the institute is described. Results from HT filter experiments in pilot scale are presented. The performance of 2 natural minerals for HC1 and H2S sorption is discussed with respect to the parameters temperature, surface and residence time. Results from lab scale investigations on low temperature tar catalysts' performance (commercial and proprietary development) are discussed finally.

New insights in the deactivation of sulfonic modified SBA-15 catalysts for biodiesel production from low-grade oleaginous feedstock

Arenesulfonic-acid functionalized SBA-15 materials have been used in the production of biodiesel from low grade oleaginous feedstock. These materials display an outstanding catalytic activity, being able to promote the transformation of crude palm oil with methanol into fatty acid methyl esters with high yield (85%) under mild reaction conditions. However, high sensitivity of the catalyst against poisoning by different substances has also been detected. Thus, alkaline metal cations, such as sodium or potassium exert a negative influence on the catalytic activity of these materials, being necessary amounts around 500 ppm of sodium in the reaction media to decrease the catalytic activity of these materials to a half of its initial value in just two reaction runs. The deactivation of arenesulfonic acid functionalized SBA-15 materials seems to occur in this case by ion exchange of the acid protons at the sulfonic groups. Organic unsaponifiable compounds like lecithin or retinol also induce a negative influence in the catalytic activity of these sulfonic acid-based materials, though not so intense as in the case of alkaline metals. The deactivating mechanism associated to the influence of the organic compounds seems to be linked to the adsorption of such substances onto the catalytic acid sites as well as on the silica surface. The accumulation of lecithin in the surface of catalyst, observed by means of thermogravimetric analysis, suggest the creation of a strong interaction, probably by ion pair, between this compound and the sulfonic acid group.