Early design verification of complex assembly variability using a hybrid - model based and physical testing - methodology

Design verification in the digital domain, using model-based principles, is a key research objective to address the industrial requirement for reduced physical testing and prototyping. For complex assemblies, the verification of design and the associated production methods is currently fragmented, prolonged and sub-optimal, as it uses digital and physical verification stages that are deployed in a sequential manner using multiple systems. This paper describes a novel, hybrid design verification methodology that integrates model-based variability analysis with measurement data of assemblies, in order to reduce simulation uncertainty and allow early design verification from the perspective of satisfying key assembly criteria.

A co-cultured skin model based on cell support membranes

Tissue engineering of skin based on collagen:PCL biocomposites using a designed co-culture system is reported. The collagen:PCL biocomposites having collagen:PCL (w/w) ratios of 1:4, 1:8, and 1:20 have been proven to be biocompatible materials to support both adult normal human epidermal Keratinocyte (NHEK) and mouse 3T3 fibroblast growth in cell culture, respectively, by Dai, Coombes, et al. in 2004. Films of collagen:PCL biocomposites were prepared using non-crosslinking method by impregnation of lyophilized collagen mats with PCL/dichloromethane solutions followed by solvent evaporation. To mimic the dermal/epidermal structure of skin, the 1:20 collagen:PCL biocomposites were selected for a feasibility study of a designed co-culture technique that would subsequently be used for preparing fibroblast/biocomposite/keratinocyte skin models. A 55.3% increase in cell number was measured in the designed co-culture system when fibroblasts were seeded on both sides of a biocomposite film compared with cell culture on one surface of the biocomposite in the feasibility study. The co-culture of human keratinocytes and 3T3 fibroblasts on each side of the membrane was therefore studied using the same co-culture system by growing keratinocytes on the top surface of membrane for 3 days and 3T3 fibroblasts underneath the membrane for 6 days. Scanning electron microscopy (SEM) and immunohistochemistry assay revealed good cell attachment and proliferation of both human keratinocytes and 3T3 fibroblasts with these two types of cells isolated well on each side of the membrane. Using a modified co-culture technique, a co-cultured skin model presenting a confluent epidermal sheet on one side of the biocomposite film and fibroblasts populated on the other side of the film was developed successfully in co-culture system for 28 days under investigations by SEM and immunohistochemistry assay. Thus, the design of a co-culture system based on 1:20 (w/w) collagen:PCL biocomposite membranes for preparation of a bi-layered skin model with differentiated epidermal sheet was proven in principle. The approach to skin modeling reported here may find application in tissue engineering and screening of new pharmaceuticals. © 2005 Elsevier Inc. All rights reserved.

Case based design of knitwear

In the developed world we are surrounded by man-made objects, but most people give little thought to the complex processes needed for their design. The design of hand knitting is complex because much of the domain knowledge is tacit. The objective of this thesis is to devise a methodology to help designers to work within design constraints, whilst facilitating creativity. A hybrid solution including computer aided design (CAD) and case based reasoning (CBR) is proposed. The CAD system creates designs using domain-specific rules and these designs are employed for initial seeding of the case base and the management of constraints. CBR reuses the designer's previous experience. The key aspects in the CBR system are measuring the similarity of cases and adapting past solutions to the current problem. Similarity is measured by asking the user to rank the importance of features; the ranks are then used to calculate weights for an algorithm which compares the specifications of designs. A novel adaptation operator called rule difference replay (RDR) is created. When the specifications to a new design is presented, the CAD program uses it to construct a design constituting an approximate solution. The most similar design from the case-base is then retrieved and RDR replays the changes previously made to the retrieved design on the new solution. A measure of solution similarity that can validate subjective success scores is created. Specification similarity can be used as a guide whether to invoke CBR, in a hybrid CAD-CBR system. If the newly resulted design is suffciently similar to a previous design, then CBR is invoked; otherwise CAD is used. The application of RDR to knitwear design has demonstrated the flexibility to overcome deficiencies in rules that try to automate creativity, and has the potential to be applied to other domains such as interior design.

Nootropia : a user profiling model based on a self-organising term network

Artificial Immune Systems are well suited to the problem of using a profile representation of an individual’s or a group’s interests to evaluate documents. Nootropia is a user profiling model that exhibits similarities to models of the immune system that have been developed in the context of autopoietic theory. It uses a self-organising term network that can represent a user’s multiple interests and can adapt to both short-term variations and substantial changes in them. This allows Nootropia to drift, constantly following changes in the user’s multiple interests, and, thus, to become structurally coupled to the user.

Towards the knowledge-based design of universal influenza epitope ensemble vaccines

Motivation: Influenza A viral heterogeneity remains a significant threat due to unpredictable antigenic drift in seasonal influenza and antigenic shifts caused by the emergence of novel subtypes. Annual review of multivalent influenza vaccines targets strains of influenza A and B likely to be predominant in future influenza seasons. This does not induce broad, cross protective immunity against emergent subtypes. Better strategies are needed to prevent future pandemics. Cross-protection can be achieved by activating CD8+ and CD4+ T cells against highly-conserved regions of the influenza genome. We combine available experimental data with informatics-based immunological predictions to help design vaccines potentially able to induce cross-protective T-cells against multiple influenza subtypes. Results: To exemplify our approach we designed two epitope ensemble vaccines comprising highly-conserved and experimentally-verified immunogenic influenza A epitopes as putative non-seasonal influenza vaccines; one specifically targets the US population and the other is a universal vaccine. The USA-specific vaccine comprised 6 CD8+ T cell epitopes (GILGFVFTL, FMYSDFHFI, GMDPRMCSL, SVKEKDMTK, FYIQMCTEL, DTVNRTHQY) and 3 CD4+ epitopes (KGILGFVFTLTVPSE, EYIMKGVYINTALLN, ILGFVFTLTVPSERG). The universal vaccine comprised 8 CD8+ epitopes: (FMYSDFHFI, GILGFVFTL, ILRGSVAHK, FYIQMCTEL, ILKGKFQTA, YYLEKANKI, VSDGGPNLY, YSHGTGTGY) and the same 3 CD4+ epitopes. Our USA-specific vaccine has a population protection coverage (portion of the population potentially responsive to one or more component epitopes of the vaccine, PPC) of over 96% and 95% coverage of observed influenza subtypes. The universal vaccine has a PPC value of over 97% and 88% coverage of observed subtypes.

Development and validation of a computationally efficient pseudo 3D model for planar SOFC integrated with a heating furnace

Efficient numerical models facilitate the study and design of solid oxide fuel cells (SOFCs), stacks, and systems. Whilst the accuracy and reliability of the computed results are usually sought by researchers, the corresponding modelling complexities could result in practical difficulties regarding the implementation flexibility and computational costs. The main objective of this article is to adapt a simple but viable numerical tool for evaluation of our experimental rig. Accordingly, a model for a multi-layer SOFC surrounded by a constant temperature furnace is presented, trained and validated against experimental data. The model consists of a four-layer structure including stand, two interconnects, and PEN (Positive electrode-Electrolyte-Negative electrode); each being approximated by a lumped parameter model. The heating process through the surrounding chamber is also considered. We used a set of V-I characteristics data for parameter adjustment followed by model verification against two independent sets of data. The model results show a good agreement with practical data, offering a significant improvement compared to reduced models in which the impact of external heat loss is neglected. Furthermore, thermal analysis for adiabatic and non-adiabatic process is carried out to capture the thermal behaviour of a single cell followed by a polarisation loss assessment. Finally, model-based design of experiment is demonstrated for a case study.

A fuzzy AHP based integer linear programming model for the multi-criteria transshipment problem

Purpose – The purpose of this research is to develop a holistic approach to maximize the customer service level while minimizing the logistics cost by using an integrated multiple criteria decision making (MCDM) method for the contemporary transshipment problem. Unlike the prevalent optimization techniques, this paper proposes an integrated approach which considers both quantitative and qualitative factors in order to maximize the benefits of service deliverers and customers under uncertain environments. Design/methodology/approach – This paper proposes a fuzzy-based integer linear programming model, based on the existing literature and validated with an example case. The model integrates the developed fuzzy modification of the analytic hierarchy process (FAHP), and solves the multi-criteria transshipment problem. Findings – This paper provides several novel insights about how to transform a company from a cost-based model to a service-dominated model by using an integrated MCDM method. It suggests that the contemporary customer-driven supply chain remains and increases its competitiveness from two aspects: optimizing the cost and providing the best service simultaneously. Research limitations/implications – This research used one illustrative industry case to exemplify the developed method. Considering the generalization of the research findings and the complexity of the transshipment service network, more cases across multiple industries are necessary to further enhance the validity of the research output. Practical implications – The paper includes implications for the evaluation and selection of transshipment service suppliers, the construction of optimal transshipment network as well as managing the network. Originality/value – The major advantages of this generic approach are that both quantitative and qualitative factors under fuzzy environment are considered simultaneously and also the viewpoints of service deliverers and customers are focused. Therefore, it is believed that it is useful and applicable for the transshipment service network design.

DFIG machine design for maximizing power output based on surrogate optimization algorithm

This paper presents a surrogate-model-based optimization of a doubly-fed induction generator (DFIG) machine winding design for maximizing power yield. Based on site-specific wind profile data and the machine's previous operational performance, the DFIG's stator and rotor windings are optimized to match the maximum efficiency with operating conditions for rewinding purposes. The particle swarm optimization-based surrogate optimization techniques are used in conjunction with the finite element method to optimize the machine design utilizing the limited available information for the site-specific wind profile and generator operating conditions. A response surface method in the surrogate model is developed to formulate the design objectives and constraints. Besides, the machine tests and efficiency calculations follow IEEE standard 112-B. Numerical and experimental results validate the effectiveness of the proposed technologies.

A model to assess the cost effectiveness of statins in achieving the UK National Service Framework target cholesterol levels

Background: Coronary heart disease (CHD) is a public health priority in the UK. The National Service Framework (NSF) has set standards for the prevention, diagnosis and treatment of CHD, which include the use of cholesterol-lowering agents aimed at achieving targets of blood total cholesterol (TC) < 5.0 mmol/L and low density lipoprotein-cholesterol (LDL-C) < 3.0 mmol/L. In order to achieve these targets cost effectively, prescribers need to make an informed choice from the range of statins available. Aim: To estimate the average and relative cost effectiveness of atorvastatin, fluvastatin, pravastatin and simvastatin in achieving the NSF LDL-C and TC targets. Design: Model-based economic evaluation. Methods: An economic model was constructed to estimate the number of patients achieving the NSF targets for LDL-C and TC at each dose of statin, and to calculate the average drug cost and incremental drug cost per patient achieving the target levels. The population baseline LDL-C and TC, and drug efficacy and drug costs were taken from previously published data. Estimates of the distribution of patients receiving each dose of statin were derived from the UK national DIN-LINK database. Results: The estimated annual drug cost per 1000 patients treated with atorvastatin was £289 000, with simvastatin £315 000, with pravastatin £333 000 and with fluvastatin £167 000. The percentages of patients achieving target are 74.4%, 46.4%, 28.4% and 13.2% for atorvastatin, simvastatin, pravastatin and fluvastatin, respectively. Incremental drug cost per extra patient treated to LDL-C and TC targets compared with fluvastafin were £198 and £226 for atorvastatin, £443 and £567 for simvastatin and £1089 and £2298 for pravastatin, using 2002 drug costs. Conclusions: As a result of its superior efficacy, atorvastatin generates a favourable cost-effectiveness profile as measured by drug cost per patient treated to LDL-C and TC targets. For a given drug budget, more patients would achieve NSF LDL-C and TC targets with atorvastatin than with any of the other statins examined.

Computational model of bladder tissue based on its measured optical properties

Urinary bladder diseases are a common problem throughout the world and often difficult to accurately diagnose. Furthermore, they pose a heavy financial burden on health services. Urinary bladder tissue from male pigs was spectrophotometrically measured and the resulting data used to calculate the absorption, transmission, and reflectance parameters, along with the derived coefficients of scattering and absorption. These were employed to create a "generic" computational bladder model based on optical properties, simulating the propagation of photons through the tissue at different wavelengths. Using the Monte-Carlo method and fluorescence spectra of UV and blue excited wavelength, diagnostically important biomarkers were modeled. Additionally, the multifunctional noninvasive diagnostics system "LAKK-M" was used to gather fluorescence data to further provide essential comparisons. The ultimate goal of the study was to successfully simulate the effects of varying excited radiation wavelengths on bladder tissue to determine the effectiveness of photonics diagnostic devices. With increased accuracy, this model could be used to reliably aid in differentiating healthy and pathological tissues within the bladder and potentially other hollow organs.

Inter-organisational knowledge transfer process model

Knowledge management (KM) is an emerging discipline (Ives, Torrey & Gordon, 1997) and characterised by four processes: generation, codification, transfer, and application (Alavi & Leidner, 2001). Completing the loop, knowledge transfer is regarded as a precursor to knowledge creation (Nonaka & Takeuchi, 1995) and thus forms an essential part of the knowledge management process. The understanding of how knowledge is transferred is very important for explaining the evolution and change in institutions, organisations, technology, and economy. However, knowledge transfer is often found to be laborious, time consuming, complicated, and difficult to understand (Huber, 2001; Szulanski, 2000). It has received negligible systematic attention (Huber, 2001; Szulanski, 2000), thus we know little about it (Huber, 2001). However, some literature, such as Davenport and Prusak (1998) and Shariq (1999), has attempted to address knowledge transfer within an organisation, but studies on inter-organisational knowledge transfer are still much neglected. An emergent view is that it may be beneficial for organisations if more research can be done to help them understand and, thus, to improve their inter-organisational knowledge transfer process. Therefore, this article aims to provide an overview of the inter-organisational knowledge transfer and its related literature and present a proposed inter-organisational knowledge transfer process model based on theoretical and empirical studies.

What does endogenous growth theory tell about regional economies? Empirics of R&D worker-based productivity growth

What does endogenous growth theory tell about regional economies? Empirics of R&D worker-based productivity growth, Regional Studies. Endogenous growth theory emerged in the 1990s as ‘new growth theory’ accounting for technical progress in the growth process. This paper examines the role of research and development (R&D) workers underlying the Romer model (1990) and its subsequent modifications, and compares it with a model based on the accumulation of human capital engaged in R&D. Cross-section estimates of the models against productivity growth of European regions in the 1990s suggest that each R&D worker has a unique set of knowledge while his/her contributions are enhanced by knowledge sharing within a region as well as spillovers from other regions in proximity.

Does role clarity explain employee-perceived service quality? A study of antecedents and consequences in call centres

Purpose – Role clarity of frontline staff is critical to their perceptions of service quality in call centres. The purpose of this study is to examine the effects of role clarity and its antecedents and consequences on employee-perceived service quality. Design/methodology/approach – A conceptual model, based on the job characteristics model and cognitive theories, is proposed. Key antecedents of role clarity considered here are feedback, autonomy, participation, supervisory consideration, and team support; while key consequences are organizational commitment, job satisfaction and service quality. An internal marketing approach is adopted and all variables are measured from the frontline employee's perspective. A structural equation model is developed and tested on a sample of 342 call centre representatives of a major commercial bank in the UK. Findings – The research reveals that role clarity plays a critical role in explaining employee perceptions of service quality. Further, the research findings indicate that feedback, participation and team support significantly influence role clarity, which in turn influences job satisfaction and organizational commitment. Research limitations/implications – The research suggests that boundary personnel in service firms should strive for more clarity in perceived role for delivering better service quality. The limitations are in sample availability from in-house transaction call centres of a single bank. Originality/value – The contributions of this study are untangling the confusing research evidence on the effect of role clarity on service quality, using service quality as a performance variable as opposed to productivity estimates, adopting an internal marketing approach to understanding the phenomenon, and introducing teamwork along with job-design and supervisory factors as antecedent to role clarity.

Mach edges: a critical test of the nonlinear 3rd derivative model for edge-detection

Feature detection is a crucial stage of visual processing. In previous feature-marking experiments we found that peaks in the 3rd derivative of the luminance profile can signify edges where there are no 1st derivative peaks nor 2nd derivative zero-crossings (Wallis and George 'Mach edges' (the edges of Mach bands) were nicely predicted by a new nonlinear model based on 3rd derivative filtering. As a critical test of the model, we now use a new class of stimuli, formed by adding a linear luminance ramp to the blurred triangle waves used previously. The ramp has no effect on the second or higher derivatives, but the nonlinear model predicts a shift from seeing two edges to seeing only one edge as the added ramp gradient increases. In experiment 1, subjects judged whether one or two edges were visible on each trial. In experiment 2, subjects used a cursor to mark perceived edges and bars. The position and polarity of the marked edges were close to model predictions. Both experiments produced the predicted shift from two to one Mach edge, but the shift was less complete than predicted. We conclude that the model is a useful predictor of edge perception, but needs some modification.

Canonical solution groups of a homomorphism : manipulator kinematics, nonparametric regression and distributed object systems

The kinematic mapping of a rigid open-link manipulator is a homomorphism between Lie groups. The homomorphisrn has solution groups that act on an inverse kinematic solution element. A canonical representation of solution group operators that act on a solution element of three and seven degree-of-freedom (do!) dextrous manipulators is determined by geometric analysis. Seven canonical solution groups are determined for the seven do! Robotics Research K-1207 and Hollerbach arms. The solution element of a dextrous manipulator is a collection of trivial fibre bundles with solution fibres homotopic to the Torus. If fibre solutions are parameterised by a scalar, a direct inverse funct.ion that maps the scalar and Cartesian base space coordinates to solution element fibre coordinates may be defined. A direct inverse pararneterisation of a solution element may be approximated by a local linear map generated by an inverse augmented Jacobian correction of a linear interpolation. The action of canonical solution group operators on a local linear approximation of the solution element of inverse kinematics of dextrous manipulators generates cyclical solutions. The solution representation is proposed as a model of inverse kinematic transformations in primate nervous systems. Simultaneous calibration of a composition of stereo-camera and manipulator kinematic models is under-determined by equi-output parameter groups in the composition of stereo-camera and Denavit Hartenberg (DH) rnodels. An error measure for simultaneous calibration of a composition of models is derived and parameter subsets with no equi-output groups are determined by numerical experiments to simultaneously calibrate the composition of homogeneous or pan-tilt stereo-camera with DH models. For acceleration of exact Newton second-order re-calibration of DH parameters after a sequential calibration of stereo-camera and DH parameters, an optimal numerical evaluation of DH matrix first order and second order error derivatives with respect to a re-calibration error function is derived, implemented and tested. A distributed object environment for point and click image-based tele-command of manipulators and stereo-cameras is specified and implemented that supports rapid prototyping of numerical experiments in distributed system control. The environment is validated by a hierarchical k-fold cross validated calibration to Cartesian space of a radial basis function regression correction of an affine stereo model. Basic design and performance requirements are defined for scalable virtual micro-kernels that broker inter-Java-virtual-machine remote method invocations between components of secure manageable fault-tolerant open distributed agile Total Quality Managed ISO 9000+ conformant Just in Time manufacturing systems.