A micro gas turbines for UK domestic combined heat and power

Various micro-radial compressor configurations were investigated using one-dimensional meanline and computational fluid dynamics (CFD) techniques for use in a micro gas turbine (MGT) domestic combined heat and power (DCHP) application. Blade backsweep, shaft speed, and blade height were varied at a constant pressure ratio. Shaft speeds were limited to 220 000 r/min, to enable the use of a turbocharger bearing platform. Off-design compressor performance was established and used to determine the MGT performance envelope; this in turn was used to assess potential cost and environmental savings in a heat-led DCHP operating scenario within the target market of a detached family home. A low target-stage pressure ratio provided an opportunity to reduce diffusion within the impeller. Critically for DCHP, this produced very regular flow, which improved impeller performance for a wider operating envelope. The best performing impeller was a low-speed, 170 000 r/min, low-backsweep, 15° configuration producing 71.76 per cent stage efficiency at a pressure ratio of 2.20. This produced an MGT design point system efficiency of 14.85 per cent at 993 W, matching prime movers in the latest commercial DCHP units. Cost and CO2 savings were 10.7 per cent and 6.3 per cent, respectively, for annual power demands of 17.4 MWht and 6.1 MWhe compared to a standard condensing boiler (with grid) installation. The maximum cost saving (on design point) was 14.2 per cent for annual power demands of 22.62 MWht and 6.1 MWhe corresponding to an 8.1 per cent CO2 saving. When sizing, maximum savings were found with larger heat demands. When sized, maximum savings could be made by encouraging more electricity export either by reducing household electricity consumption or by increasing machine efficiency.

Determination of muscle fatigue in clinical practices using dynamically embedded signals

This paper explores a new method of analysing muscle fatigue within the muscles predominantly used during microsurgery. The captured electromyographic (EMG) data retrieved from these muscles are analysed for any defining patterns relating to muscle fatigue. The analysis consists of dynamically embedding the EMG signals from a single muscle channel into an embedded matrix. The muscle fatigue is determined by defining its entropy characterized by the singular values of the dynamically embedded (DE) matrix. The paper compares this new method with the traditional method of using mean frequency shifts in the EMG signal's power spectral density. Linear regressions are fitted to the results from both methods, and the coefficients of variation of both their slope and point of intercept are determined. It is shown that the complexity method is slightly more robust in that the coefficient of variation for the DE method has lower variability than the conventional method of mean frequency analysis.

A smart sensing platform for the classification of ambulatory patterns

This paper describes an innovative sensing approach allowing capture, discrimination, and classification of transients automatically in gait. A walking platform is described, which offers an alternative design to that of standard force plates with advantages that include mechanical simplicity and less restriction on dimensions. The scope of the work is to investigate as an experiment the sensitivity of the distributive tactile sensing method with the potential to address flexibility on gait assessment, including patient targeting and the extension to a variety of ambulatory applications. Using infrared sensors to measure plate deflection, gait patterns are compared with stored templates using a pattern recognition algorithm. This information is input into a neural network to classify normal and affected walking events, with a classification accuracy of just under 90 per cent achieved. The system developed has potential applications in gait analysis and rehabilitation, whereby it can be used as a tool for early diagnosis of walking disorders or to determine changes between pre- and post-operative gait.

Examining the information and communication technologies enabling servitized manufacture

Services-led competitive strategies are critically important to Western manufacturers. This paper contributes to our basic knowledge of such strategies by examining the enabling information and communication technologies that successfully servitized manufacturers appear to be adopting. Although these are preliminary findings from a longer-term research programme, through this paper we seek to offer immediate assistance to manufacturers who wish to understand how they might exploit the servitization movement.

State-of-the-art in integrated vehicle health management

Integrated vehicle health management (IVHM) is a collection of data relevant to the present and future performance of a vehicle system and its transformation into information can be used to support operational decisions. This design and operation concept embraces an integration of sensors, communication technologies, and artificial intelligence to provide vehicle-wide abilities to diagnose problems and recommend solutions. This article aims to report the state-of-the-art of IVHM research by presenting a systematic review of the literature. The literature from different sources is collated and analysed, and the major emerging themes are presented. On this basis, the article describes the IVHM concept and its evolution, discusses configurations and existing applications along with main drivers, potential benefits and barriers to adoption, summarizes design guidelines and available methods, and identifies future research challenges.

Beyond theory:an examination of lean new product introduction practices in the UK

Interest is growing around the application of lean techniques to new product introduction (NPI). Although a relatively emergent topic compared with the application of ‘lean’ within the factory, since 2000 there has been an exponential rise in the literature on this subject. However, much of this work focuses on describing and extolling the virtues of the ‘Toyota approach’ to design. Therefore, by way of a stock take for the UK, the present authors' research has set out to understand how well lean product design practices have been adopted by leading manufacturers. This has been achieved by carrying out in-depth case studies with three carefully selected manufacturers of complex engineered products. This paper describes these studies, the detailed results and subsequent findings, and concludes that both the awareness and adoption of practices is generally embryonic and far removed from the theory advocated in the literature.

State-of-the-art in product-service systems

A Product-Service System (PSS) is an integrated combination of products and services. This Western concept embraces a service-led competitive strategy, environmental sustainability, and the basis to differentiate from competitors who simply offer lower priced products. This paper aims to report the state-of-the-art of PSS research by presenting a clinical review of literature currently available on this topic. The literature is classified and the major outcomes of each study are addressed and analysed. On this basis, this paper defines the PSS concept, reports on its origin and features, gives examples of applications along with potential benefits and barriers to adoption, summarizes available tools and methodologies, and identifies future research challenges.

State-of-the-art in lean design engineering:a literature review on white collar lean

Lean is usually associated with the ‘operations’ of a manufacturing enterprise; however, there is a growing awareness that these principles may be transferred readily to other functions and sectors. The application to knowledge-based activities such as engineering design is of particular relevance to UK plc. Hence, the purpose of this study has been to establish the state-of-the-art, in terms of the adoption of Lean in new product development, by carrying out a systematic review of the literature. The authors' findings confirm the view that Lean can be applied beneficially away from the factory; that an understanding and definition of value is key to success; that a set-based (or Toyota methodology) approach to design is favoured together with the strong leadership of a chief engineer; and that the successful implementation requires organization-wide changes to systems, practices, and behaviour. On this basis it is felt that this review paper provides a useful platform for further research in this topic.

Servitization within manufacturing operations:an exploration of the impact to facilities practices

Servitization is a growing area of interest amongst practitioners, policymakers, and academics, and much is still to be learnt about its adoption in practice. This paper makes a contribution to this debate by identifying the key facilities practices that successful servitizing manufacturers appear to be deploying, and the underlying rationale behind their configuration. Although these are preliminary findings from a longer-term research programme, this short communication seeks to highlight the implications for manufacturing professionals and organizations who are considering the servitization of their operations.

The adoption of servitization strategies by UK-based manufacturers

Almost all manufacturers offer services, but some use these as the basis for their competitive strategy. This is a growing area of interest among practitioners, policy makers, and academics, yet little is known about the adoption of servitization by UK manufacturers. In this paper a survey is presented that has been used to explore the extent, motivations, challenges, and successes of servitization within the business-to-business sector. The findings indicate, for example, that many manufacturers are succeeding with their service strategies, that they are attracted to these as a source of customer focus and revenue growth, and that such strategies require less organizational change than might be expected. Although the findings from the survey should be treated as preliminary, and further work is needed to confirm their reliability and insight, they indicate that servitization is proving to be a powerful competitive weapon for many companies.

State-of-the-art of ‘Lean’ in the aviation maintenance, repair, and overhaul industry

The increasing need for maintenance, repair, and overhaul (MRO) organizations to meet customers' demands in quality and reduced lead times is key to its survival within the aviation industry. Furthermore, with the unpredictability in the global market and difficulties with forecasting characteristic of the MRO industry there is an increased need for the reevaluation of the operation models of organizations within this sector. However, severe economic turmoil and ever-increasing global competition introduce the opportunity for the adoption of a resilient, tried, and tested business operation model such as 'Lean'. In order to understand this concept, its long-term viability, and its application within the aerospace MRO sector fully, this paper presents the state-of-the-art in terms of the adoption of Lean within the MRO industry by carrying out a systematic review of the literature. This paper establishes the common perception of Lean by the MRO industry and the measurable progress that has been made on the subject. Some issues and challenges are also highlighted including the misconceptions that arise from the direct transference of the perception of Lean from other industrial sectors into the aerospace MRO industry. The 'enablers and inhibitors' of Lean within the aviation industry are also discussed. This paper exposes the scarcity of the literature and the general lagging behind of the industry to the adoption of the Lean paradigm and thus highlights areas where further research is required. © 2011 Authors.

An exploration of policies and practices used to showcase production facilities

Manufacturers who seek innovative ways in which to differentiate their products and services should not overlook the value of showcasing their production facilities. By careful design, visitors can be exposed to a series of experiences that can help to emphasize the value built into products. This topic has, however, received almost no attention by manufacturing researchers. Therefore, this paper describes a study of six manufacturers and, from this, proposes a set of guidelines for showcasing production facilities. Although exploratory, this work provides both a guide to manufacturers and a platform for more in-depth research. The guidelines and the case studies on which they are based are all described within the paper.

Strategic positioning of manufacturing operations within global supply chains

This paper describes research that has sought to create a structured and integrated methodology that guides manufacturers through the decision of strategic positioning within global supply chains. The position of a company is concerned with deciding a boundary and configuration of internal and external business activities to the company and is directly related to initiatives such as outsourcing, make or buy, and offshoring. This paper provides an in-depth description of this concept, describes work carried out to form a methodology for strategic positioning within the global supply chain, and presents the details of the methodology. This research has made a significant contribution to the knowledge on how manufacturing companies can form a strategic positioning within global supply chains.

Crack-growth of medical-grade silicone using pure shear tests

Silicone elastomers are commonly used in the manufacture of single-piece joint replacement implants for the finger joints. However, the survivorship of these implants can be poor, with failure typically occurring from fracture of the stems. The aim of this paper was to investigate the crack growth of medical-grade silicone using pure shear tests. Two medical-grade silicones (C6-180 and Med82-5010-80) were tested. Each sample had a 20 mm crack introduced and was subjected to a sinusoidally varying tensile strain, with a minimum of 0 per cent and a maximum in the range 10 to 77 per cent. Testing was undertaken at a frequency of 10 Hz. At various times during testing, the testing machine was stopped, the number of cycles completed was noted, and the crack length measured. Graphs of crack length against number of cycles were plotted, as well as the crack growth rate against tearing energy. The results show that Med82-5010-80 is more crack resistant than C6-180. Graphs of crack growth rate against tearing energy can be used to predict the failure of these medical-grade elastomers.