Micromechanics of agglomerate damage processes

This thesis reports a detailed investigation of the micromechanics of agglomerate behaviour under free-fall impact, double (punch) impact and diametrical compression tests using the simulation software TRUBAL. The software is based on the discrete element method (DEM) which incorporates the Newtonian equations of motion and contact mechanics theory to model the interparticle interactions. Four agglomerates have been used: three dense (differing in interface energy and contact density) and one loose. Although the simulated agglomerates are relatively coarse-grained, the results obtained are in good agreement with laboratory test results reported in the literature. The computer simulation results show that, in all three types of test, the loose agglomerate cannot fracture as it is unable to store sufficient elastic energy. Instead, it becomes flattened for low loading-rates and shattered or crushed at higher loading-rates. In impact tests, the dense agglomerates experience only local damage at low impact velocities. Semi-brittle fracture and fragmentation are produced over a range of higher impact velocities and at very high impact velocities shattering occurs. The dense agglomerates fracture in two or three large fragments in the diametrical compression tests. Local damage at the agglomerate-platen interface always occurs prior to fracture and consists of local bond breakage (microcrack formation) and local dislocations (compaction). The fracture process is dynamic and much more complex than that suggested by continuum fracture mechanics theory. Cracks are always initiated from the contact zones and propagate towards the agglomerate centre. Fracture occurs a short time after the start of unloading when a fracture crack "selection" process takes place. The detailed investigation of the agglomerate damage processes includes an examination of the evolution of the fracture surface. Detailed comparisons of the behaviour of the same agglomerate in all three types of test are presented. The particle size distribution curves of the debris are also examined, for both free-fall and double impact tests.

Incorporating Water Sensitive Urban Design (WSUD) practices into the planning context:the conceptual case for lot-scale developments

In recent decades, a number of sustainable strategies and polices have been created to protect and preserve our water environments from the impacts of growing communities. The Australian approach, Water Sensitive Urban Design (WSUD), defined as the integration of urban planning and design with the urban water cycle management, has made considerable advances on design guidelines since 2000. WSUD stormwater management systems (e.g. wetlands, bioretentions, porous pavement etc), also known as Best Management Practices (BMPs) or Low Impact Development (LID), are slowly gaining popularity across Australia, the USA and Europe. There have also been significant improvements in how to model the performance of the WSUD technologies (e.g. MUSIC software). However, the implementation issues of these WSUD practices are mainly related to ongoing institutional capacity. Some of the key problems are associated with a limited awareness of urban planners and designers; in general, they have very little knowledge of these systems and their benefits to the urban environments. At the same time, hydrological engineers should have a better understanding of building codes and master plans. The land use regulations are equally as important as the physical site conditions for determining opportunities and constraints for implementing WSUD techniques. There is a need for procedures that can make a better linkage between urban planners and WSUD engineering practices. Thus, this paper aims to present the development of a general framework for incorporating WSUD technologies into the site planning process. The study was applied to lot-scale in the Melbourne region, Australia. Results show the potential space available for fitting WSUD elements, according to building requirements and different types of housing densities. © 2011 WIT Press.

Fibre optic sensors for high speed hypervelocity impact studies and low velocity drop tests

The initial aim of this project was to develop a non-contact fibre optic based displacement sensor to operate in the harsh environment of a 'Light Gas Gun' (LGG), which can 'fire' small particles at velocities ranging from 1-8.4 km/s. The LGG is used extensively for research in aerospace to analyze the effects of high speed impacts on materials. Ideally the measurement should be made close to the centre of the impact to minimise corruption of the data from edge effects and survive the impact. A further requirement is that it should operate at a stand-off distance of ~ 8cm. For these reasons we chose to develop a pseudo con-focal intensity sensor, which demonstrated resolution comparable with conventional PVDF sensors combined with high survivability and low cost. A second sensor was developed based on 'Fibre Bragg Gratings' (FBG) which although requiring contact with the target the low weight and very small contact area had minimal effect on the dynamics of the target. The FBG was mounted either on the surface of the target or tangentially between a fixed location. The output signals from the FBG were interrogated in time by a new method. Measurements were made on composite and aluminium plates in the LGG and on low speed drop tests. The particle momentum for the drop tests was chosen to be similar to that of the particles used in the LGG.

Fibre optic sensors for high speed hypervelocity impact studies and low velocity drop tests

The initial aim of this project was to develop a non-contact fibre optic based displacement sensor to operate in the harsh environment of a 'Light Gas Gun' (LGG), which can 'fire' small particles at velocities ranging from 1-8.4 km/s. The LGG is used extensively for research in aerospace to analyze the effects of high speed impacts on materials. Ideally the measurement should be made close to the centre of the impact to minimise corruption of the data from edge effects and survive the impact. A further requirement is that it should operate at a stand-off distance of ~ 8cm. For these reasons we chose to develop a pseudo con-focal intensity sensor, which demonstrated resolution comparable with conventional PVDF sensors combined with high survivability and low cost. A second sensor was developed based on 'Fibre Bragg Gratings' (FBG) which although requiring contact with the target the low weight and very small contact area had minimal effect on the dynamics of the target. The FBG was mounted either on the surface of the target or tangentially between a fixed location. The output signals from the FBG were interrogated in time by a new method. Measurements were made on composite and aluminium plates in the LGG and on low speed drop tests. The particle momentum for the drop tests was chosen to be similar to that of the particles used in the LGG.

The impact of foreign direct investment on UK manufacturing: is there a profit squeeze in domestic firms?

This paper examines the extent to which foreign direct investment (FDI) in selected UK manufacturing sectors has an impact on reported profits in domestic firms. Foreign manufacturing firms are characterized by relatively high labour productivity and low wage shares. Entry by foreign firms not only impacts on domestic market shares, but also on domestic cost conditions. As a result, profitability in the indigenous sector may be reduced. There are a number of policy implications of this analysis which are explored.

Impact of the length of relationships upon the use of research institutes by SMEs

Recent studies of US industrial modernisation programmes argue that difficulties of establishing long-term relationships with users prevent them from facilitating development of innovation capabilities. The paper supports this argument through a survey of Japanese research institutes the US programmes were modelled on. In view of information asymmetries in their use, it tests the hypothesis that small and medium-sized firms start using the research institutes with ‘low information gap’ services and gradually move on to ‘high information gap’ services that often require more absorptive capacity. This is demonstrated both under one-to-one relationships and between groups of firms and a research institute.

Investigation of the effects of low energy high dose ion bombardment in metals and compound semiconductors

The effect of low energy nitrogen molecular ion beam bombardment on metals and compound semiconductors has been studied, with the aim to investigate at the effects of ion and target properties. For this purpose, nitrogen ion implantation in aluminium, iron, copper, gold, GaAs and AIGaAs is studied using XPS and Angle Resolve XPS. A series of experimental studies on N+2 bombardment induced compositional changes, especially the amount of nitrogen retained in the target, were accomplished. Both monoenergetic implantation and non-monoenergetic ion implantation were investigated, using the VG Scientific ESCALAB 200D system and a d. c. plasma cell, respectively. When the samples, with the exception of gold, are exposed to air, native oxide layers are formed on the surfaces. In the case of monoenergetic implantation, the surfaces were cleaned using Ar+ beam bombardment prior to implantation. The materials were then bombarded with N2+ beam and eight sets of successful experiments were performed on each sample, using a rastered N2+ ion beam of energy of 2, 3, 4 and 5 keV with current densities of 1 μA/cm2 and 5 μA/cm22 for each energy. The bombarded samples were examined by ARXPS. After each complete implantation, XPS depth profiles were created using Ar+ beam at energy 2 ke V and current density 2 μA/cm2 . As the current density was chosen as one of the parameters, accurate determination of current density was very important. In the case of glow discharge, two sets of successful experiments were performed in each case, by exposing the samples to nitrogen plasma for the two conditions: at low pressure and high voltage and high pressure and low voltage. These samples were then examined by ARXPS. On the theoretical side, the major problem was prediction of the number of ions of an element that can be implanted in a given matrix. Although the programme is essentially on experimental study, but an attempt is being made to understand the current theoretical models, such as SATVAL, SUSPRE and TRIM. The experimental results were compared with theoretical predictions, in order to gain a better understanding of the mechanisms responsible. From the experimental results, considering possible experimental uncertainties, there is no evidence of significant variation in nitrogen saturation concentration with ion energy or ion current density in the range of 2-5 ke V, however, the retention characteristics of implantant seem to strongly depend on the chemical reactivity between ion species and target material. The experimental data suggests the presence of at least one thermal process. The discrepancy between the theoretical and experimental results could be the inability of the codes to account for molecular ion impact and thermal processes.

A detailed study of the mechanical and electrical aspects of microparticle impact phenomena

An experimental and theoretical study of the impact behaviour of charged microparticles in a high voltage vacuum gap has been carried out to investigate under controlled conditions the role of low velocity microparticles (ζ 500 ms-1) in initiating electrical breakdown in such gaps. This has involved developing a unique (UHV) low-velocity source of micron-sized charged particles to study the underlying mechanical and electrical aspects of micro-particle impact on a range of target materials e.g. Pb, Ti, C, stainless-steel and mica etc., having atomically clean or oxidised surfaces. Argon-ion etching and electron-beam heating has been used for in-situ surface treatment and ellipsometry for characterising the target surfaces. An associated sphere/plane theoretical model has been developed for detailed analysis of the many complex electrical (in-flight in-field emission, M.I.M. tunnelling and ohmic conduction) and mechanical (impact dynamics, deformation and heating) phenomena that are involved when a microparticle closely approaches and impacts on a plane target. In each instance the influence of parameters such as particle radius, particle/target impact velocity, surface field, surface condition and material has been determined.

The impact of the language barrier on the management of multinational companies : a case study and survey, based exploration of the impact of the language barrier on the strategies, policies and systems by which multinational companies manage their subsidaries

The thesis begins with a conceptual model of the way that language diversity affects the strategies, organisation and subsidiary control policies of multinational companies. The model is based solely on the researcher'’ personal experience of working in a variety of international management roles, but in Chapter 2 a wide-ranging review of related academic literature finds evidence to support the key ideas. The model is developed as a series of propositions which are tested in a comparative case study, refined and then re-tested in a global survey of multinational subsidiaries. The principal findings of the empirical phases of the thesis endorse the main tenets of the model: - That language difference between parent and subsidiary will impair communication, create mistrust and impede relationship development. - That subsequently the feelings of uncertainty, suspicion and mistrust will influence the decisions taken by the parent company. - They will have heightened sensitivity to language issues and will implement policies to manage language differences. - They will adopt low-risk strategies in host countries where they are concerned about language difference. - They will use organisational and manpower strategies to minimise the consequences and risks of the communications problems with the subsidiary. - As a consequence the level of integration and knowledge flow between parent and subsidiary will be curtailed. - They will adopt styles of control that depend least on their ability to communicate with their subsidiary. Although there is adequate support for all of the above conclusions, on some key points the evidence of the Case Studies and Survey is contradictory. The thesis, therefore, closes with an agenda for further research that would address these inconsistencies.

The impact of drug information on the prescribing of drugs

Using prescription analyses and questionnaires, the way drug information was used by general medical practitioners during the drug adoption process was studied. Three new drugs were considered; an innovation and two 'me-too' products. The innovation was accepted by general practitioners via a contagion process, information passing among doctors. The 'me-too' preparations were accepted more slowly and by a process which did not include the contagion effect. 'Industrial' information such as direct mail was used more at the 'awareness' stage of the adoption process while 'professional' sources of information such as articles in medical journals were used more to evaluate a new product. It was shown that 'industrial' information was preferred by older single practice doctors who did not specialise, had a first degree only and who did not dispense their own prescriptions. Doctors were divided into early and late-prescribers by using the date they first prescribed the innovatory drug. Their approach to drug information sources was further studied and it was shown that the early-prescriber issued slightly more prescriptions per month, had a larger list size, read fewer journals and generally rated industrial sources of information more highly than late-prescribers. The prescribing habits of three consultant rheumatologists were analysed and compared with those of the general practitioners in the community which they served. Very little association was noted and the influence of the consultant on the prescribing habits of general practitioners was concluded to be low. The consultants influence was suggested to be of two components, active and passive; the active component being the most influential. Journal advertising and advertisement placement were studied for one of the 'me-too' drugs. It was concluded that advertisement placement should be based on the reading patterns of general practitioners and not on ad-hoc data gathered by representatives as was the present practice. A model was proposed relating the 'time to prescribe' a new drug to the variables suggested throughout this work. Four of these variables were shown to be significant. These were, the list size, the medical age of the prescriber, the number of new preparations prescribed in a given time and the number of partners in the practice.

How does bureaucracy impact individual creativity? A cross-level investigation of team contextual influences on goal orientation-creativity relationships

Offering important counterpoint to work identifying team influences stimulating creative expression of individual differences in goal orientation, we develop cross-level theory establishing that team bureaucratic practices (centralization and formalization) constrain creative expression. Speaking to the tension between bureaucracy and creativity, findings indicate that this influence is not only negative and that effects of centralization and formalization differ. Surveying 330 employees in 95 teams at the Taiwan Customs Bureau, we found that learning and "performance avoid" goal orientations had, respectively, stronger positive and weaker negative relationships with creativity under low centralization. A "performance- prove" orientation was positively related to creativity under low formalization. © Academy of Management Journal.

The impact of relational demography on the quality of leader-member exchanges and employees' work attitudes and well-being

This study investigated the role of differences in age, organizational tenure and gender between manager and employee as potential moderators between employees' leader-member exchanges (LMX) and related work outcomes. The results support the interaction effect of manager-employee organizational tenure difference with LMX and outcome variables. Employees with a high organizational tenure difference from the manager reported the worst work outcomes when they perceived LMX was of low quality, whereas when the quality of LMX was high, they reported the highest work attitudes and well-being.

Impact of power allocation strategies in long-haul few-mode fiber transmission systems

We report for the first time on the limitations in the operational power range of few-mode fiber based transmission systems, employing 28Gbaud quadrature phase shift keying transponders, over 1,600km. It is demonstrated that if an additional mode is used on a preexisting few-mode transmission link, and allowed to optimize its performance, it will have a significant impact on the pre-existing mode. In particular, we show that for low mode coupling strengths (weak coupling regime), the newly added variable power mode does not considerably impact the fixed power existing mode, with performance penalties less than 2dB (in Q-factor). On the other hand, as mode coupling strength is increased (strong coupling regime), the individual launch power optimization significantly degrades the system performance, with penalties up to ∼6dB. Our results further suggest that mutual power optimization, of both fixed power and variable power modes, reduces power allocation related penalties to less than 3dB, for any given coupling strength, for both high and low differential mode delays. © 2013 Optical Society of America.

Modeling impact of both frame collisions and frame corruptions on IEEE 802.15.4 channel access for smart grid applications

IEEE 802.15.4 standard has been recently developed for low power wireless personal area networks. It can find many applications for smart grid, such as data collection, monitoring and control functions. The performance of 802.15.4 networks has been widely studied in the literature. However the main focus has been on the modeling throughput performance with frame collisions. In this paper we propose an analytic model which can model the impact of frame collisions as well as frame corruptions due to channel bit errors. With this model the frame length can be carefully selected to improve system performance. The analytic model can also be used to study the 802.15.4 networks with interference from other co-located networks, such as IEEE 802.11 and Bluetooth networks. © 2011 Springer-Verlag.