The automation of resonant thermometer probe measurements

An ultrasonic thermometer has been developed for high temperature measurement over a wide temperature range. It is particularly suitable for use in measuring nuclear fuel rod centerline temperatures in advanced liquid metal and high flux nuclear reactors. The thermometer which was designed to determine fuel temperature up to the fuel melting point, utilizes the temperature dependence of the ultrasonic propagation velocity (related to the elastic modulus} in a thin rod sensor as the temperature transducing mechanism. A pulse excitation technique has been used, where the mechanical resonator at the remote end of the acoustic·line is madto vibrate. Its natural frequency is proportional to the ultrasonic velocity in the material. This is measured by the electronic instrumentation and enables a frequency­ temperature or period-temperature calibration to be obtained. A completely digital automatic instrument has been designed, constructed and tested to track the resonance frequency of the temperature sensors. It operates smoothly over a frequency range of about 30%, more than the maximum working range of most probe materials. The control uses the basic property of a resonator that the stored energy decays exponentially at the natural frequency of the resonator.The operation of the electronic system is based on a digital multichannel transmitter that is capable of operating with a predefined number of cycles in the burst. this overcomes a basic defect in the previous deslgn where the analogue time-delayed circuits failed to hold synchronization and hence automatic control could be lost. Development of a particular type of temperature probe, that is small enough to fit into a standard 2 mm reactor tube has made the ultrasonic thermometer a practicable device for measuring fuel temperature. The bulkiness of previous probes has been overcome, the new design consists of a tuning fork, integral with a 1mm line, while maintaining a frequency of no more than 100 kHz. A magnetostrictive rod, acoustically matched to the probe is used to launch and receive the acoustic oscillations. This requires a magnetic bias and the previously used bulky magnets have been replaced by a direct current coil. The probe is supported by terminating the launcher with a short heavy isolating rod which can be secured to the reactor structure. This support, the bias and launching coil and the launcher are made up into a single compact unit. On the material side an extensive study of a wide range of refractory materials identified molybdenum, iridium, rhenium and tungsten as satisfactory for a number of applications but mostly exhibiting to some degree a calibration drift with thermal cycling. When attention was directed to ceramic materials, Sapphire (single crystal alumina) was found to have numerous advantages, particularly in respect of stability of calibration which remained with ±2°C after many cycles to 1800oC. Tungsten and thoriated tungsten (W - 2% Tho2) were also found to be quite satisfactory to 1600oC, the specification for a Euratom application.

The fatigue properties of pressure diecast zinc-aluminium based alloys

The fatigue behaviour of the cold chamber pressure-die-cast alloys: Mazak3, ZA8, ZA27, M3K, ZA8K, ZA27K, K1, K2 and K3 was investigated at temperature of 20°C. The alloys M3K, ZA8K and ZA27K were also examined at temperatures of 50 and 100°C. The ratio between fatigue strength and tensile strength was established at 20°C at 107 cycles. The fatigue life prediction of the alloys M3K, ZA8K and ZA27K was formulated at 20, 50 and 100°C. The prediction formulae were found to be reasonably accurate. All of the experimental alloys were heterogeneous and contained large but varying amounts of pores. These pores were a major contribution and dominated the alloys fatigue failure. Their effect, however, on tensile failure was negligible. The ZA27K possessed the highest tensile strength but the lowest fatigue strength. The relationship between the fracture topography and the microstructure was also determined by the use of a mixed signal of a secondary electron and a back-scattered electron on the SEM. The tensile strength of the experimental alloys was directly proportional to the aluminium content within the alloys. The effect of copper content was also investigated within the alloys K1, K2, ZA8K and K3 which contained 0%, 0.5%, 1.0% and 2.0% respectively. It was determined that the fatigue and tensile strengths improved with higher copper contents. Upon ageing the alloys Mazak3, ZA8 and ZA27 at an ambient temperature for 5 years, copper was also found to influence and maintain the metastable Zn-Al (αm) phase. The copper free Mazak3 upon ageing lost this metastable phase. The 1.0% copper ZA8 alloy had lost almost 50% of its metastable phase. Finally the 2.0% copper ZA27 had merely lost 10% of its metastable phase. The cph zinc contained a limited number of slip systems, therefore twinning deformation was unavoidable in both fatigue and tensile testing.

An analysis of penalty kicks in elite football post 1997

The penalty kick in football is a seemingly simplistic play; however, it has increased in complexity since 1997 when the rules changed allowing goalkeepers to move laterally along their goal line before the ball was kicked. Prior to 1997 goalkeepers were required to remain still until the ball was struck. The objective of this study was to determine the importance of the penalty kick in the modern game of football. A retrospective study of the 2002, 2006 and 2010 World Cup and the 2000, 2004 and 2008 European Championship tournaments was carried out, assessing the importance of the penalty kick in match play and shootouts and the effect of the time of the game on the shooter's success rate. This study demonstrated the conversion rate of penalties was 73% in shootouts and 68% in match play. Significantly more penalties were awarded late in the game: twice as many penalties in the second half than the first and close to four times as many in the fourth quarter vs. the first. Teams awarded penalty kicks during match play won 52%, drew 30% and lost 18% of the time; chances of winning increased to 61% if the penalty was scored, but decreased to 29% if missed. Teams participating in either the World Cup or European Championship final match had roughly a 50% chance of being involved in a penalty shootout during the tournament. Penalty shots and their outcome significantly impact match results in post 1997 football.

Paradox lost? Exploring the role of alpha oscillations during externally vs. internally directed attention and the implications for idling and inhibition hypotheses

Although slow waves of the electroencephalogram (EEG) have been associated with attentional processes, the functional significance of the alpha component in the EEG (8.1–12 Hz) remains uncertain. Conventionally, synchronisation in the alpha frequency range is taken to be a marker of cognitive inactivity, i.e. ‘cortical idling’. However, it has been suggested that alpha may index the active inhibition of sensory information during internally directed attentional tasks such as mental imagery. More recently, this idea has been amended to encompass the notion of alpha synchronisation as a means of inhibition of non-task relevant cortical areas irrespective of the direction of attention. Here we test the adequacy of the one idling and two inhibition hypotheses about alpha. In two experiments we investigated the relation between alpha and internally vs. externally directed attention using mental imagery vs. sensory-intake paradigms. Results from both experiments showed a clear relationship between alpha and both attentional factors and increased task demands. At various scalp sites alpha amplitudes were greater during internally directed attention and during increased load, results incompatible with alpha reflecting cortical idling and more in keeping with suggestions of active inhibition necessary for internally driven mental operations.

Hijacked then lost in translation:the plight of the recombinant host cell in membrane protein structural biology projects

Membrane protein structural biology is critically dependent upon the supply of high-quality protein. Over the last few years, the value of crystallising biochemically characterised, recombinant targets that incorporate stabilising mutations has been established. Nonetheless, obtaining sufficient yields of many recombinant membrane proteins is still a major challenge. Solutions are now emerging based on an improved understanding of recombinant host cells; as a 'cell factory' each cell is tasked with managing limited resources to simultaneously balance its own growth demands with those imposed by an expression plasmid. This review examines emerging insights into the role of translation and protein folding in defining high-yielding recombinant membrane protein production in a range of host cells.