Solid bridge formation between spray-dried sodium carbonate particles

Moisture migration caking of pharmaceutical excipients in the absence of load is a significant quality and stability issue. This study uses Atomic Force Microscopy (AFM) to examine a solid bridge formed between two 20µm spray-dried sodium carbonate particles. The bridge is grown by repeatedly exposing the system to 70% RH and 30% RH cycles at 25?C. A comparison is made with the idealised bridge model developed by Tanaka (1978) which was previously verified using crystalline systems. The resulting system was found to be more complex and grew in two stages. The first stage consisted of linear growth to 5 cycles, followed by a more gradual expansion and the appearance of crystalline structures.

Technical efficiency:efficiency, change, technical progress and productivity growth in the national health systems of continental African countries

In May 2006, the Ministers of Health of all the countries on the African continent, at a special session of the African Union, undertook to institutionalise efficiency monitoring within their respective national health information management systems. The specific objectives of this study were: (i) to assess the technical efficiency of National Health Systems (NHSs) of African countries for measuring male and female life expectancies, and (ii) to assess changes in health productivity over time with a view to analysing changes in efficiency and changes in technology. The analysis was based on a five-year panel data (1999-2003) from all the 53 countries of continental Africa. Data Envelopment Analysis (DEA) - a non-parametric linear programming approach - was employed to assess the technical efficiency. Malmquist Total Factor Productivity (MTFP) was used to analyse efficiency and productivity change over time among the 53 countries' national health systems. The data consisted of two outputs (male and female life expectancies) and two inputs (per capital total health expenditure and adult literacy). The DEA revealed that 49 (92.5%) countries' NHSs were run inefficiently in 1999 and 2000; 50 (94.3%), 48 (90.6%) and 47 (88.7%) operated inefficiently in 2001, 2002, and 2003 respectively. All the 53 countries' national health systems registered improvements in total factor productivity attributable mainly to technical progress. Fifty-two countries did not experience any change in scale efficiency, while thirty (56.6%) countries' national health systems had a Pure Efficiency Change (PEFFCH) index of less than one, signifying that those countries' NHSs pure efficiency contributed negatively to productivity change. All the 53 countries' national health systems registered improvements in total factor productivity, attributable mainly to technical progress. Over half of the countries' national health systems had a pure efficiency index of less than one, signifying that those countries' NHSs pure efficiency contributed negatively to productivity change. African countries may need to critically evaluate the utility of institutionalising Malmquist TFP type of analyses to monitor changes in health systems economic efficiency and productivity over time. African national health systems, per capita total health expenditure, technical efficiency, scale efficiency, Malmquist indices of productivity change, DEA

Seasonal growth of the crustose lichen Rhizocarpon geographicum (L.) DC. in South Gwynedd, Wales

Seasonal growth was studied in the slow-growing crustose lichen Rhizocarpon geographicum (L.) DC. in an area of South Gwynedd, Wales. Radial growth rate (RGR) of a sample of 20 thalli was measured in situ at three-month intervals over 51 months on a southeast-facing rock surface. There were five periods of significant growth: July-September of 1993, 1994 and 1995, in January-March of 1996, and in April-June of 1997. In four of these periods, growth coincided with a mean temperature maximum (Tmax) over a three-month period exceeding 15°C and three of the maxima with greater than 450 sunshine hours. Two of the growth maxima coincided with periods of total rainfall exceeding 300 mm and one with greater than 50 rain days in a three-month period. There were no significant linear correlations between RGR and the climatic variables measured. However, there were significant non-linear relationships between RGR and Tmax, the mean temperature minimum (Tmin), the total number of air and ground frosts and the number of rain days in a growth period, the relationship with Tmax being the most significant. Hence, in south Gwynedd, maximum growth of R. geographicum occurs in any season although the period July-September appears to be the most favourable. Relationships between growth and climatic variables were non-linear, temperature having the most significant influence on seasonal growth. ©2006 Balaban.

Growth curves of four crustose lichens

The growth curves of four common species of crustose lichens, viz., Buellia aethalea (Ach.) Th. Fr., Lecidea tumida Massai., Rhizocarpon geographicum (L.) DC., and Rhizocarpon reductum Th. Fr. were studied at a site in south Gwynedd, north Wales, UK. Radial growth rates (RGR, mm 1.5 yr-1) were greatest in thalli of R. reductum and least in R. geographicum. Variation in RGR between thalli was greater in B. aethalea and L. tumida than in the species of Rhizocarpon. The relationship between growth rate and thallus diameter was not asymptotic; RGR increasing in smaller thalli to a maximum and then declining in larger diameter thalli. A polynomial curve was fitted to the data; the growth curves being fitted best by a second-order (quadratic) curve, the best fit to this model being shown by B. aethalea. A significant linear regression with a negative slope was also fitted to the growth of the larger thalli of each species. The data suggest that the growth curves of the four crustose lichens differ significantly from the asymptotic curves of foliose lichen species. A phase of declining RGR in larger thalli appears to be characteristic of crustose lichens and is consistent with data from lichenometric studies.

Pole tip recession in linear tape systems

The tribology of linear tape storage system including Linear Tape Open (LTO) and Travan5 was investigated by combining X-ray Photoelectron Spectroscopy (XPS), Auger Electron Spectroscopy (AES), Optical Microscopy and Atomic Force Microscopy (AFM) technologies. The purpose of this study was to understand the tribology mechanism of linear tape systems then projected recording densities may be achieved in future systems. Water vapour pressure or Normalized Water Content (NWC) rather than the Relative Humidity (RH) values (as are used almost universally in this field) determined the extent of PTR and stain (if produced) in linear heads. Approximately linear dependencies were found for saturated PTR increasing with normalized water content increasing over the range studied using the same tape. Fe Stain (if produced) preferentially formed on the head surfaces at the lower water contents. The stain formation mechanism had been identified. Adhesive bond formation is a chemical process that is governed by temperature. Thus the higher the contact pressure, the higher the contact temperature in the interface of head and tape, was produced higher the probability of adhesive bond formation and the greater the amount of transferred material (stain). Water molecules at the interface saturate the surface bonds and makes adhesive junctions less likely. Tape polymeric binder formulation also has a significant role in stain formation, with the latest generation binders producing less transfer of material. This is almost certainly due to higher cohesive bonds within the body of the magnetic layer. TiC in the two-phase ceramic tape-bearing surface (AlTiC) was found to oxidise to form TiO2.The oxidation rate of TiC increased with water content increasing. The oxide was less dense than the underlying carbide; hence the interface between TiO2 oxide and TiC was stressed. Removals of the oxide phase results in the formation of three-body abrasive particles that were swept across the tape head, and gave rise to three-body abrasive wear, particularly in the pole regions. Hence, PTR and subsequent which signal loss and error growth. The lower contact pressure of the LTO system comparing with the Travan5 system ensures that fewer and smaller three-body abrasive particles were swept across the poles and insulator regions. Hence, lower contact pressure, as well as reducing stain in the same time significantly reduces PTR in the LTO system.

Seasonal growth and growth rate-colony size relationships in six species of saxicolous lichens

The pattern of seasonal growth and the relation of growth rate to colony size were studied in four foliose and two crustose species of saxicolous lichens. A new method of measuring growth was used whereby the advance of a sample of lobes along millimetres marked on the substrate was measured under a magnification of x10. Three peaks of growth were found(in March, June and November) for the foliose species and a single peak (in May to August) for the crustose species. THe peaks of growth corresponded approximately to peaks of rainfall. Growth rate in relation to increasing colony size fell in a smooth exponential curve when expressed on a cm squared/ cm squared/ unit time basis. The result is consistent with a linear radial rate for most of the thallus sizes for the six species. There is also evidence for an exponential incresae in growth rate initially until about 1.5 cm thallus diameter in two of the sepcies when the linear radial rate is achieved.

A comparison of the growth curves of the foliose lichen Parmelia conspersa determined by a cross-sectional study and by direct measurement

Changes in the radial growth rate (RGR mm/yr) through life were studied in thalli of the foliose lichen Parmelia conspersa by two methods: (1) a cross-sectional study (Study A) in which the RGR was measured in 60 thalli from 0.2 to 13 cm in diameter, and (2) by radial growth measurements over 4.5 years of fragments, consisting of a single major lobe, which were removed from large thalli and glued to pieces of slate (Study B). Both studies suggested there was a phase of increasing RGR in small thalli followed by a more constant phase, the latter beginning at approximately a thallus radius of 6-8 mm. However, in Study B significantly increased RGR was observed during the second 6-month growth period. This phase of growth was more likely to be due to an increase in lobe width than to an effect of climate. In addition, a lobe in a large thallus with both adjacent lobes removed significantly increased in width over 1 year compared with control lobes. These results suggest that (1) mean lobe width in a thallus may be determined by the intensity of marginal competition between adjacent lobes, and (2) changes in lobe width during the life of a lichen thallus may be a factor determining the establishment of the linear phase of growth in foliose lichens. © 1992.

Studies on the growth rates of lichens

Progress in the field of lichen growth rates is briefly reviewed. The application of a new method of measuring growth rate to thalli of different size has led to the conclusion that there are changes in the radial growth rate during the life of a lichen thallus. For most of the life of a lichen thallus the radial growth rate is constant and the thallus radius increases linearly. Preceeding the linear phase the radial growth rate increases with time and the thallus radius increases logarithmically. There is no evidence for a postlinear phase in the radial growth of a lichen thallus. Studies on the growth rate of lichens are applied both to the problems of determining the age of a lichen thallus on an undated substratum and to an ecological investigation in the field.

Growth phases in the life of a lichen thallus

The growth rates of thalli of foliose saxicolous lichens before and after the linear phase of growth were measured in 1973. Changes in the radial growth rate (measured as mm/year) with thallus size in the prelinear phase (thalli less than approximately 1.5 cm in diameter) were consistent with the hypothesis that early growth of these lichens is loagarithmic. When growth in the prelinear phase was measured as a relative growth rate (measured as sq cm/sq cm/year) there was a rapid rise in growth rate until about 3 mm thallus diameter and then a decline in growth rate. The radial growth rate of non-fragmenting thalli when compared with fragmenting thalli at different stages of fragmentation suggested that radial growth rate does not significantly decline after fragmentation of the thallus. This result is not consistent with a postlinear phase in the radial growth of a lichen thallus.

Data methods in optometry. Part 10: non-linear regression analysis

1. The techniques associated with regression, whether linear or non-linear, are some of the most useful statistical procedures that can be applied in clinical studies in optometry. 2. In some cases, there may be no scientific model of the relationship between X and Y that can be specified in advance and the objective may be to provide a ‘curve of best fit’ for predictive purposes. In such cases, the fitting of a general polynomial type curve may be the best approach. 3. An investigator may have a specific model in mind that relates Y to X and the data may provide a test of this hypothesis. Some of these curves can be reduced to a linear regression by transformation, e.g., the exponential and negative exponential decay curves. 4. In some circumstances, e.g., the asymptotic curve or logistic growth law, a more complex process of curve fitting involving non-linear estimation will be required.

Studies on the growth rates of lichens

Progress in the field of lichen growth rate studies is briefly reviewed. The application of a new method of measuring growth rate to thalli of different size has led to the conclusion that there are changes in the radial growth rate during the life of a lichen thallus. For most of the life of a lichen thallus the radial growth rate is constant and the thallus radius increases linearly. Preceding the linear phase the radial growth rate increases with time and the thallus radius increases logarithmically. There is no evidence for a postlinear phase in the radial growth of a lichen thallus. Studies on the growth rate of lichens are applied both to the problems of determining the age of a lichen thallus on an undated susbtratum and to an ecological investigation in the field.

Factors affecting the growth of Cladophora in relation to river pollution

Nuisance growths of Cladophora have been associated with eutrophication. A review of the literature, however, reveals a scarcity of relevant experimental growth studies. Sampling experimental streams reveals that the addition of sewage effluent to good quality water alters the flora from that dominated by Potamogetan crispus to one dominated by CLadophora. Spatial and temporal differences in biomass of taxa present are discussed in the context of accompanying physicochemical data. In laboratory batch culture, growth of unialgal C. glomerata was accompanied by elevation of medium pH - considered largely responsible for the poor growth in such culture. However, appropriate experimental conditions and indices of growth were selected and the effects of various herbicides assessed. Diquat and terbutryne were shown to possess algicidal activity towards Cladophora. A closed continuous culture apparatus was developed: growth proceeded through lag, logarithmic and linear phases. Inoculum size and medium flow rate had significant effects on growth, and were standardized. In continuous culture, specific growth rate increased linearly with increased duration of light per day, up to 24 hours, and increased light intensity, up to 6000 lux - the highest intensity tested. Comparison of field and laboratory results suggests that ammonia toxicity is attributable to the undissociated form. In the laboratory, 185 µg/1 undissociated ammoniacal nitrogen reduced specific growth rate to 50% of that at 10 µg/1 undissociated ammcniacal nitrogen. 0.077-1.057 mg/1 NO2-N had no significant effect on growth. 7.2-15.2 mg/1 NO3-N had no significant effect on specific growth rate. Neither was any nitrate/phosphate interaction significant. At 4.9 mg/1 PO4-1, specific growth rate was only 48% of that at 1.9 g/1 P04-P. The critical medium PO4-P concentration was <0.1 mg/i. Specific growth rate was reduced to 50% of that in natural water by 0.036 mgCu/l, 0.070 mgzn/1 and 1.03 mgPb/l. Metal uptake was evaluated.

The effects of substrate water availability on the isolation and growth of fungi

The work reported in this thesis was carried out to contribute to the knowledge of the effects of substrate water availability or water activity (a ) on fungal growth parameters and its implications in the preparationw of materials susceptible to biodeterioration. Fungi were isolated from soils of different ecological sites at a range of substrate aw levels controlled by sodium chloride (NaCl). Three groups of fungi were isolated : firstly, those isolated only at high a (aw about 0.997).secondly, those isolated at high and decreasing aw (aw 0.997 to 0.85) and finally, those isolated at only decreased aw (aw O.95 to 0.80). From these isolations, test fungi were selected to study the effects of pH, temperature, exo-enzyme production and biocide efficacy at decreased aw levels, with glycerol and NaCl as a controlling solutes. The linear extension rates of the fungi increased at all test pH values near optimum a of growth. Test fungi of the Aspergillus glaucus group were found to be most resistant to low aw. Growth and survival of vegetative and fruiting bodies at elevated temperatures were enhanced with the addition of a controlling solutes. A. flavus, A. fumigatus displayed high heat resistance and A. amstelodami, A. versicolor and Penicillium citrinum displayed low heat resistance at high aw levels and vice versa at low aw levels. Amylase, lipase and protease activities were studied at lowered aw , using modifications of the test tube method of Raute11a and Cowling. Amylase and protease production in most xerophilic fungi ceased around 0.80 aw , but lipase production in some xerophilic fungi, including A. glatlcus fungi, was up to and including 0.70 aw with g1ycero1.