Impact of just-in-time on job content, employee attitudes and well-being:a longitudinal study

Just-in-time (JIT) production systems are increasingly being seen as a vital way for manufacturing organizations to enhance their competitiveness. A number of commentators have suggested that this will simplify jobs and reduce employee well-being. This paper presents a conceptual framework for interpreting the effects of JIT and reports findings from a study of the impact of JIT on the content of workers'jobs and on job satisfaction and psychological strain. The introduction of JIT led to a reduction in control over work timing, an increase in production pressure, and a drop in job satisfaction. Contrary to claims in the literature, no changes were found in control over work methods, other aspects of cognitive demands and skill use, and in psychological strain. The study shows that JIT can be implemented without radical changes in job content or adverse impact in terms of employee strain, and the implications of these findings are discussed.

Product variety and just-in-time conflict and challenge

This paper addresses the question of how just-in-time can be implemented within high variety manufacture. To illustrate some of the principles in relation to the high variety-low volume situation the case of a computer manufacturer is considered in detail. For contrast the paper also considers the case of the manufacture of highly-configured four wheel drive vehicles where both variety and volumes are high. The most important issue in high variety/low volume production is that JIT operation should be seen in terms of the tactical holding of inventory in upstream buffers within the supply chain so that value is not added to work in progress prematurely. Tactical buffers ensure that service levels are maintained and the risk of stock-outs is minimized. In high variety/high volume production schedule integrity is the key factor, unreliable schedules being a major inhibitor to the introduction of JIT.

Canonical solution groups of a homomorphism : manipulator kinematics, nonparametric regression and distributed object systems

The kinematic mapping of a rigid open-link manipulator is a homomorphism between Lie groups. The homomorphisrn has solution groups that act on an inverse kinematic solution element. A canonical representation of solution group operators that act on a solution element of three and seven degree-of-freedom (do!) dextrous manipulators is determined by geometric analysis. Seven canonical solution groups are determined for the seven do! Robotics Research K-1207 and Hollerbach arms. The solution element of a dextrous manipulator is a collection of trivial fibre bundles with solution fibres homotopic to the Torus. If fibre solutions are parameterised by a scalar, a direct inverse funct.ion that maps the scalar and Cartesian base space coordinates to solution element fibre coordinates may be defined. A direct inverse pararneterisation of a solution element may be approximated by a local linear map generated by an inverse augmented Jacobian correction of a linear interpolation. The action of canonical solution group operators on a local linear approximation of the solution element of inverse kinematics of dextrous manipulators generates cyclical solutions. The solution representation is proposed as a model of inverse kinematic transformations in primate nervous systems. Simultaneous calibration of a composition of stereo-camera and manipulator kinematic models is under-determined by equi-output parameter groups in the composition of stereo-camera and Denavit Hartenberg (DH) rnodels. An error measure for simultaneous calibration of a composition of models is derived and parameter subsets with no equi-output groups are determined by numerical experiments to simultaneously calibrate the composition of homogeneous or pan-tilt stereo-camera with DH models. For acceleration of exact Newton second-order re-calibration of DH parameters after a sequential calibration of stereo-camera and DH parameters, an optimal numerical evaluation of DH matrix first order and second order error derivatives with respect to a re-calibration error function is derived, implemented and tested. A distributed object environment for point and click image-based tele-command of manipulators and stereo-cameras is specified and implemented that supports rapid prototyping of numerical experiments in distributed system control. The environment is validated by a hierarchical k-fold cross validated calibration to Cartesian space of a radial basis function regression correction of an affine stereo model. Basic design and performance requirements are defined for scalable virtual micro-kernels that broker inter-Java-virtual-machine remote method invocations between components of secure manageable fault-tolerant open distributed agile Total Quality Managed ISO 9000+ conformant Just in Time manufacturing systems.

Using a simulation model for capacity management

A simulation model has been constructed of a valve manufacturing plant with the aim of assessing capacity requirements in response to a forecast increase in demand. The plant provides a weekly cycle of valves of varying types, based on a yearly production plan. Production control is provided by a just-in-time type system to minimise inventory. The simulation model investigates the effect on production lead time of a range of valve sequences into the plant. The study required the collection of information from a variety of sources, and a model that reflected the true capabilities of the production system. The simulation results convinced management that substantial changes were needed in order to meet demand. The case highlights the use of simulation in enabling a manager to quantify operational scenarios and thus provide a rational basis on which to take decisions on meeting performance criteria.

Introduction: improving manufacturing performance through technology diffusion, implementation and management

The role of technology management in achieving improved manufacturing performance has been receiving increased attention as enterprises are becoming more exposed to competition from around the world. In the modern market for manufactured goods the demand is now for more product variety, better quality, shorter delivery and greater flexibility, while the financial and environmental cost of resources has become an urgent concern to manufacturing managers. This issue of the International Journal of Technology Management addresses the question of how the diffusion, implementation and management of technology can improve the performance of manufacturing industries. The authors come from a large number of different countries and their contributions cover a wide range of topics within this general theme. Some papers are conceptual, others report on research carried out in a range of different industries including steel production, iron founding, electronics, robotics, machinery, precision engineering, metal working and motor manufacture. In some cases they describe situations in specific countries. Several are based on presentations made at the UK Operations Management Association's Sixth International Conference held at Aston University at which the conference theme was 'Achieving Competitive Edge: Getting Ahead Through Technology and People'. The first two papers deal with questions of advanced manufacturing technology implementation and management. Firstly Beatty describes a three year longitudinal field study carried out in ten Canadian manufacturing companies using CADICAM and CIM systems. Her findings relate to speed of implementation, choice of system type, the role of individuals in implementation, organization and job design. This is followed by a paper by Bessant in which he argues that a more a strategic approach should be taken towards the management of technology in the 1990s and beyond. Also considered in this paper are the capabilities necessary in order to deploy advanced manufacturing technology as a strategic resource and the way such capabilities might be developed within the firm. These two papers, which deal largely with the implementation of hardware, are supplemented by Samson and Sohal's contribution in which they argue that a much wider perspective should be adopted based on a new approach to manufacturing strategy formulation. Technology transfer is the topic of the following two papers. Pohlen again takes the case of advanced manufacturing technology and reports on his research which considers the factors contributing to successful realisation of AMT transfer. The paper by Lee then provides a more detailed account of technology transfer in the foundry industry. Using a case study based on a firm which has implemented a number of transferred innovations a model is illustrated in which the 'performance gap' can be identified and closed. The diffusion of technology is addressed in the next two papers. In the first of these, by Lowe and Sim, the managerial technologies of 'Just in Time' and 'Manufacturing Resource Planning' (or MRP 11) are examined. A study is described from which a number of factors are found to influence the adoption process including, rate of diffusion and size. Dahlin then considers the case of a specific item of hardware technology, the industrial robot. Her paper reviews the history of robot diffusion since the early 1960s and then tries to predict how the industry will develop in the future. The following two papers deal with the future of manufacturing in a more general sense. The future implementation of advanced manufacturing technology is the subject explored by de Haan and Peters who describe the results of their Dutch Delphi forecasting study conducted among a panel of experts including scientists, consultants, users and suppliers of AMT. Busby and Fan then consider a type of organisational model, 'the extended manufacturing enterprise', which would represent a distinct alternative pure market-led and command structures by exploiting the shared knowledge of suppliers and customers. The three country-based papers consider some strategic issues relating manufacturing technology. In a paper based on investigations conducted in China He, Liff and Steward report their findings from strategy analyses carried out in the steel and watch industries with a view to assessing technology needs and organizational change requirements. This is followed by Tang and Nam's paper which examines the case of machinery industry in Korea and its emerging importance as a key sector in the Korean economy. In his paper which focuses on Venezuela, Ernst then considers the particular problem of how this country can address the problem of falling oil revenues. He sees manufacturing as being an important contributor to Venezuela's future economy and proposes a means whereby government and private enterprise can co-operate in development of the manufacturing sector. The last six papers all deal with specific topics relating to the management manufacturing. Firstly Youssef looks at the question of manufacturing flexibility, introducing and testing a conceptual model that relates computer based technologies flexibility. Dangerfield's paper which follows is based on research conducted in the steel industry. He considers the question of scale and proposes a modelling approach determining the plant configuration necessary to meet market demand. Engstrom presents the results of a detailed investigation into the need for reorganising material flow where group assembly of products has been adopted. Sherwood, Guerrier and Dale then report the findings of a study into the effectiveness of Quality Circle implementation. Stillwagon and Burns, consider how manufacturing competitiveness can be improved individual firms by describing how the application of 'human performance engineering' can be used to motivate individual performance as well as to integrate organizational goals. Finally Sohal, Lewis and Samson describe, using a case study example, how just-in-time control can be applied within the context of computer numerically controlled flexible machining lines. The papers in this issue of the International Journal of Technology Management cover a wide range of topics relating to the general question of improving manufacturing performance through the dissemination, implementation and management of technology. Although they differ markedly in content and approach, they have the collective aim addressing the concepts, principles and practices which provide a better understanding the technology of manufacturing and assist in achieving and maintaining a competitive edge.

Setting parameters in MRP for the effective management of bought-out inventory in a JIT assembly environment

In recent years, UK industry has seen an explosive growth in the number of `Computer Aided Production Management' (CAPM) system installations. Of the many CAPM systems, materials requirement planning/manufacturing resource planning (MRP/MRPII) is the most widely implemented. Despite the huge investments in MRP systems, over 80 percent are said to have failed within 3 to 5 years of installation. Many people now assume that Just-In-Time (JIT) is the best manufacturing technique. However, those who have implemented JIT have found that it also has many problems. The author argues that the success of a manufacturing company will not be due to a system which complies with a single technique; but due to the integration of many techniques and the ability to make them complement each other in a specific manufacturing environment. This dissertation examines the potential for integrating MRP with JIT and Two-Bin systems to reduce operational costs involved in managing bought-out inventory. Within this framework it shows that controlling MRP is essential to facilitate the integrating process. The behaviour of MRP systems is dependent on the complex interactions between the numerous control parameters used. Methodologies/models are developed to set these parameters. The models are based on the Pareto principle. The idea is to use business targets to set a coherent set of parameters, which not only enables those business targets to be realised, but also facilitates JIT implementation. It illustrates this approach in the context of an actual manufacturing plant - IBM Havant. (IBM Havant is a high volume electronics assembly plant with the majority of the materials bought-out). The parameter setting models are applicable to control bought-out items in a wide range of industries and are not dependent on specific MRP software. The models have produced successful results in several companies and are now being developed as commercial products.

The application of computerised modelling techniques in manufacturing system design

The absence of a definitive approach to the design of manufacturing systems signifies the importance of a control mechanism to ensure the timely application of relevant design techniques. To provide effective control, design development needs to be continually assessed in relation to the required system performance, which can only be achieved analytically through computer simulation. The technique providing the only method of accurately replicating the highly complex and dynamic interrelationships inherent within manufacturing facilities and realistically predicting system behaviour. Owing to the unique capabilities of computer simulation, its application should support and encourage a thorough investigation of all alternative designs. Allowing attention to focus specifically on critical design areas and enabling continuous assessment of system evolution. To achieve this system analysis needs to efficient, in terms of data requirements and both speed and accuracy of evaluation. To provide an effective control mechanism a hierarchical or multi-level modelling procedure has therefore been developed, specifying the appropriate degree of evaluation support necessary at each phase of design. An underlying assumption of the proposal being that evaluation is quick, easy and allows models to expand in line with design developments. However, current approaches to computer simulation are totally inappropriate to support the hierarchical evaluation. Implementation of computer simulation through traditional approaches is typically characterized by a requirement for very specialist expertise, a lengthy model development phase, and a correspondingly high expenditure. Resulting in very little and rather inappropriate use of the technique. Simulation, when used, is generally only applied to check or verify a final design proposal. Rarely is the full potential of computer simulation utilized to aid, support or complement the manufacturing system design procedure. To implement the proposed modelling procedure therefore the concept of a generic simulator was adopted, as such systems require no specialist expertise, instead facilitating quick and easy model creation, execution and modification, through simple data inputs. Previously generic simulators have tended to be too restricted, lacking the necessary flexibility to be generally applicable to manufacturing systems. Development of the ATOMS manufacturing simulator, however, has proven that such systems can be relevant to a wide range of applications, besides verifying the benefits of multi-level modelling.

Human performance modelling as an aid in the process of manufacturing system design

Manufacturing system design is an ongoing activity within industry. Modelling tools based on Discrete Event Simulation are often used by practitioners during this design cycle. However, such tools do not adequately model the behaviour of 'direct' workers in manufacturing environments. There is an important need to expand the capability of modelling to include the relationships between human centred factors (demography, attitudes, beliefs, etc), their working environment (physical and organizational), and their subsequent performance in terms of productive routines. Therefore, this paper describes research that has formed a pilot modelling methodology that is an important first step in providing such a capability.

An opportunity for system dynamics in manufacturing system modelling

The computer simulation of manufacturing systems is commonly carried out using discrete event simulation (DES). Indeed, there appears to be a lack of applications of continuous simulation methods, particularly system dynamics (SD), despite evidence that this technique is suitable for industrial modelling. This paper investigates whether this is due to a decline in the general popularity of SD, or whether modelling of manufacturing systems represents a missed opportunity for SD. On this basis, the paper first gives a review of the concept of SD and fully describes the modelling technique. Following on, a survey of the published applications of SD in the 1990s is made by developing and using a structured classification approach. From this review, observations are made about the application of the SD method and opportunities for future research are suggested.

Introduction : the role of quality, production and technological innovation in improving competitive performance

Quality, production and technological innovation management rank among the most important matters of concern to modern manufacturing organisations. They can provide companies with the decisive means of gaining a competitive advantage, especially within industries where there is an increasing similarity in product design and manufacturing processes. The papers in this special issue of International Journal of Technology Management have all been selected as examples of how aspects of quality, production and technological innovation can help to improve competitive performance. Most are based on presentations made at the UK Operations Management Association's Sixth International Conference held at Aston University at which the theme was 'Getting Ahead Through Technology and People'. At the conference itself over 80 papers were presented by authors from 15 countries around the world. Among the many topics addressed within the conference theme, technological innovation, quality and production management emerged as attracting the greatest concern and interest of delegates, particularly those from industry. For any new initiative to be implemented successfully, it should be led from the top of the organization. Achieving the desired level of commitment from top management can, however, be a difficulty. In the first paper of this issue, Mackness investigates this question by explaining how systems thinking can help. In the systems approach, properties such as 'emergence', 'hierarchy', 'commnication' and 'control' are used to assist top managers in preparing for change. Mackness's paper is then complemented by Iijima and Hasegawa's contribution in which they investigate the development of Quality Information Management (QIM) in Japan. They present the idea of a Design Review and demonstrate how it can be used to trace and reduce quality-related losses. The next paper on the subject of quality is by Whittle and colleagues. It relates to total quality and the process of culture change within organisations. Using the findings of investigations carried out in a number of case study companies, they describe four generic models which have been identified as characterising methods of implementing total quality within existing organisation cultures. Boaden and Dale's paper also relates to the management of quality, but looks specifically at the construction industry where it has been found there is still some confusion over the role of Quality Assurance (QA) and Total Quality Management (TQM). They describe the results of a questionnaire survey of forty companies in the industry and compare them to similar work carried out in other industries. Szakonyi's contribution then completes this group of papers which all relate specifically to the question of quality. His concern is with the two ways in which R&D or engineering managers can work on improving quality. The first is by improving it in the laboratory, while the second is by working with other functions to improve quality in the company. The next group of papers in this issue all address aspects of production management. Umeda's paper proposes a new manufacturing-oriented simulation package for production management which provides important information for both design and operation of manufacturing systems. A simulation for production strategy in a Computer Integrated Manufacturing (CIM) environment is also discussed. This paper is then followed by a contribution by Tanaka and colleagues in which they consider loading schedules for manufacturing orders in a Material Requirements Planning (MRP) environment. They compare mathematical programming with a knowledge-based approach, and comment on their relative effectiveness for different practical situations. Engstrom and Medbo's paper then looks at a particular aspect of production system design, namely the question of devising group working arrangements for assembly with new product structures. Using the case of a Swedish vehicle assembly plant where long cycle assembly work has been adopted, they advocate the use of a generally applicable product structure which can be adapted to suit individual local conditions. In the last paper of this particular group, Tay considers how automation has affected the production efficiency in Singapore. Using data from ten major industries he identifies several factors which are positively correlated with efficiency, with capital intensity being of greatest interest to policy makers. The two following papers examine the case of electronic data interchange (EDI) as a means of improving the efficiency and quality of trading relationships. Banerjee and Banerjee consider a particular approach to material provisioning for production systems using orderless inventory replenishment. Using the example of a single supplier and multiple buyers they develop an analytical model which is applicable for the exchange of information between trading partners using EDI. They conclude that EDI-based inventory control can be attractive from economic as well as other standpoints and that the approach is consistent with and can be instrumental in moving towards just-in-time (JIT) inventory management. Slacker's complementary viewpoint on EDI is from the perspective of the quality relation-ship between the customer and supplier. Based on the experience of Lucas, a supplier within the automotive industry, he concludes that both banks and trading companies must take responsibility for the development of payment mechanisms which satisfy the requirements of quality trading. The three final papers of this issue relate to technological innovation and are all country based. Berman and Khalil report on a survey of US technological effectiveness in the global economy. The importance of education is supported in their conclusions, although it remains unclear to what extent the US government can play a wider role in promoting technological innovation and new industries. The role of technology in national development is taken up by Martinsons and Valdemars who examine the case of the former Soviet Union. The failure to successfully infuse technology into Soviet enterprises is seen as a factor in that country's demise, and it is anticipated that the newly liberalised economies will be able to encourage greater technological creativity. This point is then taken up in Perminov's concluding paper which looks in detail at Russia. Here a similar analysis is made of the concluding paper which looks in detail at Russia. Here a similar analysis is made of the Soviet Union's technological decline, but a development strategy is also presented within the context of the change from a centralised to a free market economy. The papers included in this special issue of the International Journal of Technology Management each represent a unique and particular contribution to their own specific area of concern. Together, however, they also argue or demonstrate the general improvements in competitive performance that can be achieved through the application of modern principles and practice to the management of quality, production and technological innovation.

Modular system design and control for flexible assembly

Flexible Assembly Systems (FASs) are normally associated with the automatic, or robotic, assembly of products, supported by automated material handling systems. However, manual assembly operations are still prevalent within many industries, where the complexity and variety of products prohibit the development of suitable automated assembly equipment. This article presents a generic model for incorporating flexibility into the design and control of assembly operations concerned with high variety/low volume manufacture, drawing on the principles for Flexible Manufacturing Systems (FMS) and Just-in-Time (JIT) delivery. It is based on work being undertaken in an electronics company where the assembly operations have been overhauled and restructured in response to a need for greater flexibility, shorter cycle times and reduced inventory levels. The principles employed are in themselves not original. However, the way they have been combined and tailored has created a total manufacturing control system which represents a new concept for responding to demands placed on market driven firms operating in an uncertain environment.

Some aspects of scheduling in a group technology manufacturing system

DUE TO COPYRIGHT RESTRICTIONS ONLY AVAILABLE FOR CONSULTATION AT ASTON UNIVERSITY LIBRARY AND INFORMATION SERVICES WITH PRIOR ARRANGEMENT

Research on rework strategies for reconfigurable manufacturing system considering mission reliability

Rework strategies that involve different checking points as well as rework times can be applied into reconfigurable manufacturing system (RMS) with certain constraints, and effective rework strategy can significantly improve the mission reliability of manufacturing process. The mission reliability of process is a measurement of production ability of RMS, which serves as an integrated performance indicator of the production process under specified technical constraints, including time, cost and quality. To quantitatively characterize the mission reliability and basic reliability of RMS under different rework strategies, rework model of RMS was established based on the method of Logistic regression. Firstly, the functional relationship between capability and work load of manufacturing process was studied through statistically analyzing a large number of historical data obtained in actual machining processes. Secondly, the output, mission reliability and unit cost in different rework paths were calculated and taken as the decision variables based on different input quantities and the rework model mentioned above. Thirdly, optimal rework strategies for different input quantities were determined by calculating the weighted decision values and analyzing advantages and disadvantages of each rework strategy. At last, case application were demonstrated to prove the efficiency of the proposed method.