Mechanics of longitudinal rolling of tube through three-grooved rolls

This investigation examined the process of the longitudinal rolling of tubes through a set of three driven grooved rolls. Tubes were rolled with or without internal support i.e. under mandrel rolling or sinking conditions. Knowledge was required of the way in which the roll separating force and rolling torque vary for different conditions of rolling. The objective of this work being to obtain a better understanding and optimization of the mechanics of the process. The design and instrumentation of a complete experimental three-roll mill for the rolling of lead tube as an analogue material for hot steel, with the measurement of the individual roll force and torque is described. A novel type of roll load cell was incorporated and its design and testing discussed. Employing three roll sizes of 170 mm, 255 mm and 340 mm shroud diameter, precise tube specimens of various tube diameter to thickness ratios were rolled under sinking and mandrel rolling conditions. To obtain an indication of the tube-roll contact areas some of the specimens were partially rolled. For comparative purposes the remaining tubes were completely rolled as a single pass. The roll forces, torques and tube parameters e.g. reduction of area, D/t ratio, were collated and compared for each of the three roll diameters considered. The influence of friction, particularly in the mandrel rolling process, was commented upon. Theoretical studies utilising the equilibrium and energy methods were applied to both the sinking and mandrel rolling processes. In general, the energy approach gave better comparison with experiment, especially for mandrel rolling. The influence of the tube deformation zones on the two processes was observed and on the subsequent modification of the tube-roll arc contact length. A rudimentary attempt was made in the theoretical sinking analysis to allow for the deformation zone prior to roll contact; some success was noted. A general survey of the available tube rolling literature, for both the sinking and mandrel processes has been carried out.

Business strategy and the environment in a traditional manufacturing sector

This research is concerned with the relationship between business strategy and the environment within traditional sectors. It has sought to learn more about the strategic environmental attitudes of SMEs compared with large companies operating under the same market conditions. The sector studied is the ceramics industry (including tableware & ornamental-ware, sanitary ware & tiles, bricks, industrial & advanced ceramics and refractories) in the UK and France. Unlike the automotive, oil, chemical, steel or metal processing sectors, this industry is one of the few industrial sectors which has rarely been considered. The information on this sector was gathered by interviewing people responsible for environmental issues. The actual programme of valid interviews represents approximately a quarter of the UK and French ceramics industry which is large enough to enable a quantitative analysis and significant and non-biased conclusions. As a whole, all companies surveyed agreed that the ceramics activity impacts on the environment, and that they are increasingly affected both by environmental legislation, and by various non-legislative pressures. Approaches to the environmental agenda differ significantly among large and small companies. Smaller companies feel particularly pressed both by the financial costs and management time required to meet complex and changing legislation. The results of this survey also suggest that the ceramics industry sees environmental issues in terms of increased costs rather than new business opportunities. This is due principally to fears of import substitution from countries with lower environmental standards. Finally, replies indicate that generally there is a low level of awareness of the current legislative framework, suggesting a need to shift from a regulatory approach to a more self-regulated approach which encourages companies to be more proactive

Novel biodegradable fibres for applications in tissue engineering and drug delivery

The preparation and characterisation of novel biodegradable polymer fibres for application in tissue engineering and drug delivery are reported. Poly(e-caprolactone) (PCL) fibres were produced by wet spinning from solutions in acetone under low shear (gravity flow) conditions. The tensile strength and stiffness of as-spun fibres were highly dependent on the concentration of the spinning solution. Use of a 6% w/v solution resulted in fibres having strength and stiffness of 1.8 MPa and 0.01 GPa respectively, whereas these values increased to 9.9 MPa and 0.1 GPa when fibres were produced from 20% w/v solutions. Cold drawing to an extension of 500% resulted in further increases in fibre strength (up to 50 MPa) and stiffness (0.3 GPa). Hot drawing to 500% further increased the fibre strength (up to 81 MPa) and stiffness (0.5 GPa). The surface morphology of as-spun fibres was modified, to yield a directional grooved pattern by drying in contact with a mandrel having a machined topography characterised by a peak-peak separation of 91 mm and a peak height of 30 mm. Differential scanning calorimetery (DSC) analysis of as-spun fibres revealed the characteristic melting point of PCL at around 58°C and a % crystallinity of approximately 60%. The biocompatibility of as-spun fibres was assessed using cell culture. The number of attached 3T3 Swiss mouse fibroblasts, C2C12 mouse myoblasts and human umbilical vein endothelial cells (HUVECs) on as-spun, 500% cold drawn, and gelatin coated PCL fibres were observed. The results showed that the fibres promoted cell proliferation for 9 days in cell culture and was slightly lower than on tissue culture plastic. The morphology of all cell lines was assessed on the various PCL fibres using scanning electron microscopy. The cell function of HUVECs growing on the as-spun PCL fibres was evaluated. The ability HUVECs to induce an immune response when stimulated with lipopolysaccaride (LPS) and thereby to increase the amount of cell surface receptors was assessed by flow cytometry and reverse transcription-polymerase chain reaction (RT-PCR). The results showed that PCL fibres did not inhibit this function compared to TCP. As-spun PCL fibres were loaded with 1 % ovine albumin (OVA) powder, 1% OVA nanoparticles and 5% OVA nanoparticles by weight and the protein release was assessed in vitro. PCL fibres loaded with 1 % OVA powder released 70%, 1% OVA nanoparticle released 60% and the 5% OVA nanoparticle released 25% of their protein content over 28 days. These release figures did not alter when the fibres were subjected to lipase enzymatic degradation. The OVA released was examined for structural integrity by SDS-PAGE. This showed that the protein molecular weight was not altered after incorporation into the fibres. The bioactivity of progesterone was assessed following incorporation into PCL fibres. Results showed that the progesterone released had a pronounced effect on MCF-7 breast epithelial cells, inhibiting their proliferation. The PCL fibres display high fibre compliance, a potential for controlling the fibre surface architecture to promote contact guidance effects, favorable proliferation rate of fibroblasts, myoblasts and HUVECs and the ability to release pharmaceuticals. These properties recommended their use for 3-D scaffold production in soft tissue engineering and the fibres could also be exploited for controlled presentation and release of biopharmaceuticals such as growth factors.

Drug/Water interactions in hydrogel matrices

The primary aim of this research has been the investigation of the role of water structuring effects in the widely different extents of irritancy displayed by certain antibiotics. The compounds involved were members of the Lincomycin group of antibiotics. The aqueous solution behaviour of these co~pounds was studied using techniques such as vapour pressure osmometry end differential scanning calorimetry (D.S.C.). The effects of the antibiotics on water structure in hydrogel membrane preparations In which the equilibrium water content (E.W.C.) and constituent amounts of freezing and non-freezing water ware varied were also investigated using D.S.C. The permeability of water swollen hydrogel preparations to aqueous antibiotic solutions as well as other solutes were studied. A series of hydrogel preparations into which the antibiotics had been incorporated during polymerisation were developed and used in studies of the effects of the antibiotics end their water structure modifications on the permeation of a range of solutes.

The investigation of vegetation change using remote sensing to detect and monitor migration of landfill gas

Decomposition of domestic wastes in an anaerobic environment results in the production of landfill gas. Public concern about landfill disposal and particularly the production of landfill gas has been heightened over the past decade. This has been due in large to the increased quantities of gas being generated as a result of modern disposal techniques, and also to their increasing effect on modern urban developments. In order to avert diasters, effective means of preventing gas migration are required. This, in turn requires accurate detection and monitoring of gas in the subsurface. Point sampling techniques have many drawbacks, and accurate measurement of gas is difficult. Some of the disadvantages of these techniques could be overcome by assessing the impact of gas on biological systems. This research explores the effects of landfill gas on plants, and hence on the spectral response of vegetation canopies. Examination of the landfill gas/vegetation relationship is covered, both by review of the literature and statistical analysis of field data. The work showed that, although vegetation health was related to landfill gas, it was not possible to define a simple correlation. In the landfill environment, contribution from other variables, such as soil characteristics, frequently confused the relationship. Two sites are investigated in detail, the sites contrasting in terms of the data available, site conditions, and the degree of damage to vegetation. Gas migration at the Panshanger site was dominantly upwards, affecting crops being grown on the landfill cap. The injury was expressed as an overall decline in plant health. Discriminant analysis was used to account for the variations in plant health, and hence the differences in spectral response of the crop canopy, using a combination of soil and gas variables. Damage to both woodland and crops at the Ware site was severe, and could be easily related to the presence of gas. Air photographs, aerial video, and airborne thematic mapper data were used to identify damage to vegetation, and relate this to soil type. The utility of different sensors for this type of application is assessed, and possible improvements that could lead to more widespread use are identified. The situations in which remote sensing data could be combined with ground survey are identified. In addition, a possible methodology for integrating the two approaches is suggested.

Ductile fracture mechanisms in a structural steel

Microstructural fracture processes in a BS4360 Grade 50D structural steel with lower sulphur content were studied in smooth tensile specimen tests and Charpy-size bend bar tests. Based on the experimental analysis, an experimental void growth relation with the plastic strain and stress triaxiality and multiplying factor on void growth were determined. Experimental results show that the void growth relation can be reasonably used to estimate the constraint in the specimens containing the notch or crack, also they can be used to evaluate the variations of the stress triaxiality in front of the notch and crack tip under general yielding condition. Side-grooves obviously increase the constraint of the CVN specimens. Strain hardening leads to increasing the stress triaxiality, and decelerating the net void growth. This is especially true for the values of stress triaxiality more than about one. Additionally, the effect of the stress triaxiality on the critical void growth corresponding to the onset of ductile tearing was preliminarily investigated. In this work, a large number of smaller specimens were tested to investigate the ductile-brittle transition behaviour of the structural steel. A void growth rate explanation was suggested for evaluating the temperature transition behaviour. The elastic-plastic fracture tough-ness values based on small specimen tests, such as pre-cracked side-grooved bending specimen and short bar tensile specimen, may give large overestimates of the plane strain fracture toughness.

The use of future Internet technologies in the agriculture and food sectors:integrating the supply chain

The Future Internet is expected to greatly influence how the food and agriculture sector is currently operating. In this paper, we present the specific characteristics of the agri-food sector focusing on how information management in this area will take place under a highly heterogeneous group of actors and services, based on the EU SmartAgriFood project. We also discuss how a new dynamic marketplace will be realized based on the adoption of a number of specialized software modules, called “Generic Enablers” that are currently developed in the context of the EU FI-WARE project. Thus, the paper presents the overall vision for data integration along the supply chain as well as the development and federation of Future Internet services that are expected to revolutionize the agriculture sector.

Topographical guidance of intervertebral disc cell growth in vitro:towards the development of tissue repair strategies for the anulus fibrosus

The anulus fibrosus (AF) of the intervertebral disc consists of concentric sheets of collagenous matrix that is synthesised during embryogenesis by aligned disc cells. This highly organised structure may be severely disrupted during disc degeneration and/or herniation. Cell scaffolds that incorporate topographical cues as contact guidance have been used successfully to promote the healing of injured tendons. Therefore, we have investigated the effects of topography on disc cell growth. We show that disc cells from the AF and nucleus pulposus (NP) behaved differently in monolayer culture on micro-grooved membranes of polycaprolactone (PCL). Both cell types aligned to and migrated along the membrane's micro-grooves and ridges, but AF cells were smaller (or less spread), more bipolar and better aligned to the micro-grooves than NP cells. In addition, AF cells were markedly more immunopositive for type I collagen, but less immunopositive for chondroitin-6-sulphated proteoglycans than NP cells. There was no evidence of extracellular matrix (ECM) deposition. Disc cells cultured on non-grooved PCL did not show any preferential alignment at sub-confluence and did not differ in their pattern of immunopositivity to those on grooved PCL. We conclude that substratum topography is effective in aligning disc cell growth and may be useful in tissue engineering for the AF. However, there is a need to optimise cell sources and/or environmental conditions (e.g. mechanical influences) to promote the synthesis of an aligned ECM.

A cloud-based farm management system:architecture and implementation

Recent technological advances have paved the way for developing and offering advanced services for the stakeholders in the agricultural sector. A paradigm shift is underway from proprietary and monolithic tools to Internet-based, cloud hosted, open systems that will enable more effective collaboration between stakeholders. This new paradigm includes the technological support of application developers to create specialized services that will seamlessly interoperate, thus creating a sophisticated and customisable working environment for the end users. We present the implementation of an open architecture that instantiates such an approach, based on a set of domain independent software tools called "generic enablers" that have been developed in the context of the FI-WARE project. The implementation is used to validate a number of innovative concepts for the agricultural sector such as the notion of a services' market place and the system's adaptation to network failures. During the design and implementation phase, the system has been evaluated by end users, offering us valuable feedback. The results of the evaluation process validate the acceptance of such a system and the need of farmers to have access to sophisticated services at affordable prices. A summary of this evaluation process is also presented in this paper. © 2013 Elsevier B.V.

Engineering education research - the UK perspective at a time of change

Engineering education in the United Kingdom is at the point of embarking upon an interesting journey into uncharted waters. At no point in the past have there been so many drivers for change and so many opportunities for the development of engineering pedagogy. This paper will look at how Engineering Education Research (EER) has developed within the UK and what differentiates it from the many small scale practitioner interventions, perhaps without a clear research question or with little evaluation, which are presented at numerous staff development sessions, workshops and conferences. From this position some examples of current projects will be described, outcomes of funding opportunities will be summarised and the benefits of collaboration with other disciplines illustrated. In this study, I will account for how the design of task structure according to variation theory, as well as the probe-ware technology, make the laws of force and motion visible and learnable and, especially, in the lab studied make Newton's third law visible and learnable. I will also, as a comparison, include data from a mechanics lab that use the same probe-ware technology and deal with the same topics in mechanics, but uses a differently designed task structure. I will argue that the lower achievements on the FMCE-test in this latter case can be attributed to these differences in task structure in the lab instructions. According to my analysis, the necessary pattern of variation is not included in the design. I will also present a microanalysis of 15 hours collected from engineering students' activities in a lab about impulse and collisions based on video recordings of student's activities in a lab about impulse and collisions. The important object of learning in this lab is the development of an understanding of Newton's third law. The approach analysing students interaction using video data is inspired by ethnomethodology and conversation analysis, i.e. I will focus on students practical, contingent and embodied inquiry in the setting of the lab. I argue that my result corroborates variation theory and show this theory can be used as a 'tool' for designing labs as well as for analysing labs and lab instructions. Thus my results have implications outside the domain of this study and have implications for understanding critical features for student learning in labs. Engineering higher education is well used to change. As technology develops the abilities expected by employers of graduates expand, yet our understanding of how to make informed decisions about learning and teaching strategies does not without a conscious effort to do so. With the numerous demands of academic life, we often fail to acknowledge our incomplete understanding of how our students learn within our discipline. The journey facing engineering education in the UK is being driven by two classes of driver. Firstly there are those which we have been working to expand our understanding of, such as retention and employability, and secondly the new challenges such as substantial changes to funding systems allied with an increase in student expectations. Only through continued research can priorities be identified, addressed and a coherent and strong voice for informed change be heard within the wider engineering education community. This new position makes it even more important that through EER we acquire the knowledge and understanding needed to make informed decisions regarding approaches to teaching, curriculum design and measures to promote effective student learning. This then raises the question 'how does EER function within a diverse academic community?' Within an existing community of academics interested in taking meaningful steps towards understanding the ongoing challenges of engineering education a Special Interest Group (SIG) has formed in the UK. The formation of this group has itself been part of the rapidly changing environment through its facilitation by the Higher Education Academy's Engineering Subject Centre, an entity which through the Academy's current restructuring will no longer exist as a discrete Centre dedicated to supporting engineering academics. The aims of this group, the activities it is currently undertaking and how it expects to network and collaborate with the global EER community will be reported in this paper. This will include explanation of how the group has identified barriers to the progress of EER and how it is seeking, through a series of activities, to facilitate recognition and growth of EER both within the UK and with our valued international colleagues.