The tribology of laminated magnetic recording heads

This thesis investigates the mechanisms that lead to pole tip recession (PTR) in laminated magnetic recording heads (also known as "sandwich heads"). These heads provide a platform for the utilisation of advanced soft magnetic thin films in practical recording heads suitable for high frequency helical scan tape recording systems. PTR results from a differential wear of the magnetic pole piece from the tape-bearing surface of the head. It results in a spacing loss of the playback or read signal of 54.6dB per recording wavelength separation of the poles from the tape. PTR depends on the material combination used in the head, on the tape type and the climate - temperature and relative humidity (r.h.). Five head materials were studied: two non-magnetic substrate materials- sintered multi granular CaTi03 and composite CaTi03/ZrTi04/Ti02 and three soft magnetic materials- amorphous CoNbZr, and nanocrystalline FeNbSiN and FeTaN. Single material dummy heads were constructed and their wear rates measured when cycling them in a Hi-8 camcorder against commercially available metal particulate (MP) and metal evaporated (ME) tapes in three different climates: 25°C/20%r.h., 25°C/80%r.h. and 40°C/80%r.h. X-ray photoelectron spectroscopy (XPS) was used to examine changes the head surface chemistry. Atomic force microscopy (AFM) was used to examine changes in head and tape surface topography. PTR versus cycling time of laminated heads of CaTi03/ZrTiO4/Ti02 and FeTaN construction was measured using AFM. The principal wear mechanism observed for all head materials was microabrasion caused by the mating body - the tape surface. The variation in wear rate with climate and tape type was due to a variation in severity in this mechanism, except for tape cycling at 40°C in which gross damage was observed to be occurring to the head surface. Two subsidiary wear mechanisms were found: third body scratching (all materials) and grain pullout (both ceramics and FeNbSiN). No chemical wear was observed, though tribochemical reactions were observed on the metal head surfaces. PTR was found to be caused by two mechanisms - the first differential microabrasion of the metal and substrate materials and which was characterised by a low (~10nm) equilibrium value. The second was by deep ploughing by third body debris particles, thought mainly to be grain pullout particles. This level of PTR caused by this mechanism was often more severe, and of a non-equilibrium nature. It was observed more for ME tape, especially at 40°C/80%r.h. and 25°c/20%r.h. Two other phenomena on the laminated head pole piece were observed and commented upon: staining and ripple texturing.

Field experiments on competition between three foliose lichens using the de Wit experimental design

Competition between three foliose, saxicolous lichens common on slate rock in South Gwynedd, Wales, U.K. was studied experimentally using the de Wit design. Fragments of the three species were cut from the edges of large thalli, glued to 5 x 5 cm plots marked out on pieces of slate which were then placed on boards in the field. For each combination of pairs of species, the two species were grown either in monoculture at a density of 24 fragments per plot or together in three mixtures in differing proportions, i.e. species A:B with 16:8, 12:12 and 8:16 fragments per plot; the density remaining constant throughout. Area of the species in the plots after 3 years was used as an estimate of growth. Physcia orbicularis and Parmelia glabratula ssp. fuliginosa grew similarly in monoculture. In mixtures of the two, growth of each species was linearly related to its proportion in a mixture, suggesting little competition had occurred during three years. By contrast, the growth of Parmelia conspersa in monoculture was significantly greater than that of P. orbicularis or P. glabratula. In addition, the growth of both species was substantially reduced in mixtures with P. conspersa; P. glabratula being eliminated in the mixture in which it was the minority species. These results suggest that P. conspersa should predominate in communities with either of the other two species and, in the absence of P. conspersa, communities dominated by P.orbicularis and P. glabratula should be more stable.

Growth of experimentally reconstructed thalli of the lichen Parmelia conspersa

The centres of thalli of Parmelia conspersa (Ehrh. ex Ach.) Ach. were removed, the major lobes were separated from each other and from the substratum, and then the lobes were glued back together in their original configuration. The mean radial growth, the pattern of seasonal growth, and the degree of variation in growth between lobes of the reconstructed thalli, were similar to those of control thalli. When lobes were removed from thalli and glued apart from one another, the pattern of seasonal growth and the degree of variation in lobe growth were unaffected, but annual growth rates were reduced compared with lobes reconstructed into a thallus. Glueing the lobes together in a different configuration and constructing thalli in which each lobe came from a different ‘donor’ thallus did not influence the mean radial growth of the lobes or the degree of variation in lobe growth. These results suggest that although major lobes of P. conspersa are influenced by the proximity of their neighbours there is little chemical exchange between them. In addition, some thalli may form as a result of the fusion of lobes or propagules derived from different individuals. Copyright © 1984, Wiley Blackwell. All rights reserved

Competitive interactions between four foliose lichen species with and without nutrient enrichment

Competition between four foliose lichen species, common on slate rock surfaces in South Gwynedd, Wales, UK, was studied in experimental plots with and without nutrient enrichment by bird droppings. Fragments of the four lichens were glued to pieces of slate on horizontal boards in monoculture and in two-, three- and four-species mixtures in a factorial experimental design. In monoculture, nutrient enrichment increased thallus area of Parmelia conspersa (Ehrh. ex. Ach.) Ach., decreased thallus areas of Parmelia saxatilis (L.) Ach. and Parmelia glabratula ssp. fuliginosa (Fr. ex. Duby) Laundon, and did not affect thallus area of Phaeophyscia orbicularis (Necker) Moberg compared with untreated thalli. In the mixtures, P. conspersa and Ph. orbicularis were equally effective competitors in plots with and without nutrient enrichment. Addition of bird droppings, however, altered the ability of P. saxatilis and P. glabratula ssp. fuliginosa, to compete with the other species, the competitive ability of both species being reduced in some mixtures but increased in others. The results suggest that nutrient enrichment may alter the competitive balance between the four lichen species and this may be a factor determining their relative abundance on rock surfaces in South Gwynedd.

Lobe interactions within the thallus margin and the maintenance of symmetry in the lichen Parmelia conspersa (Ehrh. ex Ach.)Ach.

This study determined whether the radial growth of lobes of the foliose lichen Parmelia conspersa (Ehrh. ex Ach.)Ach. was influenced by the radial growth and morphology of their closest neighbours and whether such interactions influence thallus symmetry. The radial growth and morphology of a sample of adjacent lobes from six thalli was measured. Positive correlations were observed between radial growth and lobe width in three thalli and with the degree of bifurcation of the lobe in two thalli. Negative correlations between the radial growth of adjacent lobes were observed in four thalli suggesting that faster growing lobes may inhibit the growth of their neighbours.Lobes glued next to individual lobes had no signifiacnt effect on the radial growth of wide or narrow lobes. Lobes glued 1-2 mm in front of their neighbours exhibited an intital phase of increased radial growth and then a phase of slower growth. Radial growth decreased when the lobes were glued 2 mm behind their neighbours and these lobes were essentially eliminated by the growth of the adjacent lobes. The data suggest that lobe interactions may incresae lobe growth variation within a thallus. However, the decrease in radial growth of lobes which protrude from the margin and the elimination of slower growing lobes may help to maintain thallus symmetry.

Lobe connections and lobe crowding are associated with growth rate in the lichen Xanthoparmelia conspersa

The association between lobe connections and the degree of lobe crowding and radial growth was studied in thalli of the foliose lichen Xanthoparmelia conspersa. In 35 thalli, 15% of the lobes were not physically connected to either of their neighbours before the lobes merged into the centre of the thallus. Twenty-five percent of the lobes were connected in pairs and 29% in groups of three. Approximately 5% of the lobes were interconnected in larger groups of six or more. The mean number of lobes per group in a thallus was positively correlated with thallus diameter and with the degree of lobe growth variation but was unrelated to annual radial growth rate (RGR). The degree of crowding of the lobes in a thallus was defined as a 'crowding index', viz., the product of lobe density and mean lobe width. Crowding index increased rapidly with size in smaller thalli but changed less with size in larger thalli. Crowding index was positively correlated with RGR but was unrelated to lobe growth variation. Lobes removed from large thalli and glued in various configurations to simulate different degrees of crowding did not demonstrate an association between lobe crowding and RGR over one year. These results suggest that the pattern of lobe connectivity of a thallus is associated with lobe growth variation in X. conspersa. The degree of lobe crowding is associated with the increase in RGR with thallus size in smaller thalli and by restricting lobe width, could also be a factor associated with the more constant growth of larger thalli.

Competition between three lichen species using a factorial experimental design

Competition between three foliose lichens common on slate rock in south Gwynedd, Wales was studied in the field using a factorial experimental design. The lichens were grown as fragments glued to pieces of slate in two- and three-species mixtures. In the two-species mixtures, Parmelia conspersa (Ehrh. Ex Ach.) Ach. outcompeted Parmelia glabratula ssp. fuliginosa (Fr. ex Duby) Laund. strongly and Physcia orbicularis (Neck.) Poetsch less strongly, while P. orbicularis outcompeted P. glabratula weakly. Significant two-factor interactions indicated that the results from the three-species mixture could not be predicted from the two-species mixtures. Parmelia glabratula and P. orbicularis grew better in the presence of two competitors than one. This result suggests that the three species may co-occur on well-lit rock surfaces at the site.

The retromer coat complex coordinates endosomal sorting and dynein-mediated transport, with carrier recognition by the trans-Golgi network

Early endosome-to-trans-Golgi network (TGN) transport is organized by the retromer complex. Consisting of cargo-selective and membrane-bound subcomplexes, retromer coordinates sorting with membrane deformation and carrier formation. Here, we describe four mammalian retromers whose membrane-bound subcomplexes contain specific combinations of the sorting nexins (SNX), SNX1, SNX2, SNX5, and SNX6. We establish that retromer requires a dynamic spatial organization of the endosomal network, which is regulated through association of SNX5/SNX6 with the p150(glued) component of dynactin, an activator of the minus-end directed microtubule motor dynein; an association further defined through genetic studies in C. elegans. Finally, we also establish that the spatial organization of the retromer pathway is mediated through the association of SNX1 with the proposed TGN-localized tether Rab6-interacting protein-1. These interactions describe fundamental steps in retromer-mediated transport and establish that the spatial organization of the retromer network is a critical element required for efficient retromer-mediated sorting.

Factors associated with lobe division in the lichen Parmelia conspersa (Ehrh. ex. Ach.)Ach.

The factors associated with lobe division were studied in thalli of the lichen Parmelia conspersa (Ehrh. ex Ach.)Ach. Lobe division was studied in sequences of adjacent lobes using spatial pattern analysis. In five large thalli, lobe division within the thallus margin was randomly distributed. Correlations between the degree of lobe division, the radial growth of the lobe and lobe morphology were studied in six thalli. Lobe division was positively correlated with either lobe width or area in four thalli. Correlations were observed with radial growth or morphology of the adjacent lobes in two thalli. Dividing and non-dividing lobes were removed from large thalli and glued to pieces of slate with their tips either at the same level or in front of neighbouring lobes. Dividing lobes divided more rapidly when their tips were glued in front of their neighbours. The levels of ribitol, arabitol and mannitol were measured within a 2 mm region of the tip in dividing and non-dividing lobes on four occasions in 1994. Carbohydrate levels were significantly increased in dividing compared with non-dividing lobes. In addition, the mean size of the algal cells was greater in non-dividing compared with dividing lobes especially at the lobe base. However, the percentage of zoosporangia and aplanosporangia did not vary significantly in dividing and non-dividing lobes. These results suggest that: 1) the pattern of lobe division within the thallus margin may be random, 2) lobe division may be determined by lobe size and the location of the lobe tip relative to the neighbouring lobes and 3) there may be an increase in the productivity of lobes associated with lobe division.

The growth of six saxicolous lichens transplanted to lime-rich and lime-poor substrates in south Gwynedd, Wales

The objectives of this study were to investigate: (1) whether foliose lichen thalli could be transplanted from one substrate to another and (2) whether such transplants could be used to study the influence of the substrate on growth. Hence, six saxicolous lichens, with contrasting distributions on lime-rich and lime-poor substrates in South Gwynedd, Wales, were transplanted onto slate, granite, asbestos and cement. Fragments of the perimeters of thalli were glued to the different substrates using Bostic adhesive. Parmelia conspersa (Ehrh. Ex Ach.)Ach. and Parmelia saxatilis (L.)Ach., fragments increased in area over 15 months on slate and granite but decreased in area or did not survive on asbestos and cement. Fragments of Xanthoria parietina (L.)Th.Fr. and Physcia tenella (Scop.)DC. em Bitt. did not survive on slate and granite while some fragments survived but grew poorly on asbestos and cement. Parmelia glabratula ssp. fuliginosa (Fr. ex Duby)Laund. fragments decreased in area on all substrates and especially on cement and asbestos while Physcia orbicularis (Neck.)Poetsch fragments increased in area on granite and cement, decreased on asbestos and did not change significantly on slate. The results suggested that the distribution of P. conspersa and P. saxatilis was determined primarily by physico-chemical properties of the substrate. By contrast, P. glabratula ssp. fuliginosa may have responded to the transplant procedure while X. parietina, Ph. tenella and Ph. orbicularis may require nutrient enrichment to grow successfully on a substrate.

A comparison of the growth curves of the foliose lichen Parmelia conspersa determined by a cross-sectional study and by direct measurement

Changes in the radial growth rate (RGR mm/yr) through life were studied in thalli of the foliose lichen Parmelia conspersa by two methods: (1) a cross-sectional study (Study A) in which the RGR was measured in 60 thalli from 0.2 to 13 cm in diameter, and (2) by radial growth measurements over 4.5 years of fragments, consisting of a single major lobe, which were removed from large thalli and glued to pieces of slate (Study B). Both studies suggested there was a phase of increasing RGR in small thalli followed by a more constant phase, the latter beginning at approximately a thallus radius of 6-8 mm. However, in Study B significantly increased RGR was observed during the second 6-month growth period. This phase of growth was more likely to be due to an increase in lobe width than to an effect of climate. In addition, a lobe in a large thallus with both adjacent lobes removed significantly increased in width over 1 year compared with control lobes. These results suggest that (1) mean lobe width in a thallus may be determined by the intensity of marginal competition between adjacent lobes, and (2) changes in lobe width during the life of a lichen thallus may be a factor determining the establishment of the linear phase of growth in foliose lichens. © 1992.

Competitive interactions between four foliose lichens on north and south facing rock surfaces

Competition between four foliose lichen species which have distinct aspect distributions on slate rock in South Gwynedd, Wales, U.K. was studied in the field using a factorial experimental design. The lichens were grown as fragments glued to pieces of slate in monoculture and in two-, three- and four-species mixtures. The pieces of slate were placed to face a northerly or southerly direction. Growth in area (mm2) was used as a measure of performance in the experiment. The growth in area of Parmelia conspersa in south facing plots was not reduced in the presence of any of its competitors but its growth was reduced in the presence of Parmelia saxatilis in north facing plots. The growth of Parmelia glabratula ssp. fuliginosa was reduced in the presence of P. conspersa and P. saxatilis in south and north facing plots. Physcia orbicularis was reduced by P. conspersa in south facing plots and by both P. glabratula ssp. fuliginosa and P. saxatilis in north facing plots. The growth of P. saxatilis was increased by P. glabratula ssp. fuliginosa in south facing plots but was not reduced by any of its competitors in north facing plots. Significant two and three factor interactions suggested that the results from the three- and four-species mixtures were not always predictable from the results of the two-species mixtures. The results of the experiment may help to explain the existing aspect distribution of the four species on slate rock in South Gwynedd.

Competition between three saxicolous species of Parmelia (lichens)

Fragments of three foliose, saxicolous lichens were glued in 5 x 5 cm plots on pieces of slate in the field, either in monoculture or paired in 1:1 mixtures with each of the other two species. A preliminary experiment suggested that glueing did not influence the radial growth of the lichen fragments. No species eliminated another after 3 years but the growth (total area in sq mm) of Parmelia saxatils and P. glabratula ssp. fuliginosa was reduced significantly in mixtures with P. conspersa; the growth of P. glabratula ssp. fuliginosa was reduced significantly in the mixture with P. saxatilis compared with their growth in monoculture. The results suggest that the three lichens show interference by competition for space and light in the following order of competitive ability: P. conspersa > P. saxatilis > P. glabratula ssp. fuliginosa. A high radial growth rate and the ability to overgrow a thallus may be important competitive attributes in foliose lichens and the results also suggest that competition can reduce the abundance of a lichen and lead to distribution patterns in the field.

Lobe formation and division in the foliose lichen Xanthoparmelia conspersa

New lobe development and lobe division was studied in the foliose lichen Xanthoparmelia conspersa (Ehrh. ex. Ach.) Hale. In thalli with either the centre or margin removed, the inside edge of the perimeter, the outer edge of the reproductive centre, and fragments derived from the thallus perimeter all regenerated growing points (‘lobe primordia’) within a year. Thalli possessing isidia had the greatest ability to regenerate growing points. In reproductive thalli, there was a positive correlation between the density of new growing points and thallus size. When fragments were cut from the perimeters of mature X. conspersa thalli and glued to pieces of slate, the ratio of growing points to mature lobes increased over 54 months. Lobes within a thallus exhibited different degrees of bifurcation. In some bifurcating lobes, the point of origin of the bifurcation advanced at the same rate as the lobe tips over 4 months but in most lobes, the bifurcation point either advanced less rapidly than the lobe tips or retreated from its original location. Removing adjacent lobes had no significant effect on the radial growth of a lobe over 4 months or on the location of the bifurcation point but it increased the number of growing points. These results suggest that for X. conspersa: 1) all portions of of thalli can regenerate growing points, 2) few growing points actually develop into mature lobes, 3) individual lobes within a thallus grow and divide differently, and 4) adjacent lobes inhibit the development of growing points on their neighbours.

The mechanical behaviour of cylindrical GRP panels

Glass reinforced plastic (GRP) is now an established material for the fabrication of sonar windows. Its good mechanical strength, light weight, resistance to corrosion and acoustic transparency, are all properties which fit it for this application. This thesis describes a study, undertaken at the Royal Naval Engineering College, Plymouth, into the mechanical behaviour of a circular cylindrical sonar panel. This particular type of panel would be used to cover a flank array sonar in a ship or submarine. The case considered is that of a panel with all of its edges mechanically clamped and subject to pressure loading on its convex surface. A comprehensive program of testing, to determine the orthotropic elastic properties of the laminated composite panel material is described, together with a series of pressure tests on 1:5 scale sonar panels. These pressure tests were carried out in a purpose designed test rig, using air pressure to provide simulated hydrostatic and hydrodynamic loading. Details of all instrumentation used in the experimental work are given in the thesis. The experimental results from the panel testing are compared with predictions of panel behaviour obtained from both the Galerkin solution of Flugge's cylindrical shell equations (orthotropic case), and finite element modelling of the panels using PAFEC. A variety of appropriate panel boundary conditions are considered in each case. A parametric study, intended to be of use as a preliminary design tool, and based on the above Galerkin solution, is also presented. This parametric study considers cases of boundary conditions, material properties, and panel geometry, outside of those investigated in the experimental work Final conclusions are drawn and recommendations made regarding possible improvements to the procedures for design, manufacture and fixing of sonar panels in the Royal Navy.