The investigation of vegetation change using remote sensing to detect and monitor migration of landfill gas

Decomposition of domestic wastes in an anaerobic environment results in the production of landfill gas. Public concern about landfill disposal and particularly the production of landfill gas has been heightened over the past decade. This has been due in large to the increased quantities of gas being generated as a result of modern disposal techniques, and also to their increasing effect on modern urban developments. In order to avert diasters, effective means of preventing gas migration are required. This, in turn requires accurate detection and monitoring of gas in the subsurface. Point sampling techniques have many drawbacks, and accurate measurement of gas is difficult. Some of the disadvantages of these techniques could be overcome by assessing the impact of gas on biological systems. This research explores the effects of landfill gas on plants, and hence on the spectral response of vegetation canopies. Examination of the landfill gas/vegetation relationship is covered, both by review of the literature and statistical analysis of field data. The work showed that, although vegetation health was related to landfill gas, it was not possible to define a simple correlation. In the landfill environment, contribution from other variables, such as soil characteristics, frequently confused the relationship. Two sites are investigated in detail, the sites contrasting in terms of the data available, site conditions, and the degree of damage to vegetation. Gas migration at the Panshanger site was dominantly upwards, affecting crops being grown on the landfill cap. The injury was expressed as an overall decline in plant health. Discriminant analysis was used to account for the variations in plant health, and hence the differences in spectral response of the crop canopy, using a combination of soil and gas variables. Damage to both woodland and crops at the Ware site was severe, and could be easily related to the presence of gas. Air photographs, aerial video, and airborne thematic mapper data were used to identify damage to vegetation, and relate this to soil type. The utility of different sensors for this type of application is assessed, and possible improvements that could lead to more widespread use are identified. The situations in which remote sensing data could be combined with ground survey are identified. In addition, a possible methodology for integrating the two approaches is suggested.

Individual differences in work behaviour of blue-collar workers : a study of rubber tappers in Malaysia

This thesis examines individual differences in work behaviour of rubber tappers. The study examined sex, age, experience and race differences and their interactions with terrain on job performance, absenteeism, and job satisfaction of 1053 rubber tappers. Rubber tappers are unskilled blue-collar workers who essentially do the same type of work and are paid the same rates of pay. There are very few studies that have compared male and female blue-collar workers doing similar jobs in organisational settings. This study is one of the few investigations that examine sex differences in job performance of blue-collar workers doing same job using production data. Studies on age differences in work behaviour encounter numerous methodological difficulties such as high turnover, internal transfers and problems associated with age differences in educational levels. The participation of rubber tappers in this study is envisaged to overcome these difficulties because attrition rates of rubber tappers are low, and internal transfers are non existent. Further, the educational levels of rubber tappers are relatively similar across different age cohorts, as most rubber tappers have little or no education. Two measures of both job performance and absenteeism were derived from payroll records. The two job performance measures were total crop production and attendance. The two absenteeism measures were avoidable and unavoidable absence rates. Overall job satisfaction was determined using a 4-item scale. Significant sex, age, experience and race differences were obtained for job performance, absenteeism and job satisfaction. Significant interactive effects were also obtained for sex, age , experience, race and terrain for job performance and absenteeism. The results are discussed in relation to the abilities and motivation of rubber tappers. The implication of these findings for employee selection and human resource management in rubber estates is discussed.

Fair testing in employment selection

This project represents the collaboration of Charta Mede Ltd and the Interdisciplinary Higher Degrees Scheme at the University of Aston. The aim of the project was to monitor the effects of the Civil Service's Executive Officer Qualifying Test Battery on minority group applicants. Prior to monitoring the EO Test Battery, however, an ethnic classification had to be developed which was reliable, acceptable to respondents and appropriate for monitoring. Three pilot studies were conducted to examine these issues, during which different classifications and different ways of asking the question were trialled. The results indicated that by providing more precise instructions as to the meanings of categories, it was possible to obtain classifications which were acceptable and reliable. However, there were also certain terms and expressions which should be avoided such as those referring to colour and anthropological racial groups. Two classifications were used in the Executive Officer Study - one derived from an Office of Population Censuses and Surveys classification and one developed for this project - the MultiCultural British Classification. The results indicated that some minority groups (Asians, West Indians and Africans in particular) pass the tests in significantly lower proportions than the majority group and also score significantly less well on the tests. Factors which were significantly related to pass/fail and test scores included educational qualifications and age on entering the UK (the latter being negatively correlated). Using variables in this study, however, it was only possible to account for 5% of the variance in pass/fail rates and 11% of the variance in test scores. Analyses of covariance carried out indicated that the differences in test scores still remained even though the effects of significantly correlated variables were removed. Although indirect discrimination could not be inferred from the data, further research into differential validity and fairer methods of select ion is needed.

The application of remote sensing to the management of urban wildlife habitats

The project set out with two main aims. The first aim was to determine whether large scale multispectral aerial photography could be used to successfully survey and monitor urban wildlife habitats. The second objective was to investigate whether this data source could be used to predict population numbers of selected species expected to be found in a particular habitat type. Panchromatic, colour and colour infra-red, 1:2500 scale aerial photographs, taken in 1981 and 1984, were used. For the orderly extraction of information from the imagery, an urban wildlife habitat classification was devised. This was based on classifications already in use in urban environments by the Nature Conservancy Council. Pilot tests identified that the colour infra-red imagery provided the most accurate results about urban wildlife habitats in the study area of the Blackbrook Valley, Dudley. Both the 1981 and 1984 colour infra-red photographs were analysed and information was obtained about the type, extent and distribution of habitats. In order to investigate whether large scale aerial photographs could be used to predict likely animal population numbers in urban environments, it was decided to limit the investigation to the possible prediction of bird population numbers in Saltwells Local Nature Reserve. A good deal of research has already been completed into the development of models to predict breeding bird population numbers in woodland habitats. These models were analysed to determine whether they could be used successfully with data extracted from the aerial photographs. The projects concluded that 1:2500 scale colour infra-red photographs can provide very useful and very detailed information about the wildlife habitats in an urban area. Such imagery can also provide habitat area data to be used with population predictive models of woodland breeding birds. Using the aerial photographs, further investigations into the relationship between area of habitat and the breeding of individual bird species were inconclusive and need further research.

A low-cost remote sensing system for agricultural applications

This research develops a low cost remote sensing system for use in agricultural applications. The important features of the system are that it monitors the near infrared and it incorporates position and attitude measuring equipment allowing for geo-rectified images to be produced without the use of ground control points. The equipment is designed to be hand held and hence requires no structural modification to the aircraft. The portable remote sensing system consists of an inertia measurement unit (IMU), which is accelerometer based, a low-cost GPS device and a small format false colour composite digital camera. The total cost of producing such a system is below GBP 3000, which is far cheaper than equivalent existing systems. The design of the portable remote sensing device has eliminated bore sight misalignment errors from the direct geo-referencing process. A new processing technique has been introduced for the data obtained from these low-cost devices, and it is found that using this technique the image can be matched (overlaid) onto Ordnance Survey Master Maps at an accuracy compatible with precision agriculture requirements. The direct geo-referencing has also been improved by introducing an algorithm capable of correcting oblique images directly. This algorithm alters the pixels value, hence it is advised that image analysis is performed before image georectification. The drawback of this research is that the low-cost GPS device experienced bad checksum errors, which resulted in missing data. The Wide Area Augmented System (WAAS) correction could not be employed because the satellites could not be locked onto whilst flying. The best GPS data were obtained from the Garmin eTrex (15 m kinematic and 2 m static) instruments which have a highsensitivity receiver with good lock on capability. The limitation of this GPS device is the inability to effectively receive the P-Code wavelength, which is needed to gain the best accuracy when undertaking differential GPS processing. Pairing the carrier phase L1 with the pseudorange C/A-Code received, in order to determine the image coordinates by the differential technique, is still under investigation. To improve the position accuracy, it is recommended that a GPS base station should be established near the survey area, instead of using a permanent GPS base station established by the Ordnance Survey.

The selection of biodiversity indicators for business landholdings

Businesses are seen as the next stage in delivering biodiversity improvements linked to local and UK Biodiversity Action Plans. Global discussion of biodiversity continues to grow, with the Millennium Ecosystem Assessment, updates to the Convention on Biological Diversity and The Economics of Ecosystems and Biodiversity being published during the time of this project. These publications and others detail the importance of biodiversity protection and also the lack of strategies to deliver this at an operational level. Pressure on UK landholding businesses is combined with significant business opportunities associated with biodiversity engagement. However, the measurement and reporting of biodiversity by business is currently limited by the complexity of the term and the lack of suitable procedures for the selection of metrics. Literature reviews identified confusion surrounding biodiversity as a term, limited academic literature regarding business and choice of biodiversity indicators. The aim of the project was to develop a methodology to enable companies to identify, quantify and monitor biodiversity. Research case studies interviews were undertaken with 10 collaborating organisations, selected to represent =best practice‘ examples and various situations. Information gained through case studies was combined with that from existing literature. This was used to develop a methodology for the selection of biodiversity indicators for company landholdings. The indicator selection methodology was discussed during a second stage of case study interviews with 4 collaborating companies. The information and opinions gained during this research was used to modify the methodology and provide the final biodiversity indicator selection methodology. The methodology was then tested through implementation at a mineral extraction site operated by a multi-national aggregates company. It was found that the methodology was a suitable process for implementation of global and national systems and conceptual frameworks at the practitioner scale. Further testing of robustness by independent parties is recommended to improve the system.

Visualisation of quality information for geospatial and remote sensing data:providing the GIS community with the decision support tools for geospatial dataset quality evaluation

The evaluation of geospatial data quality and trustworthiness presents a major challenge to geospatial data users when making a dataset selection decision. The research presented here therefore focused on defining and developing a GEO label – a decision support mechanism to assist data users in efficient and effective geospatial dataset selection on the basis of quality, trustworthiness and fitness for use. This thesis thus presents six phases of research and development conducted to: (a) identify the informational aspects upon which users rely when assessing geospatial dataset quality and trustworthiness; (2) elicit initial user views on the GEO label role in supporting dataset comparison and selection; (3) evaluate prototype label visualisations; (4) develop a Web service to support GEO label generation; (5) develop a prototype GEO label-based dataset discovery and intercomparison decision support tool; and (6) evaluate the prototype tool in a controlled human-subject study. The results of the studies revealed, and subsequently confirmed, eight geospatial data informational aspects that were considered important by users when evaluating geospatial dataset quality and trustworthiness, namely: producer information, producer comments, lineage information, compliance with standards, quantitative quality information, user feedback, expert reviews, and citations information. Following an iterative user-centred design (UCD) approach, it was established that the GEO label should visually summarise availability and allow interrogation of these key informational aspects. A Web service was developed to support generation of dynamic GEO label representations and integrated into a number of real-world GIS applications. The service was also utilised in the development of the GEO LINC tool – a GEO label-based dataset discovery and intercomparison decision support tool. The results of the final evaluation study indicated that (a) the GEO label effectively communicates the availability of dataset quality and trustworthiness information and (b) GEO LINC successfully facilitates ‘at a glance’ dataset intercomparison and fitness for purpose-based dataset selection.

The automation of protein crystal presentation for x ray diffraction experiments using standing acoustic waves in a microfluidic chip environment

As the pressure continues to grow on Diamond and the world's synchrotrons for higher throughput of diffraction experiments, new and novel techniques are required for presenting micron dimension crystals to the X ray beam. Currently this task is both labour intensive and primarily a serial process. Diffraction measurements typically take milliseconds but sample preparation and presentation can reduce throughput down to 4 measurements an hour. With beamline waiting times as long as two years it is of key importance for researchers to capitalize on available beam time, generating as much data as possible. Other approaches detailed in the literature [1] [2] [3] are very much skewed towards automating, with robotics, the actions of a human protocols. The work detailed here is the development and discussion of a bottom up approach relying on SSAW self assembly, including material selection, microfluidic integration and tuning of the acoustic cavity to order the protein crystals.

The automation of protein crystal presentation for X ray diffraction experiments using standing acoustic waves in a microfluidic chip environment

As the pressure continues to grow on Diamond and the world's synchrotrons for higher throughput of diffraction experiments, new and novel techniques are required for presenting micron dimension crystals to the X ray beam. Currently this task is both labour intensive and primarily a serial process. Diffraction measurements typically take milliseconds but sample preparation and presentation can reduce throughput down to 4 measurements an hour. With beamline waiting times as long as two years it is of key importance for researchers to capitalize on available beam time, generating as much data as possible. Other approaches detailed in the literature [1] [2] [3] are very much skewed towards automating, with robotics, the actions of a human protocols. The work detailed here is the development and discussion of a bottom up approach relying on SSAW self assembly, including material selection, microfluidic integration and tuning of the acoustic cavity to order the protein crystals.