Oxidation of protein in human low-density lipoprotein exposed to peroxyl radicals facilitates uptake by monocytes; protection by antioxidants in vitro

Generation of neoepitopes on apolipoprotein B within oxidised low-density lipoprotein (LDL) is important in the unregulated uptake of LDL by monocytic scavenger receptors (CD36, SR-AI, LOX-1). Freshly isolated LDL was oxidised by peroxyl radicals generated from the thermal decomposition of an aqueous azo-compound. We describe that formation of carbonyl groups on the protein component is early as protein oxidation was seen after 90min. This is associated with an increased propensity for LDL uptake by U937 monocytes. Three classes of antioxidants (quercetin, dehydroepiandrosterone (DHEA) and ascorbic acid) have been examined for their capacity to inhibit AAPH-induced protein oxidation, (protein carbonyls, Δ electrophoretic mobility and LDL uptake by U937 monocytes). CD36 expression was assessed by flow cytometry and was seen to be unaltered by oxidised LDL uptake. All three classes were effective antioxidants, quercetin (P<0.01), ascorbic acid (P<0.01), DHEA (P<0.05). As LDL protein is the control point for LDL metabolism, the degree of oxidation and protection by antioxidants is likely to be of great importance for (patho)-physiological uptake of LDL by monocytes. © 2003 Elsevier B.V. All rights reserved.

Microarray analysis of expression of cell death-associated genes in rat spinal cord cells exposed to cyclic tensile stresses in vitro

The application of mechanical insults to the spinal cord results in profound cellular and molecular changes, including the induction of neuronal cell death and altered gene expression profiles. Previous studies have described alterations in gene expression following spinal cord injury, but the specificity of this response to mechanical stimuli is difficult to investigate in vivo. Therefore, we have investigated the effect of cyclic tensile stresses on cultured spinal cord cells from E15 Sprague-Dawley rats, using the FX3000 Flexercell Strain Unit. We examined cell morphology and viability over a 72 hour time course. Microarray analysis of gene expression was performed using the Affymetrix GeneChip System, where categorization of identified genes was performed using the Gene Ontology (GO) and Kyoto Encyclopedia of Genes and Genomes (KEGG) systems. Changes in expression of 12 genes were validated with quantitative real-time reverse transcription polymerase chain reaction (RT-PCR).

What does endogenous growth theory tell about regional economies? Empirics of R&D worker-based productivity growth

What does endogenous growth theory tell about regional economies? Empirics of R&D worker-based productivity growth, Regional Studies. Endogenous growth theory emerged in the 1990s as ‘new growth theory’ accounting for technical progress in the growth process. This paper examines the role of research and development (R&D) workers underlying the Romer model (1990) and its subsequent modifications, and compares it with a model based on the accumulation of human capital engaged in R&D. Cross-section estimates of the models against productivity growth of European regions in the 1990s suggest that each R&D worker has a unique set of knowledge while his/her contributions are enhanced by knowledge sharing within a region as well as spillovers from other regions in proximity.

Languaging the worker:globalized governmentalities in/of language in peripheral spaces

In the introduction to the special issue “Languaging the worker: globalized governmentalities in/of language in peripheral spaces”, we take up the notion of governmentality as a means to interrogate the complex relationship between language, labor, power and subjectivity in peripheral multilingual spaces. Our aim here is to argue for the study of governmentality as a viable and growing approach in critical sociolinguistic research. As such, in this introduction, we first discuss key concepts germane to our interrogations, including the notions of governmentality, languaging, peripherality and language worker. We proceed to map out five ethnographically and discourse-analytically informed case studies. These examine diverse actors in different settings pertaining to the domain of work. Finally we chart how the case studies construe the issue of languaging the worker through a governmentality frame.

Mitochondrial superoxide anion radicals mediate induction of apoptosis in cardiac myoblasts exposed to chronic hypoxia

Both reactive oxygen species (ROS) and ATP depletion may be significant in hypoxia-induced damage and death, either collectively or independently, with high energy requiring, metabolically active cells being the most susceptible to damage. We investigated the kinetics and effects of ROS production in cardiac myoblasts, H9C2 cells, under 2%, 10% and 21% O2 in the presence or absence of apocynin, rotenone and carbonyl cyanide p-(trifluoromethoxy) phenylhydrazone. H9C2 cells showed significant loss of viability within 30 min of culture at 2% oxygen which was not due to apoptosis, but was associated with an increase in protein oxidation. However, after 4 h, apoptosis induction was observed at 2% oxygen and also to a lesser extent at 10% oxygen; this was dependent on the levels of mitochondrial superoxide anion radicals determined using dihydroethidine. Hypoxia-induced ROS production and cell death could be rescued by the mitochondrial complex I inhibitor, rotenone, despite further depletion of ATP. In conclusion, a change to superoxide anion radical steady state level was not detectable after 30 min but was evident after 4 h of mild or severe hypoxia. Superoxide anion radicals from the mitochondrion and not ATP depletion is the major cause of apoptotic cell death in cardiac myoblasts under chronic, severe hypoxia.

Coupled heat and mass transfer in concrete exposed to fire

The first investigation of this study is concerned with the reasonableness of the assumptions related to diffusion of water vapour in concrete and with the development of a diffusivity equation for heated concrete. It has been demonstrated that diffusion of water vapour does occur in concrete at all temperatures and that the type of diffusion is concrete is Knudsen diffusion. Neglecting diffusion leads to underestimating the pressure. It results in a maximum pore pressure of less than 1 MPa. It has also been shown that the assumption that diffusion in concrete is molecular is unreasonable even when the tortuosity is considered. Molecular diffusivity leads to overestimating the pressure. It results in a maximum pore pressure of 2.7 MPa of which the vapour pressure is 1.5 MPa while the air pressure is 1.2 MPa. Also, the first diffusivity equation, appropriately named 'concrete diffusivity', has been developed specifically for concrete that determines the effective diffusivity of any gas in concrete at any temperature. In thick walls and columns exposed to fire, concrete diffusivity leads to a maximum pore pressures of 1.5 and 2.2 MPa (along diagonals), respectively, that are almost entirely due to water vapour pressure. Also, spalling is exacerbated, and thus higher pressures may occur, in thin heated sections, since there is less of a cool reservoir towards which vapour can migrate. Furthermore, the reduction of the cool reservoir is affected not only by the thickness, but also by the time of exposure to fire and by the type of exposure, i.e. whether the concrete member is exposed to fire from one or more sides. The second investigation is concerned with examining the effects of thickness and exposure time and type. It has been demonstrated that the build up of pore pressure is low in thick members, since there is a substantial cool zone towards which water vapour can migrate. Thus, if surface and/or explosive spalling occur on a thick member, then such spalling must be due to high thermal stresses, but corner spalling is likely to be pore pressure spalling. However, depending on the exposure time and type, the pore pressures can be more than twice those occurring in thick members and thought to be the maximum that can occur so far, and thus the enhanced propensity of pore pressure spalling occurring on thin sections heated on opposite sides has been conclusively demonstrated to be due to the lack of a cool zone towards which moisture can migrate. Expressions were developed for the determination of the maximum pore pressures that can occur in different concrete walls and columns exposed to fire and of the corresponding times of exposure.

Influence of impact angles on penetration rates of CRAs exposed to a high velocity multiphase flow

A combined flow loop - jet impingement pilot plant has been used to determine mass loss rates in a mixed gas - saltwater - sand multiphase flow at impact velocities up to 70 m/s. Artificial brine with a salt content of 27 g/1 was used as liquid phase. Sand content, with grain size below 150 µ, was 2.7 g/l brine. CO at a pressure of 15 bar was used as gas phase. The impact angle between jet stream (nozzle) and sample surface was varied between 30 and 90°. Rectangular stainless steel disc samples with a size of 20 × 15 × 5 mm were used. They were mechanically ground and polished prior to testing. Damaged surfaces of specimens exposed to the high velocity multiphase flow were investigated by stereo microscopy, scanning electron microscopy (SEM) and an optical device for 3D surface measurements. Furthermore, samples were investigated by applying atomic force microscopy (AFM), magnetic force microscopy (MFM) and nanoindentation. Influence of impact velocity and impact angle on penetration rates (mass loss rates) of two CRAs (UNS S30400 and N08028) are presented. Moreover effects of chemical composition and mechanical properties are critically discussed. © 2008 by NACE International.

Using empirical evidence of variations in worker performance to extend the capabilities of discrete event simulations in manufacturing

Discrete event simulation of manufacturing systems has become widely accepted as an important tool to aid the design of such systems. Often, however, it is applied by practitioners in a manner which largely ignores an important element of industry; namely, the workforce. Workers are usually represented as simple resources, often with deterministic performance values. This approach ignores the potentially large effect that human performance variation can have on a system. A long-term data collection exercise is described with the aim of quantifying the performance variation of workers in a typical automotive assembly plant. The data are presented in a histogram form which is immediately usable in simulations to improve the accuracy of design assessment. The results show levels of skewness and range which are far larger than anticipated by current researchers and practitioners in the field.