Use of computational fluid dynamics in the design of bubble column reactors

Investigations into the modelling techniques that depict the transport of discrete phases (gas bubbles or solid particles) and model biochemical reactions in a bubble column reactor are discussed here. The mixture model was used to calculate gas-liquid, solid-liquid and gasliquid-solid interactions. Multiphase flow is a difficult phenomenon to capture, particularly in bubble columns where the major driving force is caused by the injection of gas bubbles. The gas bubbles cause a large density difference to occur that results in transient multi-dimensional fluid motion. Standard design procedures do not account for the transient motion, due to the simplifying assumptions of steady plug flow. Computational fluid dynamics (CFD) can assist in expanding the understanding of complex flows in bubble columns by characterising the flow phenomena for many geometrical configurations. Therefore, CFD has a role in the education of chemical and biochemical engineers, providing the examples of flow phenomena that many engineers may not experience, even through experimentation. The performance of the mixture model was investigated for three domains (plane, rectangular and cylindrical) and three flow models (laminar, k-e turbulence and the Reynolds stresses). mThis investigation raised many questions about how gas-liquid interactions are captured numerically. To answer some of these questions the analogy between thermal convection in a cavity and gas-liquid flow in bubble columns was invoked. This involved modelling the buoyant motion of air in a narrow cavity for a number of turbulence schemes. The difference in density was caused by a temperature gradient that acted across the width of the cavity. Multiple vortices were obtained when the Reynolds stresses were utilised with the addition of a basic flow profile after each time step. To implement the three-phase models an alternative mixture model was developed and compared against a commercially available mixture model for three turbulence schemes. The scheme where just the Reynolds stresses model was employed, predicted the transient motion of the fluids quite well for both mixture models. Solid-liquid and then alternative formulations of gas-liquid-solid model were compared against one another. The alternative form of the mixture model was found to perform particularly well for both gas and solid phase transport when calculating two and three-phase flow. The improvement in the solutions obtained was a result of the inclusion of the Reynolds stresses model and differences in the mixture models employed. The differences between the alternative mixture models were found in the volume fraction equation (flux and deviatoric stress tensor terms) and the viscosity formulation for the mixture phase.

A comparison of linear forecasting models and neural networks:an application to Euro inflation and Euro Divisia

Linear models reach their limitations in applications with nonlinearities in the data. In this paper new empirical evidence is provided on the relative Euro inflation forecasting performance of linear and non-linear models. The well established and widely used univariate ARIMA and multivariate VAR models are used as linear forecasting models whereas neural networks (NN) are used as non-linear forecasting models. It is endeavoured to keep the level of subjectivity in the NN building process to a minimum in an attempt to exploit the full potentials of the NN. It is also investigated whether the historically poor performance of the theoretically superior measure of the monetary services flow, Divisia, relative to the traditional Simple Sum measure could be attributed to a certain extent to the evaluation of these indices within a linear framework. Results obtained suggest that non-linear models provide better within-sample and out-of-sample forecasts and linear models are simply a subset of them. The Divisia index also outperforms the Simple Sum index when evaluated in a non-linear framework. © 2005 Taylor & Francis Group Ltd.

Corporate restructuring: empirical evidence from the UK

Corporate restructuring is perceived as a challenge to research. Prior studies do not provide conclusive evidence regarding the effects of restructuring. Since there are discernible findings, this research attempts to examine the effects of restructuring events amongst the UK listed firms. The sample firms are listed in the LSE and London AIM stock exchange. Only completed restructuring transactions are included in the study. The time horizon extends from year 1999 to 2003. A three-year floating window is assigned to examine the sample firms. The key enquiry is to scrutinise the ex post effects of restructuring on performance and value measures of firms with contrast to a matched criteria non-restructured sample. A cross sectional study employing logit estimate is undertaken to examine firm characteristics of restructuring samples. Further, additional parameters, i.e. Conditional Volatility and Asymmetry are generated under the GJR-GARCH estimate and reiterated in logit models to capture time-varying heteroscedasticity of the samples. This research incorporates most forms of restructurings, while prior studies have examined certain forms of restructuring. Particularly, these studies have made limited attempts to examine different restructuring events simultaneously. In addition to logit analysis, an event study is adopted to evaluate the announcement effect of restructuring under both the OLS and GJR-GARCH estimate supplementing our prior results. By engaging a composite empirical framework, our estimation method validates a full appreciation of restructuring effect. The study provides evidence that restructurings indicate non-trivial significant positive effect. There are some evidences that the response differs because of the types of restructuring, particularly while event study is applied. The results establish that performance measures, i.e. Operating Profit Margin, Return on Equity, Return on Assets, Growth, Size, Profit Margin and Shareholders' Ownership indicate consistent and significant increase. However, Leverage and Asset Turn Over suggest reasonable influence on restructuring across the sample period. Similarly, value measures, i.e. Abnormal Returns, Return on Equity and Cash Flow Margin suggest sizeable improvement. A notable characteristic seen coherently throughout the analysis is the decreasing proportion of Systematic Risk. Consistent with these findings, Conditional Volatility and Asymmetry exhibit similar trend. The event study analysis suggests that on an average market perceives restructuring favourably and shareholders experience significant and systematic positive gain.

The use of maturity models in improving project management performance:an empirical investigation

Purpose – The purpose of the paper was to conduct an empirical investigation to explore the impact of project management maturity models (PMMMs) on improving project performance. Design/methodology/approach – The investigation used a cross-case analysis involving over 90 individuals in seven organisations. Findings – The findings of the empirical investigation indicate that PMMMs demonstrate very high levels of variability in individual's assessment of project management maturity. Furthermore, at higher levels of maturity, the type of performance improvement adopted following their application is related to the type of PMMM used in the assessment. The paradox of the unreliability of PMMMs and their widespread acceptance is resolved by calling upon the “wisdom of crowds” phenomenon which has implications for the use of maturity model assessments in other arena. Research limitations/implications – The investigation does have the usual issues associated with case research, but the steps that have been taken in the cross-case construction and analysis have improved the overall robustness and extendibility of the findings. Practical implications – The tendency for PMMMs to shape improvements based on their own inherent structure needs further understanding. Originality/value – The use of empirical methods to investigate the link between project maturity models and extant changes in project management performance is highly novel and the findings that result from this have added resonance.

EM optimization of latent-variable density models

There is currently considerable interest in developing general non-linear density models based on latent, or hidden, variables. Such models have the ability to discover the presence of a relatively small number of underlying `causes' which, acting in combination, give rise to the apparent complexity of the observed data set. Unfortunately, to train such models generally requires large computational effort. In this paper we introduce a novel latent variable algorithm which retains the general non-linear capabilities of previous models but which uses a training procedure based on the EM algorithm. We demonstrate the performance of the model on a toy problem and on data from flow diagnostics for a multi-phase oil pipeline.

Hydrodynamic modeling of mineral wool fiber suspensions in a two-dimensional flow

A consequence of a loss of coolant accident is that the local insulation material is damaged and maybe transported to the containment sump where it can penetrate and/or block the sump strainers. An experimental and theoretical study, which examines the transport of mineral wool fibers via single and multi-effect experiments is being performed. This paper focuses on the experiments and simulations performed for validation of numerical models of sedimentation and resuspension of mineral wool fiber agglomerates in a racetrack type channel. Three velocity conditions are used to test the response of two dispersed phase fiber agglomerates to two drag correlations and to two turbulent dispersion coefficients. The Eulerian multiphase flow model is applied with either one or two dispersed phases.

Empirical analysis of human capital development and economic growth in Europe

Recent discussion of the knowledge-based economy draws increasingly attention to the role that the creation and management of knowledge plays in economic development. Development of human capital, the principal mechanism for knowledge creation and management, becomes a central issue for policy-makers and practitioners at the regional, as well as national, level. Facing competition both within and across nations, regional policy-makers view human capital development as a key to strengthening the positions of their economies in the global market. Against this background, the aim of this study is to go some way towards answering the question of whether, and how, investment in education and vocational training at regional level provides these territorial units with comparative advantages. The study reviews literature in economics and economic geography on economic growth (Chapter 2). In growth model literature, human capital has gained increased recognition as a key production factor along with physical capital and labour. Although leaving technical progress as an exogenous factor, neoclassical Solow-Swan models have improved their estimates through the inclusion of human capital. In contrast, endogenous growth models place investment in research at centre stage in accounting for technical progress. As a result, they often focus upon research workers, who embody high-order human capital, as a key variable in their framework. An issue of discussion is how human capital facilitates economic growth: is it the level of its stock or its accumulation that influences the rate of growth? In addition, these economic models are criticised in economic geography literature for their failure to consider spatial aspects of economic development, and particularly for their lack of attention to tacit knowledge and urban environments that facilitate the exchange of such knowledge. Our empirical analysis of European regions (Chapter 3) shows that investment by individuals in human capital formation has distinct patterns. Those regions with a higher level of investment in tertiary education tend to have a larger concentration of information and communication technology (ICT) sectors (including provision of ICT services and manufacture of ICT devices and equipment) and research functions. Not surprisingly, regions with major metropolitan areas where higher education institutions are located show a high enrolment rate for tertiary education, suggesting a possible link to the demand from high-order corporate functions located there. Furthermore, the rate of human capital development (at the level of vocational type of upper secondary education) appears to have significant association with the level of entrepreneurship in emerging industries such as ICT-related services and ICT manufacturing, whereas such association is not found with traditional manufacturing industries. In general, a high level of investment by individuals in tertiary education is found in those regions that accommodate high-tech industries and high-order corporate functions such as research and development (R&D). These functions are supported through the urban infrastructure and public science base, facilitating exchange of tacit knowledge. They also enjoy a low unemployment rate. However, the existing stock of human and physical capital in those regions with a high level of urban infrastructure does not lead to a high rate of economic growth. Our empirical analysis demonstrates that the rate of economic growth is determined by the accumulation of human and physical capital, not by level of their existing stocks. We found no significant effects of scale that would favour those regions with a larger stock of human capital. The primary policy implication of our study is that, in order to facilitate economic growth, education and training need to supply human capital at a faster pace than simply replenishing it as it disappears from the labour market. Given the significant impact of high-order human capital (such as business R&D staff in our case study) as well as the increasingly fast pace of technological change that makes human capital obsolete, a concerted effort needs to be made to facilitate its continuous development.

Fibre agglomerate transport in a horizontal flow

An experimental and theoretical study of the transport of mineral wool fibre agglomerates in nuclear power plant containment sumps is being performed. A racetrack channel was devised to provide data for the validation of numerical models, which are intended to model the transport of fibre agglomerates. The racetrack channel provides near uniform and steady conditions that lead to either the sedimentation or suspension of the agglomerates. Various experimental techniques were used to determine the velocity conditions and the distribution of the fibre agglomerates in the channel. The fibre agglomerates are modelled as fluid particles in the Eulerian reference frame. Simulations of pure sedimentation of a known mass and volume of agglomerations show that the transport of the fibre agglomerates can be replicated. The suspension of the fibres is also replicated in the simulations; however, the definition of the fibre agglomerate phase is strongly dependent on the selected density and diameter. Detailed information on the morphology of the fibre agglomerates is lacking for the suspension conditions, as the fibre agglomerates may undergo breakage and erosion. Therefore, ongoing work, which is described here, is being pursued to improve the experimental characterisation of the suspended transport of the fibre agglomerates.

The valuation of travel time savings in least developed countries:theoretical and empirical challenges and results from a field study

In developed countries travel time savings can account for as much as 80% of the overall benefits arising from transport infrastructure and service improvements. In developing countries they are generally ignored in transport project appraisals, notwithstanding their importance. One of the reasons for ignoring these benefits in the developing countries is that there is insufficient empirical evidence to support the conventional models for valuing travel time where work patterns, particularly of the poor, are diverse and it is difficult to distinguish between work and non-work activities. The exclusion of time saving benefits may lead to a bias against investment decisions that benefit the poor and understate the poverty reduction potential of transport investments in Least Developed Countries (LDCs). This is because the poor undertake most travel and transport by walking and headloading on local roads, tracks and paths and improvements of local infrastructure and services bring large time saving benefits for them through modal shifts. The paper reports on an empirical study to develop a methodology for valuing rural travel time savings in the LDCs. Apart from identifying the theoretical and empirical issues in valuing travel time savings in the LDCs, the paper presents and discusses the results of an analysis of data from Bangladesh. Some of the study findings challenge the conventional wisdom concerning the time saving values. The Bangladesh study suggests that the western concept of dividing travel time savings into working and non-working time savings is broadly valid in the developing country context. The study validates the use of preference methods in valuing non-working time saving values. However, stated preference (SP) method is more appropriate than revealed preference (RP) method.

Individual spirit at work and its relationship with employee work attitudes and organisational outcomes:An empirical examination in corporate Thailand

The purpose of this thesis is to conduct empirical research in corporate Thailand in order to (1) validate the Spirit at Work Scale (2) investigate the relationships between individual spirit at work and three employee work attitudinal variables (job satisfaction, organisational identification and psychological well-being) and three organisational outcomes (in-role performance, organisational citizenship behaviours (OCB), and turnover intentions) (3) further examine causal relations among these organisational behaviour variables with a longitudinal design (4) examine three employee work attitudes as mediator variables between individual spirit at work and three organisational outcomes and (5) explore the potential antecedents of organisational conditions that foster employee experienced individual spirit at work. The two pilot studies with 155 UK and 175, 715 Thai samples were conducted for validation testing of the main measure used in this study: Spirit at Work Scale (Kinjerski & Skrypnek, 2006a). The results of the two studies including discriminant validity analyses strongly provided supportive evidence that Spirit at Work Scale (SAWS) is a sound psychometric measure and also a distinct construct from the three work attitude constructs. The final model of SAWS contains a total of twelve items; a three factor structure (meaning in work, sense of community, and spiritual connection) in which the sub-factors loaded on higher order factors and also had very acceptable reliability. In line with these results it was decided to use the second-order of SAWS model for Thai samples in the main study and subsequent analysis. The 715 completed questionnaires were received from the first wave of data collection during July - August 2008 and the second wave was conducted again within the same organisations and 501 completed questionnaires were received during March - April 2009. Data were obtained through 49 organisations which were from three types of organisations within Thailand: public organisations, for-profit organisations, and notfor-profit organisations. Confirmatory factor analysis of all measures used in the study and hypothesised model were tested with structural equation modelling techniques. The results were greatly supportive for the direct structural model and partially supportive for the fully mediated model. Moreover, there were different findings across self report and supervisor rating on performance and OCB models. Additionally, the antecedent conditions that fostered employees experienced individual spirit at work and the implications of these findings for research and practice are discussed.

Variations of local heat transfer coefficient in piped flow of viscous liquids

Measurements were carried out to determine local coefficients of heat transfer in short lengths of horizontal pipe, and in the region of an discontinuity in pipe diameter. Laminar, transitional and turbulent flow regimes were investigated, and mixtures of propylene glycol and water were used in the experiments to give a range of viscous fluids. Theoretical and empirical analyses were implemented to find how the fundamental mechanism of forced convection was modified by the secondary effects of free convection, temperature dependent viscosity, and viscous dissipation. From experiments with the short tube it was possible to determine simple empirical relationships describing the axial distribution of the local 1usselt number and its dependence on the Reynolds and Prandtl numbers. Small corrections were made to account for the secondary effects mentioned above. Two different entrance configurations were investigated to demonstrate how conditions upstream could influence the heat transfer coefficients measured downstream In experiments with a sudden contraction in pipe diameter the distribution of local 1u3se1t number depended on the Prandtl number of the fluid in a complicated way. Graphical data is presented describing this dependence for a range of fluids indicating how the local Nusselt number varied with the diameter-ratio. Ratios up to 3.34:1 were considered. With a sudden divergence in pipe diameter, it was possible to derive the axial distribution of the local Nusse1t number for a range of Reynolds and Prandtl numbers in a similar way to the convergence experiments. Difficulty was encountered in explaining some of the measurements obtained at low Reynolds numbers, and flow visualization techniques wore used to determine the complex flow patterns which could lead to the anomalous results mentioned. Tests were carried out with divergences up to 1:3.34 to find the way in which the local Nusselt number varied with the diameter ratio, and a few experiments were carried out with very large ratios up .to 14.4. A limited amount of theoretical analysis of the 'divergence' system was carried out to substantiate certain explanations of the heat transfer mechanisms postulated.

Flow patterns and performance of distillation trays

It is known that distillation tray efficiency depends on the liquid flow pattern, particularly for large diameter trays. Scale·up failures due to liquid channelling have occurred, and it is known that fitting flow control devices to trays sometirr.es improves tray efficiency. Several theoretical models which explain these observations have been published. Further progress in understanding is at present blocked by lack of experimental measurements of the pattern of liquid concentration over the tray. Flow pattern effects are expected to be significant only on commercial size trays of a large diameter and the lack of data is a result of the costs, risks and difficulty of making these measurements on full scale production columns. This work presents a new experiment which simulates distillation by water cooling. and provides a means of testing commercial size trays in the laboratory. Hot water is fed on to the tray and cooled by air forced through the perforations. The analogy between heat and mass transfer shows that the water temperature at any point is analogous to liquid concentration and the enthalpy of the air is analogous to vapour concentration. The effect of the liquid flow pattern on mass transfer is revealed by the temperature field on the tray. The experiment was implemented and evaluated in a column of 1.2 m. dia. The water temperatures were measured by thennocouples interfaced to an electronic computerised data logging system. The "best surface" through the experimental temperature measurements was obtained by the mathematical technique of B. splines, and presented in tenos of lines of constant temperature. The results revealed that in general liquid channelling is more imponant in the bubbly "mixed" regime than in the spray regime. However, it was observed that severe channelling also occurred for intense spray at incipient flood conditions. This is an unexpected result. A computer program was written to calculate point efficiency as well as tray efficiency, and the results were compared with distillation efficiencies for similar loadings. The theoretical model of Porter and Lockett for predicting distillation was modified to predict water cooling and the theoretical predictions were shown to be similar to the experimental temperature profiles. A comparison of the repeatability of the experiments with an errors analysis revealed that accurate tray efficiency measurements require temperature measurements to better than ± 0.1 °c which is achievable with conventional techniques. This was not achieved in this work, and resulted in considerable scatter in the efficiency results. Nevertheless it is concluded that the new experiment is a valuable tool for investigating the effect of the liquid flow pattern on tray mass transfer.

Has DRG payment influenced the technical efficiency and productivity of diagnostic technologies in Portuguese public hospitals? An empirical analysis using parametric and non‐parametric methods

The use of Diagnosis Related Groups (DRG) as a mechanism for hospital financing is a currently debated topic in Portugal. The DRG system was scheduled to be initiated by the Health Ministry of Portugal on January 1, 1990 as an instrument for the allocation of public hospital budgets funded by the National Health Service (NHS), and as a method of payment for other third party payers (e.g., Public Employees (ADSE), private insurers, etc.). Based on experience from other countries such as the United States, it was expected that implementation of this system would result in more efficient hospital resource utilisation and a more equitable distribution of hospital budgets. However, in order to minimise the potentially adverse financial impact on hospitals, the Portuguese Health Ministry decided to gradually phase in the use of the DRG system for budget allocation by using blended hospitalspecific and national DRG casemix rates. Since implementation in 1990, the percentage of each hospitals budget based on hospital specific costs was to decrease, while the percentage based on DRG casemix was to increase. This was scheduled to continue until 1995 when the plan called for allocating yearly budgets on a 50% national and 50% hospitalspecific cost basis. While all other nonNHS third party payers are currently paying based on DRGs, the adoption of DRG casemix as a National Health Service budget setting tool has been slower than anticipated. There is now some argument in both the political and academic communities as to the appropriateness of DRGs as a budget setting criterion as well as to their impact on hospital efficiency in Portugal. This paper uses a twostage procedure to assess the impact of actual DRG payment on the productivity (through its components, i.e., technological change and technical efficiency change) of diagnostic technology in Portuguese hospitals during the years 1992–1994, using both parametric and nonparametric frontier models. We find evidence that the DRG payment system does appear to have had a positive impact on productivity and technical efficiency of some commonly employed diagnostic technologies in Portugal during this time span.

Experimental investigation and CFD simulation of insulation debris transport phenomena in water flow

The investigation of insulation debris generation, transport and sedimentation becomes important with regard to reactor safety research for PWR and BWR, when considering the long-term behavior of emergency core cooling systems during all types of loss of coolant accidents (LOCA). The insulation debris released near the break during a LOCA incident consists of a mixture of disparate particle population that varies with size, shape, consistency and other properties. Some fractions of the released insulation debris can be transported into the reactor sump, where it may perturb/impinge on the emergency core cooling systems. Open questions of generic interest are the sedimentation of the insulation debris in a water pool, its possible re-suspension and transport in the sump water flow and the particle load on strainers and corresponding pressure drop. A joint research project on such questions is being performed in cooperation between the University of Applied Sciences Zittau/Görlitz and the Forschungszentrum Dresden-Rossendorf. The project deals with the experimental investigation of particle transport phenomena in coolant flow and the development of CFD models for its description. While the experiments are performed at the University at Zittau/Görlitz, the theoretical modeling efforts are concentrated at Forschungszentrum Dresden-Rossendorf. In the presentation the basic concepts for CFD modeling are described and feasibility studies including the conceptual design of the experiments are presented.