Apparatus and test methods for measuring the impact of golf balls on turf and their application in the field

An apparatus was developed to project spinning golf balls directly onto golf greens. This employed a modified baseball/practice machine with two counter-rotating pneumatic wheels. The speed of the wheels could be varied independently allowing backspin to be given to the ball. The ball was projected into a darkened enclosure where the motion of the ball before and after impacting with the turf was recorded using a still camera and a stroboscope. The resulting photographs contained successive images of the ball on a single frame of film. The apparatus was tested on eighteen golf courses resulting in 721 photographs of impacts. Statistical analysis was carried out on the results of the photographs and from this, two types of green emerged. On the first, the ball tended to rebound with topspin, while on the second, the ball retained backspin after impact if the initial backspin was greater than about 350 rads-1. Eleven tests were devised to determine the characteristics of greens and statistical techniques were used to analyse the relationships between these tests. These showed the effects of the green characteristics on ball/turf impacts. It was found that the ball retained backspin on greens that were freely drained and had less than 60% of Poa annua (annual meadow grass) in their swards. Visco-elastic models were used to simulate the impact of the ball with the turf. Impacts were simulated by considering the ball to be rigid and the turf to be a two layered system consisting of springs and dampers. The model showed good agreement with experiment and was used to simulate impacts from two different shots onto two contrasting types of green.

Development and evaluation of a non-destructive adhesion test

The object of this work was to further develop the idea introduced by Muaddi et al (1981) which enables some of the disadvantages of earlier destructive adhesion test methods to be overcome. The test is non-destructive in nature but it does need to be calibrated against a destructive method. Adhesion is determined by measuring the effect of plating on internal friction. This is achieved by determining the damping of vibrations of a resonating specimen before and after plating. The level of adhesion was considered by the above authors to influence the degree of damping. In the major portion of the research work the electrodeposited metal was Watt's nickel, which is ductile in nature and is therefore suitable for peel adhesion testing. The base metals chosen were aluminium alloys S1C and HE9 as it is relatively easy to produce varying levels of adhesion between the substrate and electrodeposited coating by choosing the appropriate process sequence. S1C alloy is the commercially pure aluminium and was used to produce good adhesion. HE9 aluminium alloy is a more difficult to plate alloy and was chosen to produce poorer adhesion. The "Modal Testing" method used for studying vibrations was investigated as a possible means of evaluating adhesion but was not successful and so research was concentrated on the "Q" meter. The method based on the use of a "Q" meter involves the principle of exciting vibrations in a sample, interrupting the driving signal and counting the number of oscillations of the freely decaying vibrations between two known preselected amplitudes of oscillations. It was not possible to reconstruct a working instrument using Muaddi's thesis (1982) as it had either a serious error or the information was incomplete. Hence a modified "Q" meter had to be designed and constructed but it was then difficult to resonate non-magnetic materials, such as aluminium, therefore, a comparison before and after plating could not be made. A new "Q" meter was then developed based on an Impulse Technique. A regulated miniature hammer was used to excite the test piece at the fundamental mode instead of an electronic hammer and test pieces were supported at the two predetermined nodal points using nylon threads. This instrument developed was not very successful at detecting changes due to good and poor pretreatments given before plating, however, it was more sensitive to changes at the surface such as room temperature oxidation. Statistical analysis of test results from untreated aluminium alloys show that the instrument is not always consistent, the variation was even bigger when readings were taken on different days. Although aluminium is said to form protective oxides at room temperature there was evidence that the aluminium surface changes continuously due to film formation, growth and breakdown. Nickel plated and zinc alloy immersion coated samples also showed variation in Q with time. In order to prove that the variations in Q were mainly due to surface oxidation, aluminium samples were lacquered and anodised Such treatments enveloped the active surfaces reacting with the environment and the Q variation with time was almost eliminated especially after hard anodising. This instrument detected major differences between different untreated aluminium substrates.Also Q values decreased progressively as coating thicknesses were increased. This instrument was also able to detect changes in Q due to heat-treatment of aluminium alloys.

Enhancing delivery of health behaviour change interventions in primary care: a meta-synthesis of views and experiences of primary care nurses

Objective To systematically find and synthesise qualitative studies that elicited views and experiences of nurses involved in the delivery of health behaviour change (HBC) interventions in primary care, with a focus on how this can inform enhanced delivery and adherence to a structured approach for HBC interventions. Methods Systematic search of five electronic databases and additional strategies to maximise identification of studies, appraisal of studies and use of meta-synthesis to develop an inductive and interpretative form of knowledge synthesis. Results Nine studies met the inclusion criteria. Synthesis resulted in the development of four inter-linking themes; (a) actively engaging nurses in the process of delivering HBC interventions, (b) clarifying roles and responsibilities of those involved, (c) engaging practice colleagues, (d) communication of aims and potential outcomes of the intervention. Conclusion The synthesis of qualitative evidence resulted in the development of a conceptual framework that remained true to the findings of primary studies. This framework describes factors that should be actively promoted to enhance delivery of and adherence to HBC interventions by nurses working in primary care. Practice implications The findings can be used to inform strategies for researchers, policymakers and healthcare providers to enhance fidelity and support delivery of HBC interventions.

OTDM network processing using all-optical and electro-optical devices

The current optical communications network consists of point-to-point optical transmission paths interconnected with relatively low-speed electronic switching and routing devices. As the demand for capacity increases, then higher speed electronic devices will become necessary. It is however hard to realise electronic chip-sets above 10 Gbit/s, and therefore to increase the achievable performance of the network, electro-optic and all-optic switching and routing architectures are being investigated. This thesis aims to provide a detailed experimental analysis of high-speed optical processing within an optical time division multiplexed (OTDM) network node. This includes the functions of demultiplexing, 'drop and insert' multiplexing, data regeneration, and clock recovery. It examines the possibilities of combining these tasks using a single device. Two optical switching technologies are explored. The first is an all-optical device known as 'semiconductor optical amplifier-based nonlinear optical loop mirror' (SOA-NOLM). Switching is achieved by using an intense 'control' pulse to induce a phase shift in a low-intensity signal propagating through an interferometer. Simultaneous demultiplexing, data regeneration and clock recovery are demonstrated for the first time using a single SOA-NOLM. The second device is an electroabsorption (EA) modulator, which until this thesis had been used in a uni-directional configuration to achieve picosecond pulse generation, data encoding, demultiplexing, and 'drop and insert' multiplexing. This thesis presents results on the use of an EA modulator in a novel bi-directional configuration. Two independent channels are demultiplexed from a high-speed OTDM data stream using a single device. Simultaneous demultiplexing with stable, ultra-low jitter clock recovery is demonstrated, and then used in a self-contained 40 Gbit/s 'drop and insert' node. Finally, a 10 GHz source is analysed that exploits the EA modulator bi-directionality to increase the pulse extinction ratio to a level where it could be used in an 80 Gbit/s OTDM network.

Complexity and chirality indices for molecular informatics::differential geometry approach

Novel molecular complexity measures are designed based on the quantum molecular kinematics. The Hamiltonian matrix constructed in a quasi-topological approximation describes the temporal evolution of the modelled electronic system and determined the time derivatives for the dynamic quantities. This allows to define the average quantum kinematic characteristics closely related to the curvatures of the electron paths, particularly, the torsion reflecting the chirality of the dynamic system. A special attention has been given to the computational scheme for this chirality measure. The calculations on realistic molecular systems demonstrate reasonable behaviour of the proposed molecular complexity indices.

Effect of medications with anti-cholinergic properties on cognitive function, delirium, physical function and mortality:a systematic review

Objectives: to determine the effect of drugs with anti-cholinergic properties on relevant health outcomes.Design: electronic published and unpublished literature/trial registries were systematically reviewed. Studies evaluating medications with anti-cholinergic activity on cognitive function, delirium, physical function or mortality were eligible.Results: forty-six studies including 60,944 participants were included. Seventy-seven percent of included studies evaluating cognitive function (n = 33) reported a significant decline in cognitive ability with increasing anti-cholinergic load (P < 0.05). Four of five included studies reported no association with delirium and increasing anti-cholinergic drug load (P > 0.05). Five of the eight included studies reported a decline in physical function in users of anti-cholinergics (P < 0.05). Three of nine studies evaluating mortality reported that the use of drugs with anti-cholinergic properties was associated with a trend towards increased mortality, but this was not statistically significant. The methodological quality of the evidence-base ranged from poor to very good.Conclusion: medicines with anti-cholinergic properties have a significant adverse effect on cognitive and physical function, but limited evidence exists for delirium or mortality outcomes. © The Author 2014. Published by Oxford University Press on behalf of the British Geriatrics Society. All rights reserved.

Surrogate-based analysis and optimization for the design of heat sinks with jet impingement

Heat sinks are widely used for cooling electronic devices and systems. Their thermal performance is usually determined by the material, shape, and size of the heat sink. With the assistance of computational fluid dynamics (CFD) and surrogate-based optimization, heat sinks can be designed and optimized to achieve a high level of performance. In this paper, the design and optimization of a plate-fin-type heat sink cooled by impingement jet is presented. The flow and thermal fields are simulated using the CFD simulation; the thermal resistance of the heat sink is then estimated. A Kriging surrogate model is developed to approximate the objective function (thermal resistance) as a function of design variables. Surrogate-based optimization is implemented by adaptively adding infill points based on an integrated strategy of the minimum value, the maximum mean square error approach, and the expected improvement approaches. The results show the influence of design variables on the thermal resistance and give the optimal heat sink with lowest thermal resistance for given jet impingement conditions.

UV-Inscribed optical fiber gratings in Mid-IR range and their laser applications

We have UV-inscribed fiber Bragg gratings (FBGs), long-period gratings (LPGs), and tilted fiber gratings (TFGs) into mid-IR 2μm range using three common optical fiber grating fabrication techniques (two-beam holographic, phase mask, and point-by-point). The fabricated FBGs have been evaluated for thermal and strain response. It has been revealed that the FBG devices with responses in mid-IR range are much more sensitive to temperature than that in near-IR range. To explore the unique cladding mode coupling function, we have investigated the thermal and refractive index sensitivities of LPGs and identified that the coupled cladding modes in mid-IR range are also much more sensitive to temperature and surrounding medium refractive index change. The 45° tilted fiber gratings (45°-TFGs) as polarizing devices in mid-IR have been investigated for their polarization extinction characteristics. As efficient reflection filters and in-cavity polarizers, the mid-IR FBGs and 45°-TFGs have been employed in fiber laser cavity to realize multi-wavelength 2 μm Tm-doped CW and mode locked fiber lasers, respectively.

Leadership and organisational outcomes in healthcare

This research examined to what extent and how leadership is related to organisational outcomes in healthcare. Based on the Job Demands-Resource model, a set of hypotheses was developed, which predicted that the effect of leadership on healthcare outcomes would be mediated by job design, employee engagement, work pressure, opportunity for involvement, and work-life balance. The research focused on the National Health Service (NHS) in England, and examined the relationships between senior leadership, first line supervisory leadership and outcomes. Three years of data (2008 – 2010) were gathered from four data sources: the NHS National Staff Survey, the NHS Inpatient Survey, the NHS Electronic Record, and the NHS Information Centre. The data were drawn from 390 healthcare organisations and over 285,000 staff annually for each of the three years. Parallel mediation regressions modelled both cross sectional and longitudinal designs. The findings revealed strong relationships between senior leadership and supervisor support respectively and job design, engagement, opportunity for involvement, and work-life balance, while senior leadership was also associated with work pressure. Except for job design, there were significant relationships between the mediating variables and the outcomes of patient satisfaction, employee job satisfaction, absenteeism, and turnover. Relative importance analysis showed that senior leadership accounted for significantly more variance in relationships with outcomes than supervisor support in the majority of models tested. Results are discussed in relation to theoretical and practical contributions. They suggest that leadership plays a significant role in organisational outcomes in healthcare and that previous research may have underestimated how influential senior leaders may be in relation to these outcomes. Moreover, the research suggests that leaders in healthcare may influence outcomes by the way they manage the work pressure, engagement, opportunity for involvement and work-life balance of those they lead.