Development of science and technology policy for Kuwait

The status of Science and Technology in KUWAIT has been analysed in order to assess the extent of the application of Science and Technology needed for the Country's development. The design and implementation of a Science and Technology Policy has been examined to identify the appropriate technology necessary to improve KUWAIT's socio-economic-industrial structures. Following a general and critical review of the role of Science and Technology in the developing countries, the author has reviewed the past and contemporary employment of Science and Technology for development.of various sectors and the existence, if any, of any form (explicit, implicit, or both) of a Science and Technology Policy in KUWAIT. The thesis is structured to evaluate almost all of the sectors in KUWAIT which utilise Science and/or Technology, the effectiveness of such practices, their policymaking process, the channels by which policies were transformed into sources of influence through Governmental action and the impact that various policy instruments at the disposal of the the Government had on the development of S & T capabilities. The author has studied the implications of the absence of a Science and Technology Policy in Kuwait by examining some specific case studies, eg, the absence of a Technology Assessment Process and the negative impacts resulting from this; the ad-hoc allocation of the research and development budget instead of its being based on a percentage of GNP; the limitations imposed on the development of indigenous contracting companies and consultancy and engineering design offices; the impacts of the absence of Technology Transfer Centre, and so forth. As a consequence of the implications of the above studies, together with the negative results from the absence of an explicit Science and Technology Policy, eg, research and development activities do not relate to the national development plans, the author suggests that a Science and Technology Policy-Making Body should be established to formulate, develop, monitor and correlate the Science and Technology Activities in KUWAIT.

Design and development of an agent-based information system for process improvement

To meet changing needs of customers and to survive in the increasingly globalised and competitive environment, it is necessary for companies to equip themselves with intelligent tools, thereby enabling managerial levels to use the tactical decision in a better way. However, the implementation of an intelligent system is always a challenge in Small- and Medium-sized Enterprises (SMEs). Therefore, a new and simple approach with 'process rethinking' ability is proposed to generate ongoing process improvements over time. In this paper, a roadmap of the development of an agent-based information system is described. A case example has also been provided to show how the system can assist non-specialists, for example, managers and engineers to make right decisions for a continual process improvement. Copyright © 2006 Inderscience Enterprises Ltd.

The design and evaluation of distributed virtual environment to support learning in global operations management

The primary goal of this research is to design and develop an education technology to support learning in global operations management. The research implements a series of studies to determine the right balance among user requirements, learning methods and applied technologies, on a view of student-centred learning. This research is multidisciplinary by nature, involving topics from various disciplines such as global operations management, curriculum and contemporary learning theory, and computer aided learning. Innovative learning models that emphasise on technological implementation are employed and discussed throughout this research.

From national innovation systems to national innovation capacity:internationalisation and technology transfer perspectives

The last decade or so has witnessed the emergence of the national innovation system (NIS) phenomenon. Since then, many scholars have investigated NIS and its implementation in different countries. However, there are very few investigations into the relationship between the NIS of a country and its national innovation capacity. This paper aims to make a contribution in this area by examining the link that currently exists between these two topics. Whilst examining this relationship, we also explore internationalisation and technology transfer, being cognate areas that have been investigated during the same period. This follows our assertion that the link between NIS and national innovation capacity is the mechanism of internationalisation and technology transfer. The NIS approach was introduced in the late 1980s (see Freeman, 1987; Dosi et al., 1988) and further elaborated later (see Lundvall, 1992; Nelson, 1993; Edquist, 1997). In essence, a country?s NIS is a historically grown subsystem of the entire national economy consisting of organisations and institutions which play a major role in the innovative activity in the country. In the NIS approach, interactions within organisations as well as the interplay between organisations and institutions are of central importance. The NIS approach has been used to reveal the structure of the innovation processes and the main actors involved in them in industrialised and emerging countries. Although the national focus remains strong, it has been accompanied by studies seeking to analyse the notion of systems of innovation at an international level and at a sub-national scale (Archibugi et al., 1999). Dosi in the edition of Archibugi et al. (1999) argues that the general background of the discussion of national systems is the observation of non-random distributions across countries of: corporate capabilities; organisational forms; strategies; and ultimately revealed performances, in terms of production efficiency and inputs productivities, rates of innovation, rates of adoption/diffusion of innovation themselves, dynamics of market shares on the world markets, growth of income and employment. They also mention that there are several approaches to NIS. Nelson (1993) focuses upon the specificities of national institutions and policies supporting directly or indirectly innovation, diffusion and skills accumulation. Patel and Pavitt (1991) have stressed the links between the national patterns of technological accumulation and the competencies and innovative strategies of a few major national companies. Amable et al (1997) and Soskice (1993) and Zysman (1994) focus on the specifics of national institutions including, for example, the forms of organization, financial and labour markets, training institutions, forms of state intervention in the economy etc. However, the most common reference is by Lundvall (1992) who argues that the focus on the national level is associated with the fact that national economies vary according to their production system and their institutional framework and these differences are in turn strengthened by different historical experiences, language and culture. On the other hand, the national innovation capability consists of abilities to create and carry new technological possibilities through to economic practice. The term covers a wide range of activities from capability to invent to capability to innovate and to capability to improve existing technology beyond the original design parameters (Kim, 1997). The term innovation is often associated by many with technological change at international frontiers. However, technological capability is not the same as innovation capability. Technological capability refers to assimilation, use, adaptation, and change to existing technologies. It also enables the creation of new technologies and development of new products and processes in response to changing economic environments. It denotes operational command over knowledge (Kim, 1997). It is manifested not merely by the knowledge possessed, but, more important, by the uses to which that knowledge can be put and by the proficiency with which it is applied in the activities of investment and production and in the creation of new knowledge (Westphal et al., 1985). Therefore, the analytical framework that is used in this paper is based on the way a country derives from its NIS a national innovation capacity. There are two perspectives that are identified on this way. These are internationalisation and technology transfer. Even though NIS is not directly related to national innovation capacity, to achieve national innovation capacity from NIS, the country should have the ability for technology transfer. Technology transfer is a link between these two phenomena. On the other hand, internationalisation can be either the input or the output of the relationship between NIS and national innovation capability. If a company is investing in a country because of its national innovation capacity, this can be regarded as an input to the relationship between NIS and national innovation capacity. If this company is investigating the national innovation capacity of a country then, for its internationalisation, the national innovation capacity should be important, which in turn means this company is active in innovation and innovation is also an important success factor. The interrelationship between the investment of the company and the NIS of the country (assuming that the country is competent and competitive in technology transfer) will generate and improve that country?s national innovation capacity. This is the output of internationalisation from the relationship between NIS and national innovation capacity. When companies are evaluating whether to internationalise, they investigate certain factors in the countries in which they are considering to invest. The ability to transfer technology is dependent on ability to adopt a new technology and also on the learning derived from this technology. If countries wish to attract innovation related investment they need to show their ability to have a NIS and also the capability to transfer technology. Without the technology transfer capability, the NIS is not functioning. Therefore, companies that internationalise will investigate the factors common to NIS, technology transfer, and their business needs. Through this paper we will demonstrate this link though its mechanisms. Our research will be through extensive literature review and identifying relevant aspects of previous research carried out by the authors. It will investigate certain factors of different countries that are successful in attracting innovation related foreign direct investment. Through these, we will point out the factors that are important for the link and mechanisms of NIS and national innovation capability.

Design and implementation of graphical user interfaces for complex simulations

The development of increasingly powerful computers, which has enabled the use of windowing software, has also opened the way for the computer study, via simulation, of very complex physical systems. In this study, the main issues related to the implementation of interactive simulations of complex systems are identified and discussed. Most existing simulators are closed in the sense that there is no access to the source code and, even if it were available, adaptation to interaction with other systems would require extensive code re-writing. This work aims to increase the flexibility of such software by developing a set of object-oriented simulation classes, which can be extended, by subclassing, at any level, i.e., at the problem domain, presentation or interaction levels. A strategy, which involves the use of an object-oriented framework, concurrent execution of several simulation modules, use of a networked windowing system and the re-use of existing software written in procedural languages, is proposed. A prototype tool which combines these techniques has been implemented and is presented. It allows the on-line definition of the configuration of the physical system and generates the appropriate graphical user interface. Simulation routines have been developed for the chemical recovery cycle of a paper pulp mill. The application, by creation of new classes, of the prototype to the interactive simulation of this physical system is described. Besides providing visual feedback, the resulting graphical user interface greatly simplifies the interaction with this set of simulation modules. This study shows that considerable benefits can be obtained by application of computer science concepts to the engineering domain, by helping domain experts to tailor interactive tools to suit their needs.

User interface design support for the development of knowledge-based systems

The present scarcity of operational knowledge-based systems (KBS) has been attributed, in part, to an inadequate consideration shown to user interface design during development. From a human factors perspective the problem has stemmed from an overall lack of user-centred design principles. Consequently the integration of human factors principles and techniques is seen as a necessary and important precursor to ensuring the implementation of KBS which are useful to, and usable by, the end-users for whom they are intended. Focussing upon KBS work taking place within commercial and industrial environments, this research set out to assess both the extent to which human factors support was presently being utilised within development, and the future path for human factors integration. The assessment consisted of interviews conducted with a number of commercial and industrial organisations involved in KBS development; and a set of three detailed case studies of individual KBS projects. Two of the studies were carried out within a collaborative Alvey project, involving the Interdisciplinary Higher Degrees Scheme (IHD) at the University of Aston in Birmingham, BIS Applied Systems Ltd (BIS), and the British Steel Corporation. This project, which had provided the initial basis and funding for the research, was concerned with the application of KBS to the design of commercial data processing (DP) systems. The third study stemmed from involvement on a KBS project being carried out by the Technology Division of the Trustees Saving Bank Group plc. The preliminary research highlighted poor human factors integration. In particular, there was a lack of early consideration of end-user requirements definition and user-centred evaluation. Instead concentration was given to the construction of the knowledge base and prototype evaluation with the expert(s). In response to this identified problem, a set of methods was developed that was aimed at encouraging developers to consider user interface requirements early on in a project. These methods were then applied in the two further projects, and their uptake within the overall development process was monitored. Experience from the two studies demonstrated that early consideration of user interface requirements was both feasible, and instructive for guiding future development work. In particular, it was shown a user interface prototype could be used as a basis for capturing requirements at the functional (task) level, and at the interface dialogue level. Extrapolating from this experience, a KBS life-cycle model is proposed which incorporates user interface design (and within that, user evaluation) as a largely parallel, rather than subsequent, activity to knowledge base construction. Further to this, there is a discussion of several key elements which can be seen as inhibiting the integration of human factors within KBS development. These elements stem from characteristics of present KBS development practice; from constraints within the commercial and industrial development environments; and from the state of existing human factors support.

Clinical decision support system for point of care use: ontology driven design and software implementation

OBJECTIVES: The objective of this research was to design a clinical decision support system (CDSS) that supports heterogeneous clinical decision problems and runs on multiple computing platforms. Meeting this objective required a novel design to create an extendable and easy to maintain clinical CDSS for point of care support. The proposed solution was evaluated in a proof of concept implementation. METHODS: Based on our earlier research with the design of a mobile CDSS for emergency triage we used ontology-driven design to represent essential components of a CDSS. Models of clinical decision problems were derived from the ontology and they were processed into executable applications during runtime. This allowed scaling applications' functionality to the capabilities of computing platforms. A prototype of the system was implemented using the extended client-server architecture and Web services to distribute the functions of the system and to make it operational in limited connectivity conditions. RESULTS: The proposed design provided a common framework that facilitated development of diversified clinical applications running seamlessly on a variety of computing platforms. It was prototyped for two clinical decision problems and settings (triage of acute pain in the emergency department and postoperative management of radical prostatectomy on the hospital ward) and implemented on two computing platforms-desktop and handheld computers. CONCLUSIONS: The requirement of the CDSS heterogeneity was satisfied with ontology-driven design. Processing of application models described with the help of ontological models allowed having a complex system running on multiple computing platforms with different capabilities. Finally, separation of models and runtime components contributed to improved extensibility and maintainability of the system.

A design and implementation methodology for high variety electronics assembly systems

Small indigenous manufacturers of electronic equipment are coming under increasingly severe pressure to adopt a strong defensive position against large multinational and Far Eastern companies. A common response to this threat has been for these firms to adopt a 'market driven' business strategy based on quality and customer service, rather than a 'technology led' strategy which uses technical specification and price to compete. To successfully implement this type of strategy there is a need for production systems to be redesigned to suit the new demands of marketing. Increased range and fast response require economy of scope rather t ban economy or scale while the organisation's culture must promote quality and process consciousness. This paper describes the 'Modular Assembly Cascade' concept which addresses these needs by applying the principles of flexible manufacturing (FMS) and just in time (,JlT) to electronics assembly. A methodology for executing the concept is also outlined. This is called DRAMA (Design Houtirw !'or· Adopting Modular Assembly).

Design and implementation of production systems for high variety electronics assembly

Information technology companies are having to broaden their overall strategic view in deference to the premise that it is better to be market-driven than technology-led. Cost and technical performance are no longer the only considerations, as quality and service now demand equal recognition. The production of a high volume single item has given way to that of low volume multiple items, which in turn requires some modification of production systems and brings flexible manufacturing, Just-in-Time production and total quality control into sharper focus for the achievement of corporate objectives.

Heterogeneous catalysts for clean technology:spectroscopy, design, and monitoring

Reactive, but not a reactant. Heterogeneous catalysts play an unseen role in many of today's processes and products. With the increasing emphasis on sustainability in both products and processes, this handbook is the first to combine the hot topics of heterogeneous catalysis and clean technology. It focuses on the development of heterogeneous catalysts for use in clean chemical synthesis, dealing with how modern spectroscopic techniques can aid the design of catalysts for use in liquid phase reactions, their application in industrially important chemistries - including selective oxidation, hydrogenation, solid acid- and base-catalyzed processes - as well as the role of process intensification and use of renewable resources in improving the sustainability of chemical processes. With its emphasis on applications, this book is of high interest to those working in the industry.

Design and development of logistics workflow systems for demand management with RFID

This paper discusses demand and supply chain management and examines how artificial intelligence techniques and RFID technology can enhance the responsiveness of the logistics workflow. This proposed system is expected to have a significant impact on the performance of logistics networks by virtue of its capabilities to adapt unexpected supply and demand changes in the volatile marketplace with the unique feature of responsiveness with the advanced technology, Radio Frequency Identification (RFID). Recent studies have found that RFID and artificial intelligence techniques drive the development of total solution in logistics industry. Apart from tracking the movement of the goods, RFID is able to play an important role to reflect the inventory level of various distribution areas. In today’s globalized industrial environment, the physical logistics operations and the associated flow of information are the essential elements for companies to realize an efficient logistics workflow scenario. Basically, a flexible logistics workflow, which is characterized by its fast responsiveness in dealing with customer requirements through the integration of various value chain activities, is fundamental to leverage business performance of enterprises. The significance of this research is the demonstration of the synergy of using a combination of advanced technologies to form an integrated system that helps achieve lean and agile logistics workflow.

Design and development of agent-based procurement system to enhance business intelligence

The purpose of this research is to propose a procurement system across other disciplines and retrieved information with relevant parties so as to have a better co-ordination between supply and demand sides. This paper demonstrates how to analyze the data with an agent-based procurement system (APS) to re-engineer and improve the existing procurement process. The intelligence agents take the responsibility of searching the potential suppliers, negotiation with the short-listed suppliers and evaluating the performance of suppliers based on the selection criteria with mathematical model. Manufacturing firms and trading companies spend more than half of their sales dollar in the purchase of raw material and components. Efficient data collection with high accuracy is one of the key success factors to generate quality procurement which is to purchasing right material at right quality from right suppliers. In general, the enterprises spend a significant amount of resources on data collection and storage, but too little on facilitating data analysis and sharing. To validate the feasibility of the approach, a case study on a manufacturing small and medium-sized enterprise (SME) has been conducted. APS supports the data and information analyzing technique to facilitate the decision making such that the agent can enhance the negotiation and suppler evaluation efficiency by saving time and cost.

Evaluating approaches to product design and sourcing decisions in multinational companies

Product design and sourcing decisions are among the most difficult and important of all decisions facing multinational manufacturing companies, yet associated decision support and evaluation systems tend to be myopic in nature. Design for manufacture and assembly techniques, for example, generally focuses on manufacturing capability and ignores capacity although both should be considered. Similarly, most modelling and evaluation tools available to examine the performance of various solution and improvement techniques have a narrower scope than desired. A unique collaboration, funded by the US National Science Foundation, between researchers in the USA and the UK currently addresses these problems. This paper describes a technique known as Design For the Existing Environment (DFEE) and an holistic evaluation system based on enterprise simulation that was used to demonstrate the business benefits of DFEE applied in a simple product development and manufacturing case study. A project that will extend these techniques to evaluate global product sourcing strategies is described along with the practical difficulties of building an enterprise simulation on the scale and detail required.

Design and development of a time of flight fast scattering spectrometer : a quantitative surface analysis technique and a new approach towards the experimental investigation of the surface particle interactions

A new surface analysis technique has been developed which has a number of benefits compared to conventional Low Energy Ion Scattering Spectrometry (LEISS). A major potential advantage arising from the absence of charge exchange complications is the possibility of quantification. The instrumentation that has been developed also offers the possibility of unique studies concerning the interaction between low energy ions and atoms and solid surfaces. From these studies it may also be possible, in principle, to generate sensitivity factors to quantify LEISS data. The instrumentation, which is referred to as a Time-of-Flight Fast Atom Scattering Spectrometer has been developed to investigate these conjecture in practice. The development, involved a number of modifications to an existing instrument, and allowed samples to be bombarded with a monoenergetic pulsed beam of either atoms or ions, and provided the capability to analyse the spectra of scattered atoms and ions separately. Further to this a system was designed and constructed to allow incident, exit and azimuthal angles of the particle beam to be varied independently. The key development was that of a pulsed, and mass filtered atom source; which was developed by a cyclic process of design, modelling and experimentation. Although it was possible to demonstrate the unique capabilities of the instrument, problems relating to surface contamination prevented the measurement of the neutralisation probabilities. However, these problems appear to be technical rather than scientific in nature, and could be readily resolved given the appropriate resources. Experimental spectra obtained from a number of samples demonstrate some fundamental differences between the scattered ion and neutral spectra. For practical non-ordered surfaces the ToF spectra are more complex than their LEISS counterparts. This is particularly true for helium scattering where it appears, in the absence of detailed computer simulation, that quantitative analysis is limited to ordered surfaces. Despite this limitation the ToFFASS instrument opens the way for quantitative analysis of the 'true' surface region to a wider range of surface materials.

Computer aided design and manufacture for three dimensional milling

Advances in both computer technology and the necessary mathematical models capable of capturing the geometry of arbitarily shaped objects has led to the development in this thesis of a surface generation package called 'IBSCURF' aimed at providing a more economically viable solution to free-form surface manufacture. A suit of computer programs written in FORTRAN 77 has been developed to provide computer aids for every aspect of work in designing and machining free-form surfaces. A vector-valued parametric method was used for shape description and a lofting technique employed for the construction of the surface. The development of the package 'IBSCURF' consists of two phases. The first deals with CAD. The design process commences in defining the cross-sections which are represented by uniform B-spline curves as approximations to give polygons. The order of the curve and the position and number of the polygon vertices can be used as parameters for the modification to achieve the required curves. When the definitions of the sectional curves is complete, the surface is interpolated over them by cubic cardinal splines. To use the CAD function of the package to design a mould for a plastic handle, a mathematical model was developed. To facilitate the integration of design and machining using the mathematical representation of the surface, the second phase of the package is concerned with CAM which enables the generation of tool offset positions for ball-nosed cutters and a general post-processor has been developed which automatically generates NC tape programs for any CNC milling machine. The two phases of these programs have been successfully implemented, as a CAD/CAM package for free-form surfaces on the VAX 11/750 super-minicomputer with graphics facilities for displaying drawings interactively on the terminal screen. The development of this package has been beneficial in all aspects of design and machining of free form surfaces.