Novel formulation strategies for the fabrication of lyophilised orally disintegrating tablets

Orally disintegrating Tablets (ODTs), also known as fast-disintegrating, fast-melt or fast-dissolving tablets, are a relatively novel dosage technology that involves the rapid disintegration or dissolution of the dosage form into a solution or suspension in the mouth without the need for water. The solution containing the active ingredients is swallowed, and the active ingredients are then absorbed through the gastrointestinal epithelium to reach the target and produce the desired effect. Formulation of ODTs was originally developed to address swallowing difficulties of conventional solid oral dosage forms (tablets and capsules) experienced by wide range of patient population, especially children and elderly. The current work investigates the formulation and development of ODTs prepared by freeze drying. Initial studies focused on formulation parameters that influence the manufacturing process and performance of lyophilised tablets based on excipients used in commercial products (gelatin and saccharides). The second phase of the work was followed up by comprehensive studies to address the essential need to create saccharide free ODTs using naturally accruing amino acids individually or in combinations. Furthermore, a factorial design study was carried out to investigate the feasibility of delivering multiparticulate systems of challenging drugs using a novel formulation that exploited the electrostatic associative interaction between gelatin and carrageenan. Finally, studies aimed to replace gelatin with ethically and morally accepted components to the end users were performed and the selected binder was used in factorial design studies to investigate and optimise ODT formulations that incorporated drugs with varies physicochemical properties. Our results show that formulation of elegant lyophilised ODTs with instant disintegration and adequate mechanical strength requires carful optimisation of gelatin concentration and bloom strength in addition to saccharide type and concentration. Successful formulation of saccharides free lyophilised ODTs requires amino acids that crystallise in the frozen state or display relatively high Tg', interact and integrate completely with the binder and, also, display short wetting time with the disintegrating medium. The use of an optimised mixture of gelatin, carrageenan and alanine was able to create viscous solutions to suspend multiparticulate systems and at the same time provide tablets with short disintegration times and adequate mechanical properties. On the other hand, gum arabic showed an outstanding potential for use as a binder in the formulation of lyophilised ODTs. Compared to gelatin formulations, the use of gum arabic simplified the formulation stages, shortened the freeze drying cycles and produced tablets with superior performance in terms of the disintegration time and mechanical strength. Furthermore, formulation of lyophilised ODTs based on gum arabic showed capability to deliver diverse range of drugs with advantages over commercial products.

A novel requirement for C. elegans Alix/ALX-1 in RME-1-mediated membrane transport

BACKGROUND: Alix/Bro1p family proteins have recently been identified as important components of multivesicular endosomes (MVEs) and are involved in the sorting of endocytosed integral membrane proteins, interacting with components of the ESCRT complex, the unconventional phospholipid LBPA, and other known endocytosis regulators. During infection, Alix can be co-opted by enveloped retroviruses, including HIV, providing an important function during virus budding from the plasma membrane. In addition, Alix is associated with the actin cytoskeleton and might regulate cytoskeletal dynamics. RESULTS: Here we demonstrate a novel physical interaction between the only apparent Alix/Bro1p family protein in C. elegans, ALX-1, and a key regulator of receptor recycling from endosomes to the plasma membrane, called RME-1. The analysis of alx-1 mutants indicates that ALX-1 is required for the endocytic recycling of specific basolateral cargo in the C. elegans intestine, a pathway previously defined by the analysis of rme-1 mutants. The expression of truncated human Alix in HeLa cells disrupts the recycling of major histocompatibility complex class I, a known Ehd1/RME-1-dependent transport step, suggesting the phylogenetic conservation of this function. We show that the interaction of ALX-1 with RME-1 in C. elegans, mediated by RME-1/YPSL and ALX-1/NPF motifs, is required for this recycling process. In the C. elegans intestine, ALX-1 localizes to both recycling endosomes and MVEs, but the ALX-1/RME-1 interaction appears to be dispensable for ALX-1 function in MVEs and/or late endosomes. CONCLUSIONS: This work provides the first demonstration of a requirement for an Alix/Bro1p family member in the endocytic recycling pathway in association with the recycling regulator RME-1.

Simultaneous demultiplexing and clock recovery using a single electroabsorption modulator in a novel bi-directional configuration

A single electroabsorption modulator was used to demultiplex a 10 Gbit/s channel from a 40 Gbit/s OTDM data stream, whilst simultaneously recovering the 10 GHz electrical clock. This was achieved using a new bi-directional operation of the EA modulator, combined with a simple phase-locked loop feedback circuit. Excellent system performance was achieved, indicating that operation up to and beyond 100 Gbit/s is possible using current technology.

Fibre gratings in novel optical fibres for applications in sensing

This thesis presents the fabrication of fibre gratings in novel optical fibres for sensing applications. Long period gratings have been inscribed into photonic crystal fibre using the electric-arc technique. The resulting sensing characteristics were found to depend on the air-hole geometry of the particular fibre. This provides the potential of designing a fibre to have enhanced sensitivity to a particular measure and whilst removing unwanted cross sensitivities. Fibre Bragg gratings have been fabricated in a variety of polymer optical fibres, including microstructured polymer optical fibre, using a continuous wave helium cadmium laser. The thermal response of the gratings have been characterised and found to have enhanced sensitivity compared to fibre Bragg gratings in silica optical fibre. The increased sensitivity has been harnessed to achieve a grating based device in single mode step index polymer optical fibre by fabricating an electrically tunable fibre Bragg grating. This was accomplished by coating the grating region in a thin layer of copper, which upon application of a direct current, causes a temperature induced Bragg wavelength shift.

Design, modeling and construction of a novel ablative fast pyrolysis reactor and product collection system

The objective of this work was to design, construct and commission a new ablative pyrolysis reactor and a high efficiency product collection system. The reactor was to have a nominal throughput of 10 kg/11r of dry biomass and be inherently scalable up to an industrial scale application of 10 tones/hr. The whole process consists of a bladed ablative pyrolysis reactor, two high efficiency cyclones for char removal and a disk and doughnut quench column combined with a wet walled electrostatic precipitator, which is directly mounted on top, for liquids collection. In order to aid design and scale-up calculations, detailed mathematical modelling was undertaken of the reaction system enabling sizes, efficiencies and operating conditions to be determined. Specifically, a modular approach was taken due to the iterative nature of some of the design methodologies, with the output from one module being the input to the next. Separate modules were developed for the determination of the biomass ablation rate, specification of the reactor capacity, cyclone design, quench column design and electrostatic precipitator design. These models enabled a rigorous design protocol to be developed capable of specifying the required reactor and product collection system size for specified biomass throughputs, operating conditions and collection efficiencies. The reactor proved capable of generating an ablation rate of 0.63 mm/s for pine wood at a temperature of 525 'DC with a relative velocity between the heated surface and reacting biomass particle of 12.1 m/s. The reactor achieved a maximum throughput of 2.3 kg/hr, which was the maximum the biomass feeder could supply. The reactor is capable of being operated at a far higher throughput but this would require a new feeder and drive motor to be purchased. Modelling showed that the reactor is capable of achieving a reactor throughput of approximately 30 kg/hr. This is an area that should be considered for the future as the reactor is currently operating well below its theoretical maximum. Calculations show that the current product collection system could operate efficiently up to a maximum feed rate of 10 kg/Fir, provided the inert gas supply was adjusted accordingly to keep the vapour residence time in the electrostatic precipitator above one second. Operation above 10 kg/hr would require some modifications to the product collection system. Eight experimental runs were documented and considered successful, more were attempted but due to equipment failure had to be abandoned. This does not detract from the fact that the reactor and product collection system design was extremely efficient. The maximum total liquid yield was 64.9 % liquid yields on a dry wood fed basis. It is considered that the liquid yield would have been higher had there been sufficient development time to overcome certain operational difficulties and if longer operating runs had been attempted to offset product losses occurring due to the difficulties in collecting all available product from a large scale collection unit. The liquids collection system was highly efficient and modeling determined a liquid collection efficiency of above 99% on a mass basis. This was validated due to the fact that a dry ice/acetone condenser and a cotton wool filter downstream of the collection unit enabled mass measurements of the amount of condensable product exiting the product collection unit. This showed that the collection efficiency was in excess of 99% on a mass basis.

A novel entropy measure for analysis of the electrocardiogram

There has been much recent research into extracting useful diagnostic features from the electrocardiogram with numerous studies claiming impressive results. However, the robustness and consistency of the methods employed in these studies is rarely, if ever, mentioned. Hence, we propose two new methods; a biologically motivated time series derived from consecutive P-wave durations, and a mathematically motivated regularity measure. We investigate the robustness of these two methods when compared with current corresponding methods. We find that the new time series performs admirably as a compliment to the current method and the new regularity measure consistently outperforms the current measure in numerous tests on real and synthetic data.

Effect of pulsed current on the electrodeposition of chromium and copper

This research was concerned with the effects of pulsed current on the electrodeposition of chromium and copper. In the case of the latter metal, a novel application has been studied and a theory proposed for the ability to improve throwing power by the joint use of organic additives and pulsed reverse current. During the course of the research, several improvements were made to the pulse plating unit.Chromium. A study was made of the effect of square wave pulsed current on various physical properties of deposits from three hard chromium plating electrolytes. The effect of varying frequency at a duty cycle of 50% on the mean bulk internal stress, visual appearance, hardness, crack characteristics and surface topography of the electrodeposits was determined. X-ray diffraction techniques were used to study the phases present in the deposits. The effect of varying frequency on the cathodic efficiencies of the electrolytes was also determined. It was found that pulsed current reduced the internal stress of deposits from the sulphate catalysed electrolyte. It also reduced or eliminated cracking of deposits and reduced deposit brightness. Under certain conditions, pulsed current was found to induce the co-deposition of hydrides of chromium. Deposit hardness was found to be reduced by the use of pulsed current. Cathodic efficiencies of the high efficiency electrolytes were reduced by use of pulsed current although this effect was minimised at high frequencies. The sulphate catalysed electrolyte showed an increase in efficiency over the frequency range where hydrides were co-deposited.Copper. The polarisation behaviour of acid copper solutions containing polyethers, sulphopropyl sulphides and chloride ions was studied using both direct and pulse reverse current. The effect of these additives on the rest potentials of copper deposits immersed in the electrolyte was also studied. Hole Throwing Power on printed circuit boards was determined using a specially designed test cell. The effect of pulsed reverse current on the hole throwing power of commercially produced printed circuit boards was also studied. Polyethers were found to have an inhibiting effect on the deposition of copper whereas the sulphopropyl sulphides produced a stimulating (i.e. depolarising) effect. Studies of rest potentials made when both additives were present indicated that the sulphopropyl sulphide was preferentially adsorbed. The use of pulsed reverse current in solutions containing both polyether and sulphopropyl sulphide was found to cause desorption of the sulphopropyl sulphide at the cathode surface. Thus, at higher current densities, the inhibiting effect of the polyether produced an increase in the cathodic polarisation potential. At lower current densities, the depolarisation effect of the sulphopropyl sulphide could still occur. On printed circuit boards, this effect was found to produce an increase in the `hole throwing power' due to depolarisation of the holes relative to the surface of the boards. Typically, using direct current, hole/surface thickness ratios of 40% were obtained when plating 0.6 mm holes in a 3.2 mm thick board at a current density of 3 A/dm2 whereas using pulsed reverse current, ratios of 80% could be obtained at an equivalent rate of deposition. This was observed both in laboratory tests and on commercially plated boards.

The design of novel antifolates against pneumocystis carinii

The pneumonia caused by Pneumocystis carinii is ultimately responsible for the death of many acquired immunodeficiency syndrome (AIDS) patients. Large doses of trimethoprim and pyrimethamine in combination with a sulphonamide and/or pentamidine suppress the infection but produce serious side-effects and seldom prevent recurrence after treatment withdrawal. However, the partial success of the aforementioned antifolates, and also trimetrexate used alone, does suggest dihydrofolate reductase (DHFR) as a target for the development of antipneumocystis agents. From the DHFR inhibitory activities of 3'-substituted pyrimethamine analogues it was suggested that the 3'-(3'',3''-dimethyltriazen-1''-yl) substituent may be responsible for the greater activity for the P.carinii over the mammalian enzyme. Crystallographic and molecular modeling studies revealed considerable geometrical and electronic differences between the triazene and the chemically related formamidine functions that may account for the differences in DHFR inhibitory profiles. Structural and electronic parameters calculated for a series of 3'-(3'',3''-disubstitutedtriazen-1''-yl) pyrimethamine analogues did not correlate with the DHFR inhibitory activities. However, the in vitro screening against P.carinii DHFR revealed that the 3''-hydroxyethyl-3''-benzyl analogue was the most active and selective. Models of the active sites of human and P.carinii DHFRs were constructed using DHFR sequence and structural homology data which had identified key residues involved in substrate and cofactor binding. Low energy conformations of the 3'',3''-dimethyl and 3''-hydroxyethyl-3''-benzyle analogues, determined from nuclear magnetic resonance studies and theoretical calculations, were docked by superimposing the diaminopyrimidine fragment onto a previously docked pyrimethamine analogue. Enzyme kinetic data supported the 3''-hydroxyethyl-3''-benzyl moiety being located in the NADPH binding groove. The 3''-benzyl substituent was able to locate to within 3 AA of a valine residue in the active site of P.carinii DHFR thereby producing a hydrophobic contact. The equivalent residue in human DHFR is threonine, more hydrophilic and less likely to be involved in such a contact. This difference may account for the greater inhibitory activity this analogue has for P.carinii DHFR and provide a basis for future drug design. From an in vivo model of PCP in immunosuppressed rats it was established that the 3"-hydroxyethyl-3"-benzyl analogue was able to reduce the.P.carinii burden more effectively with increasing doses, without causmg any visible signs of toxicity. However, equivalent doses were not as effective as pentamidine, a current treatment of choice for Pneumocystis carinii pneumonia.

A novel binaural pitch elicited by phase-modulated noise:MEG and psychophysical observations

Binaural pitches are auditory percepts that emerge from combined inputs to the ears but that cannot be heard if the stimulus is presented to either ear alone. Here, we describe a binaural pitch that is not easily accommodated within current models of binaural processing. Convergent magnetoencephalography (MEG) and psychophysical measurements were used to characterize the pitch, heard when band-limited noise had a rapidly changing interaural phase difference. Several interesting features emerged: First, the pitch was perceptually lateralized, in agreement with the lateralization of the evoked changes in MEG spectral power, and its salience depended on dichotic binaural presentation. Second, the frequency of the pure tone that matched the binaural pitch lay within a lower spectral sideband of the phase-modulated noise and followed the frequency of that sideband when the modulation frequency or center frequency and bandwidth of the noise changed. Thus, the binaural pitch depended on the processing of binaural information in that lower sideband.

A novel multilocus sequence typing scheme for the opportunistic pathogen Propionibacterium acnes and characterisation of type 1 cell surface-associated antigens

We have developed a novel multilocus sequence typing (MLST) scheme and database (http://pubmlst.org/pacnes/) for Propionibacterium acnes based on the analysis of seven core housekeeping genes. The scheme, which was validated against previously described antibody, single locus and random amplification of polymorphic DNA typing methods, displayed excellent resolution and differentiated 123 isolates into 37 sequence types (STs). An overall clonal population structure was detected with six eBURST groups representing the major clades I, II and III, along with two singletons. Two highly successful and global clonal lineages, ST6 (type IA) and ST10 (type IB1), representing 64?% of this current MLST isolate collection were identified. The ST6 clone and closely related single locus variants, which comprise a large clonal complex CC6, dominated isolates from patients with acne, and were also significantly associated with ophthalmic infections. Our data therefore support an association between acne and P. acnes strains from the type IA cluster and highlight the role of a widely disseminated clonal genotype in this condition. Characterization of type I cell surface-associated antigens that are not detected in ST10 or strains of type II and III identified two dermatan-sulphate-binding proteins with putative phase/antigenic variation signatures. We propose that the expression of these proteins by type IA organisms contributes to their role in the pathophysiology of acne and helps explain the recurrent nature of the disease. The MLST scheme and database described in this study should provide a valuable platform for future epidemiological and evolutionary studies of P. acnes.

Ophthalmic engineering:the development of novel instrumentation to further research in the field

The principle theme of this thesis is the advancement and expansion of ophthalmic research via the collaboration between professional Engineers and professional Optometrists. The aim has been to develop new and novel approaches and solutions to contemporary problems in the field. The work is sub divided into three areas of investigation; 1) High technology systems, 2) Modification of current systems to increase functionality, and 3) Development of smaller more portable and cost effective systems. High Technology Systems: A novel high speed Optical Coherence Tomography (OCT) system with integrated simultaneous high speed photography was developed achieving better operational speed than is currently available commercially. The mechanical design of the system featured a novel 8 axis alignment system. A full set of capture, analysis, and post processing software was developed providing custom analysis systems for ophthalmic OCT imaging, expanding the current capabilities of the technology. A large clinical trial was undertaken to test the dynamics of contact lens edge interaction with the cornea in-vivo. The interaction between lens edge design, lens base curvature, post insertion times and edge positions was investigated. A novel method for correction of optical distortion when assessing lens indentation was also demonstrated. Modification of Current Systems: A commercial autorefractor, the WAM-5500, was modified with the addition of extra hardware and a custom software and firmware solution to produce a system that was capable of measuring dynamic accommodative response to various stimuli in real time. A novel software package to control the data capture process was developed allowing real time monitoring of data by the practitioner, adding considerable functionality of the instrument further to the standard system. The device was used to assess the accommodative response differences between subjects who had worn UV blocking contact lens for 5 years, verses a control group that had not worn UV blocking lenses. While the standard static measurement of accommodation showed no differences between the two groups, it was determined that the UV blocking group did show better accommodative rise and fall times (faster), thus demonstrating the benefits of the modification of this commercially available instrumentation. Portable and Cost effective Systems: A new instrument was developed to expand the capability of the now defunct Keeler Tearscope. A device was developed that provided a similar capability in allowing observation of the reflected mires from the tear film surface, but with the added advantage of being able to record the observations. The device was tested comparatively with the tearscope and other tear film break-up techniques, demonstrating its potential. In Conclusion: This work has successfully demonstrated the advantages of interdisciplinary research between engineering and ophthalmic research has provided new and novel instrumented solutions as well as having added to the sum of scientific understanding in the ophthalmic field.

Investigation of formulation and process of lyophilised orally disintegrating tablet (ODT) using novel amino acid combination

Lyophilised orally disintegrating tablets (ODTs) have achieved a great success in overcoming dysphagia associated with conventional solid dosage forms. However, the extensive use of saccharides within the formulation limits their use in treatment of chronic illnesses. The current study demonstrates the feasibility of using combination of proline and serine to formulate zero sacharide ODTs and investigates the effect of freezing protocol on sublimation rate and tablets characteristics. The results showed that inclusion of proline and serine improved ODT properties when compared to individual counterparts. Additionally, annealing the ODTs facilitated the sublimation process and shortened the disintegration time. © 2010 by the authors; licensee Molecular Diversity Preservation International, Basel, Switzerland.

Simultaneous demultiplexing and clock recovery using a single electroabsorption modulator in a novel bi-directional configuration

A single electroabsorption modulator was used to demultiplex a 10 Gbit/s channel from a 40 Gbit/s OTDM data stream, whilst simultaneously recovering the 10 GHz electrical clock. This was achieved using a new bi-directional operation of the EA modulator, combined with a simple phase-locked loop feedback circuit. Excellent system performance was achieved, indicating that operation up to and beyond 100 Gbit/s is possible using current technology.

The development of a novel Bio-MEMS filtration chip for the separation of specific cells in fluid suspension

In the clinical/microbiological laboratory there are currently several ways of separating specific cells from a fluid suspension. Conventionally cells can be separated based on size, density, electrical charge, light-scattering properties, and antigenic surface properties. Separating cells using these parameters can require complex technologies and specialist equipment. This paper proposes new Bio-MEMS (microelectromechanical systems) filtration chips manufactured using deep reactive ion etching (DRIE) technology that, when used in conjunction with an optical microscope and a syringe, can filter and grade cells for size without the requirement for additional expensive equipment. These chips also offer great versatility in terms of design and their low cost allows them to be disposable, eliminating sample contamination. The pumping mechanism, unlike many other current filtration techniques, leaves samples mechanically and chemically undamaged. In this paper the principles behind harnessing passive pumping are explored, modelled, and validated against empirical data, and their integration into a microfluidic device to separate cells from a mixed population suspension is described. The design, means of manufacture, and results from preliminary tests are also presented. © IMechE 2007.

A novel concentration dependent amino acid ion pair strategy to mediate drug permeation using indomethacin as a model insoluble drug

Assessment of oral drug bioavailability is an important parameter for new chemical entities (NCEs) in drug development cycle. After evaluating the pharmacological response of these new molecules, the following critical stage is to investigate their in vitro permeability. Despite the great success achieved by prodrugs, covalent linking the drug molecule with a hydrophobic moiety might result in a new entity that might be toxic or ineffective. Therefore, an alternative that would improve the drug uptake without affecting the efficacy of the drug molecule would be advantageous. The aim of the current study is to investigate the effect of ion-pairing on the permeability profile of a model drug: indomethacin (IND) to understand the mechanism behind the permeability improvement across Caco-2 monolayers. Arginine and lysine formed ion-pairs with IND at various molar ratios 1:1, 1:2, 1:4 and 1:8 as reflected by the double reciprocal graphs. The partitioning capacities of the IND were evaluated using octanol/water partitioning studies and the apparent permeabilities (P app) were measured across Caco-2 monolayers for the different formulations. Partitioning studies reflected the high hydrophobicity of IND (Log P = 3) which dropped upon increasing the concentrations of arginine/lysine in the ion pairs. Nevertheless, the prepared ion pairs improved IND permeability especially after 60 min of the start of the experiment. Coupling partitioning and permeability results suggest a decrease in the passive transcellular uptake due to the drop in IND portioning capacities and a possible involvement of active carriers. Future work will investigate which transport gene might be involved in the absorption of the ion paired formulations using molecular biology technologies. © 2014 Elsevier B.V. All rights reserved.