The steam reforming of hydrocarbons with special reference to methane

From an examination of the literature relating to the catalytic steam reforming of hydrocarbons, it is concluded that the kinetics of high pressure reforming, particularly steam-methane reforming, has received relatively little attention. Therefore because of the increasing availability of natural gas in the U.K., this system was considered worthy of investigation. An examination of the thermodynamics relating to the equilibria of steam-hydrocarbon reforming is described. The reactions most likely to have influence over the process are established and from these a computer program was written to calculate equilibrium compositions. A means of presenting such data in a graphica1 form for ranges of the operating variables is given, and also an operating chart which may be used to quickly check feed ratios employed on a working naphtha reforming plant is presented. For the experimental kinetic study of the steam-methane system, cylindrical pellets of ICI 46-1 nickel catalyst were used in the form of a rod catalyst. The reactor was of the integral type and a description is given with the operating procedures and analytical method used. The experimental work was divided into two parts, qualitative and quantitative. In the qualitative study the various reaction steps are examined in order to establish which one is rate controlling. It is concluded that the effects of film diffusion resistance within the conditions employed are negligible. In the quantitative study it was found that at 250 psig and 6500C the steam-methane reaction is much slower than the CO shift reaction and is rate controlling. Two rate mechanisms and accompanying kinetic rate equations are derived, both of which represent 'chemical' steps in the reaction and are considered of equal merit. However the possibility of a dual control involving 'chemical' and pore diffusion resistances is also expressed.

Ecological studies on high-rate biological filters with special reference to microbial biosynthesis and nitrification

Pilot scale studies of high rate filtration were initiated to assess its potential as either a primary 'roughing' filter to alleviate the seasonal overloading of low rate filters on Hereford sewage treatment works - caused by wastes from cider production - or as a two stage high rate process to provide complete sewage treatment. Four mineral and four plastic primary filter media and two plastic secondary filter media were studied. The hydraulic loading applied to the primary plastic media (11.2 m3 /m3 .d) was twice that applied to the mineral media. The plastic media removed an average around 66 percent and the mineral media around 73 percent of the BOD applied when the 90 percentile BOD concentration was 563 mg/1. At a hydraulic loading of 4 m3 /m3 .d the secondary filters removed most of the POD from partially settled primary filter effluents, with one secondary effluent satisfying a 25 mg/1 BOD and 30 mg/1 SS standard. No significant degree of nitrification was achieved. Fungi dominated the biological film of the primary filters, with invertebrate grazers having little influence on film levels. Ponding did not arise, and modular media supported lower film levels than random-fill types. Secondary filter film levels were low, being dominated by bacteria. The biological loading applied to the filters was related to sludge dewaterability, with the most readily conditionable sludges produced by filters supporting heavy film. Sludges produced by random-fill media could be dewatered as readily as those produced by low rate filters treating the same sewage. Laboratory scale studies showed a relationship between log effluent BOD and nitrification achieved by biological filters. This relationship and the relationship between BOD load applied and removed observed in all filter media could he used to optimise operating conditions required in biological filters to achieve given effluent BOD and ammoniacal nitrogen standards.

The single-phase induction motor:a critical appraisal of the rotating-field and cross-field theories with particular reference to skin effect

The purpose of this thesis is twofold: to examine the validity of the rotating-field and cross-field theories of the single-phase induction motor when applied to a cage rotor machine; and to examine the extent to which skin effect is likely to modify the characteristics of a cage rotor machine. A mathematical analysis is presented for a single-phase induction motor in which the rotor parameters are modified by skin effect. Although this is based on the usual type of ideal machine, a new form of model rotor allows approximations for skin effect phenomena to be included as an integral part of the analysis. Performance equations appropriate to the rotating-field and cross-field theories are deduced, and the corresponding explanations for the steady-state mode of operation are critically examined. The evaluation of the winding currents and developed torque is simplified by the introduction of new dimensionless factors which are functions of the resistance/reactance ratios of the rotor and the speed. Tables of the factors are included for selected numerical values of the parameter ratios, and these are used to deduce typical operating characteristics for both cage and wound rotor machines. It is shown that a qualitative explanation of the mode of operation of a cage rotor machine is obtained from either theory; but the operating characteristics must be deduced from the performance equations of the rotating-field theory, because of the restrictions on the values of the rotor parameters imposed by skin effect.

Enterprise management and ERP development:case study of Zoomlion using dynamic enterprise reference grid

The enterprise management approach provides a holistic view of organizations and their related information systems. In order to cope with the globalization, virtualization, and volatile competitive environment, traditional firms are seeking to reconstruct their organizational structures and establish new IS architectures to transform from single autonomous entities into more open enterprises supported by new Enterprise Resource Planning (ERP) systems. This paper reports on ERP engage-abilities within three different enterprise management patterns based on the theoretical foundations of the "Dynamic Enterprise Reference Grid". An exploratory inductive study in Zoomlion using the narrative research approach has been conducted. Also, this research delivers a conceptual framework to demonstrate the adoption of ERP in the three enterprise management structures and points to a new architectural type (ERPIII) for operating in the virtual enterprise paradigm. © 2010 Springer-Verlag.