The spalling of concrete in fires

The occurrence of spalling is a major factor in determining the fire resistance of concrete constructions. The apparently random occurrence of spalling has limited the development and application of fire resistance modelling for concrete structures. This Thesis describes an experimental investigation into the spalling of concrete on exposure to elevated temperatures. It has been shown that spalling may be categorised into four distinct types, aggregate spalling, corner spalling, surface spalling and explosive spalling. Aggregate spalling has been found to be a form of shear failure of aggregates local to the heated surface. The susceptibility of any particular concrete to aggregate spalling can be quantified from parameters which include the coefficients of thermal expansion of both the aggregate and the surrounding mortar, the size and thermal diffusivity of the aggregate and the rate of heating. Corner spalling, which is particularly significant for the fire resistance of concrete columns, is a result of concrete losing its tensile strength at elevated temperatures. Surface spalling is the result of excessive pore pressures within heated concrete. An empirical model has been developed to allow quantification of the pore pressures and a material failure model proposed. The dominant parameters are rate of heating, pore saturation and concrete permeability. Surface spalling may be alleviated by limiting pore pressure development and a number of methods to this end have been evaluated. Explosive spalling involves the catastrophic failure of a concrete element and may be caused by either of two distinct mechanisms. In the first instance, excessive pore pressures can cause explosive spalling, although the effect is limited principally to unloaded or relatively small specimens. A second cause of explosive spalling is where the superimposition of thermally induced stresses on applied load stresses exceed the concrete's strength.

Ultrasonic inspection of austenitic stainless steel weldments

Ultrasonic waves interact in a complex manner with the metallurgical structure of austenitic weldments resulting in ambiguity when interpreting reflections and at times in misinterpretation of defect positions. In this work, current knowledge of the structure of austenitic welds is outlined, and the influence of this structure on the propagation of ultrasonic waves is reviewed. Using an established and highly accurate technique, data on velocity variations as a function of the angle between the direction of soundwave propagation and the axes of preferred grain orientation existing in such welds, are experimentally obtained. These results and existing theory are used to provide quantitative evidence of (i) anisotropy factors in austenitic welds, (ii) beam skewing effects for different wave modes and polarizations, and (iii) the extent of acoustic impedance mismatch between parent and weld metals. The existence of "false" indications is demonstrated, and suggestions are made into their nature. The effectiveness of conventional transverse wave techniques for inspecting artificial and real defects existing in austenitic weldments is experimentally investigated, the limitations are demonstrated, and possible solutions are proposed. The possibilities offered by the use of longitudinal angle probes for ultrasonic inspection of real and artificial defects existing in austenitic weldments are experimentally investigated, and parameters such as probe angle, frequency and scanning position are evaluated. Detailed work has been carried out on the interaction of ultrasound with fatigue and corrosion-fatigue cracks in the weld metal and the heat affected zones (HAZs) of 316 and 347 types of austenitic weldments, together with the influence of elastic compressive stresses, defect topography and defect geometry. Practical applications of all results are discussed, and more effective means of ultrasonic inspection of austenitic weldments are suggested.

Induced visual illusions and gamma oscillations in human primary visual cortex

Using magnetoencephalography, we studied the spatiotemporal properties of cortical responses in terms of event-related synchronization and event-related desynchronization to a range of stripe patterns in subjects with no neurological disorders. These stripes are known for their tendency to induce a range of abnormal sensations, such as illusions, nausea, dizziness, headache and attacks of pattern-sensitive epilepsy. The optimal stimulus must have specific physical properties, and maximum abnormalities occur at specific spatial frequency and contrast. Despite individual differences in the severity of discomfort experienced, psychophysical studies have shown that most observers experience some degree of visual anomaly on viewing such patterns. In a separate experiment, subjects reported the incidence of illusions and discomfort to each pattern. We found maximal cortical power in the gamma range (30-60 Hz) confined to the region of the primary visual cortex in response to patterns of 2-4 cycles per degree, peaking at 3 cycles per degree. This coincides with the peak of mean illusions and discomfort, also maximal for patterns of 2-4 cycles per degree. We show that gamma band activity in V1 is a narrow band function of spatial frequency. We hypothesize that the intrinsic properties of gamma oscillations may underlie visual discomfort and play a role in the onset of seizures.

Fault diagnosis scheme for open-circuit faults in switched reluctance motor drives using fast Fourier transform algorithm with bus current detection

Reliability of power converters is of crucial importance in switched reluctance motor drives used for safety-critical applications. Open-circuit faults in power converters will cause the motor to run in unbalanced states, and if left untreated, they will lead to damage to the motor and power modules, and even cause a catastrophic failure of the whole drive system. This study is focused on using a single current sensor to detect open-circuit faults accurately. An asymmetrical half-bridge converter is considered in this study and the faults of single-phase open and two-phase open are analysed. Three different bus positions are defined. On the basis of a fast Fourier transform algorithm with Blackman window interpolation, the bus current spectrums before and after open-circuit faults are analysed in details. Their fault characteristics are extracted accurately by the normalisations of the phase fundamental frequency component and double phase fundamental frequency component, and the fault characteristics of the three bus detection schemes are also compared. The open-circuit faults can be located by finding the relationship between the bus current and rotor position. The effectiveness of the proposed diagnosis method is validated by the simulation results and experimental tests.

Decision theory to support evacuation in advance of catastrophic disaster including modular influence diagrams and spatial data analysis.

DUE TO INCOMPLETE PAPERWORK, ONLY AVAILABLE FOR CONSULTATION AT ASTON UNIVERSITY LIBRARY AND INFORMATION SERVICES WITH PRIOR ARRANGEMENT

Deliberate and spontaneous sensations of disembodiment:capacity or flaw?

Introduction: Hallucinations that involve shifts in the subjectively experienced location of the self, have been termed “out-of-body experiences” (OBEs). Early psychiatric accounts cast OBEs as a specific instance of depersonalisation and derealisation disorder (DPD-DR). However, during feelings of alienation and lack of body realism in DPD-DR the self is experienced within the physical body. Deliberate forms of “disembodiment” enable humans to imagine another’s visuo-spatial perspective taking (VPT), thus, if a strong relationship between deliberate and spontaneous forms of disembodiment could be revealed, then uncontrolled OBEs could be “the other side of the coin” of a uniquely human capacity. Methods: We present a narrative review of behavioural and neuroimaging work emphasising methodological and theoretical aspects of OBE and VPT research and a potential relationship. Results: Results regarding a direct behavioural relationship between VPT and OBE are mixed and we discuss reasons by pointing out the importance of using realistic tasks and recruiting genuine OBEers instead of general DPD-DR patients. Furthermore, we review neuroimaging evidence showing overlapping neural substrates between VPT and OBE, providing a strong argument for a relationship between the two processes. Conclusions: We conclude that OBE should be regarded as a necessary implication of VPT ability in humans, or even as a necessary and potentially sufficient condition for the evolution of VPT.

Factor analysis and discriminant validity:a brief review of some practical issues

Growth in availability and ability of modern statistical software has resulted in greater numbers of research techniques being applied across the marketing discipline. However, with such advances come concerns that techniques may be misinterpreted by researchers. This issue is critical since misinterpretation could cause erroneous findings. This paper investigates some assumptions regarding: 1) the assessment of discriminant validity; and 2) what confirmatory factor analysis accomplishes. Examples that address these points are presented, and some procedural remedies are suggested based upon the literature. This paper is, therefore, primarily concerned with the development of measurement theory and practice. If advances in theory development are not based upon sound methodological practice, we as researchers could be basing our work upon shaky foundations.

Stabilisation of isocyanate cross linked polybutadiene binder

Isocyanate cross-linked hydroxy terminated polybutadiene is used as a binder for solid rocket propellant. Rocket motors containing this propellant require a storage life of at least 20 years. During storage it has been found that the important rubbery properties of the binder can be lost due to oxidative cross-linking of the polybutadiene chains. This could cause catastrophic failure when the rocket motor is required. At present the bis-hindered phenol Calco 2246 is used as a thermal oxidative stabiliser, but it's performance is only adequate. This has led to the search for a more efficient stabiliser system. To hasten the evaluation of new antioxidant systems the use of dynamic thermal analysis was investigated. Results showed that a tentative relationship existed between predictions by thermal analysis and the long term oven ageing for simple single antioxidant systems. But for more complex systems containing either autosynergistic or mixed antioxidants no relationship was observed suggesting that results for such an "accelerated" technique cannot be used for the purpose of extrapolation for long term performance. This was attributed to the short time and more aggressive condition used (hjgher temperature and oxygen rich atmosphere in thermal analysis) altering the mechanism of action of the antioxidants and not allowing time for co-operative effect of the combined antioxidant system to form. One potential problem for the binder system is the use of an diisocyanate as a cross-linking agent. This reacts with the hydroxyl hydrogen on the polymer as well as other active hydrogens such as those contained in a number of antioxidants, affecting both cross-linking and antioxidant effectiveness. Studies in this work showed that only antioxidants containing amine moieties have a significant affect on binder preparation, with the phenolic antioxidants not reacting. This is due to the greater nucleophilicity of the amines. Investigation of a range of antioxidant systems, including potentially homo, hetero and autosynergistic systems, has highlighted a number of systems which show considerably greater effectiveness than the currently used antioxidant Calco 2246. The only single antioxidant which showed improvement was the partially unhindered phenol y-Tocopherol. Of the mixed systems combinations of the sulphur containing antioxidants e.g. DLTP with higher levels of chain-breaking antioxidants, especially Calco 2246, were the most promising. Also the homosynergistic mix of an aromatic amine and a phenol was seen to be very effective but the results were inconsistent. This inconsistency could be explained by the method of sample preparation used. It was shown that the efficiency of a number of antioxidant.s could be dramatically improved by the use of ultrasound during the mixing stage of preparation. The reason for this increase in performance is unclear but in the case of the homosynergistic amine/phenol mix both more efficient mixing and/or the production of a novel mechanism of action are suggested

Deep hole drilling with twist drills: aspects of the CNC process and its real time monitoring and adaptive control

Deep hole drilling is one of the most complicated metal cutting processes and one of the most difficult to perform on CNC machine-tools or machining centres under conditions of limited manpower or unmanned operation. This research work investigates aspects of the deep hole drilling process with small diameter twist drills and presents a prototype system for real time process monitoring and adaptive control; two main research objectives are fulfilled in particular : First objective is the experimental investigation of the mechanics of the deep hole drilling process, using twist drills without internal coolant supply, in the range of diarneters Ø 2.4 to Ø4.5 mm and working length up to 40 diameters. The definition of the problems associated with the low strength of these tools and the study of mechanisms of catastrophic failure which manifest themselves well before and along with the classic mechanism of tool wear. The relationships between drilling thrust and torque with the depth of penetration and the various machining conditions are also investigated and the experimental evidence suggests that the process is inherently unstable at depths beyond a few diameters. Second objective is the design and implementation of a system for intelligent CNC deep hole drilling, the main task of which is to ensure integrity of the process and the safety of the tool and the workpiece. This task is achieved by means of interfacing the CNC system of the machine tool to an external computer which performs the following functions: On-line monitoring of the drilling thrust and torque, adaptive control of feed rate, spindle speed and tool penetration (Z-axis), indirect monitoring of tool wear by pattern recognition of variations of the drilling thrust with cumulative cutting time and drilled depth, operation as a data base for tools and workpieces and finally issuing of alarms and diagnostic messages.

The cutting performance of sialon ceramic tools

The thesis deals with a research programme in which the cutting performance of a new generation of ceramic cutting tool material is evaluated using the turning process. In part one, the performance of commercial Kyon 2000 sialon ceramic inserts is studied when machining a hardened alloy steel under a wide range of cutting conditions. The aim is to formulate a pattern of machining behaviour in which tool wear is related to a theoretical interpretation of the temperatures and stresses generated by the chip-tool interaction. The work involves a correlation of wear measurement and metallographic examination of the wear area with the measurable cutting data. Four main tool failure modes are recognised: (a) flank and crater wear (b) grooving wear (c) deformation wear and (d) brittle failure Results indicate catastrophic edge breakdown under certain conditions. Accordingly in part two, the edge geometry is modified to give a double rake tool; a negative/positive combination. The results are reported for a range of workpiece materials under orthogonal cutting conditions. Significant improvements in the cutting performance are achieved. The improvements are explained by a study of process parameters; cutting forces, chip thickness ratio, chip contact length, temperature distribution, stress distribution and chip formation. In part three, improvements in tool performance are shown to arise when the edge chamfer on a single rake tool is modified. Under optimum edge chamfer conditions a substantial increase in tool life is obtained compared with the commercial cutting geometry.

Reduced attentional capacity, but normal processing speed and shifting of attention in developmental dyslexia: evidence from a serial task

We report the performance of a group of adult dyslexics and matched controls in an array-matching task where two strings of either consonants or symbols are presented side by side and have to be judged to be the same or different. The arrays may differ either in the order or identity of two adjacent characters. This task does not require naming – which has been argued to be the cause of dyslexics’ difficulty in processing visual arrays – but, instead, has a strong serial component as demonstrated by the fact that, in both groups, Reaction times (RTs) increase monotonically with position of a mismatch. The dyslexics are clearly impaired in all conditions and performance in the identity conditions predicts performance across orthographic tasks even after age, performance IQ and phonology are partialled out. Moreover, the shapes of serial position curves are revealing of the underlying impairment. In the dyslexics, RTs increase with position at the same rate as in the controls (lines are parallel) ruling out reduced processing speed or difficulties in shifting attention. Instead, error rates show a catastrophic increase for positions which are either searched later or more subject to interference. These results are consistent with a reduction in the attentional capacity needed in a serial task to bind together identity and positional information. This capacity is best seen as a reduction in the number of spotlights into which attention can be split to process information at different locations rather than as a more generic reduction of resources which would also affect processing the details of single objects.

The structure and dynamics of saxicolous lichen communities

The saxicolous lichen vegetation on Ordovician slate rock at the mouth of the River Dovey, South Merionethshire, Wales was described in relation to several environmental variables which include aspect, slope angle, light intensity, rock porosity, rock microtopography and rock stability. Each of the measured environmental variables was shown to influence the lichen vegetation. A number of groups of species which were characteristic of certain environments were described. The data from the saxicolous lichen communities were analysed using multivariate analysis. Qualitative and quantitative data were ordinated, the qualitative data being easier to interpret ecologically, and site number (which reflects distance from the sea and altitude), rock porosity and light intensity were shown to be important environmental variables. A classification of the data was also carried out. The results of the ordination and classification were combined together and a model constructed which describes saxicolous lichen vegetation. A method which uses the model as an aid to the design and interpretation of field experiments is described. The model is applied to an experiment which investigates the effect on growth of transplanting four saxicolous lichens to different aspects. Growth was inhibited in Physcia orbicularis and Parmelia conspersa on rock surfaces of northwest aspect compared with growth on rock surfaces of southeast aspect. Growth was inhibited in Parmelia glabratula ssp. fuliginosa on rock surfaces of southeast aspect compared with rock surfaces of northwesr aspect. The growth of Parmelia saxatilis was similar at both southeast and northwesr aspects. Growth inhibition or stimulation in thalli of Physcia orbicularis, Parmelia conspersa and Parmelia glabratula ssp. fuliginosa after transplantation was consistent with the predictions of the model while the results for Parmelia saxatilis were not as expected. There was evidence that the frequency of Parmelia conspersa and Parmelia glabratula at a site is related to an effect of the environment on the growth of the thalli. There was also evidence that the frequency of Physcia orbicularis at a site is related to an effect of the environment on the establishment phase of the thalli and for the competitive exclusion of Parmelia saxatilis thalli from southeast facing rock surfaces. The distribution of lichens in relation to height on nine rock surfaces was investigated. It was suggested that the distribution of the lichens was influenced by microclimatic factors which are related to height on the rock, environmental variables which are associated with the rock substratum (e.g. rock porosity and rock microtopography) and by historical factors. The pattern of one crustose and one foliose lichen on four rock surfaces of different aspect and slope was investigated. On the vertically inclined surface the density of small thalli of Buellia aethalea and Parmelia glabratula ssp fuliginosa was correlated with the microtopography of the surface in transects horizontally across the rock surface but not in transects vertically down the rock surface. there were consitent differences in the scale and intensity of pattern horizontally and vertically and also a decrease in the intensity of pattern vertically as the slope of the rock surface decreased. These results were consistent with the suggestion of a gradient of microclimatic factors up the rock. The differences in the scale and intensity of pattern in different size classes in the population were consistent with the changes in pattern with time which have been shown to occur during succession in sand dune and salt marsh vegetation. The relationship between thallus size and height on a rock surface and between the radial growth rate and location of a thallus on a rock surface were investigated. Thalli of Parmelia glabratula ssp. fuliginosa were larger at the top of the rock surface than at the bottom and the data were consistent with the suggestion that the colonisation of the rock surface began at the top and, in time, spread downwards. The radial growth rate of the thalli could not be related to variation in slope, porosity, microtopography or directly to height on the rock but could be related to the horizontal location of the thalli on the rock. These results were consistent with the suggestion that here is a gradient of microclimatic factors across the rock surface which is also modified by height on the rock surface. The succession of lichen communities was described by relating the vegetation to rock porosity, rock microtopography, species diversity and rock stability. An initial stage dominated by crustose lichens leads to communities dominated by crustose, foliose and fruticose species. In the late stages of the succession on some rock surfaces crustose species again become dominant. The occurrence of the climax state and cyclic vegetation change in lichen communities are discussed. A mthod of estimating the age structure of a lichen population by relating thallus size to growth rate is described. The sources of error in the method are discussed in some detail and several refinements suggested to increase the accuracy of the method. The population dynamics of Parmelia glabratula ssp. fuliginosa was investigated by applying life tables to the age structures of eight different populations. The data were consistent with a period of relatively constant recruitment of thalli into the populations. Mortality in lichen populations was divided into deaths which occur after fragmentation of the thallus and deaths which occur after catastrophic environmental events. THe data suggest that the rate of fragmenting death is dependent on the age of the thallus while the rate of catastrophic death is dependent on the number of thalli established in an age class. A comparison of the numbers of thalli in each age class in the eight populations suggested that population density is controlled firstly, by climate and secondly, by variables related to the local rock surface environment. The rate of fragmenting death is related to the diversity of the community and the influence of diversity together with environmental variables in fluctuating or cyclic changes in population number.

Is pregnancy a teachable moment for diet and physical activity behaviour change? An interpretative phenomenological analysis of the experiences of women during their first pregnancy

OBJECTIVES: Pregnancy may provide a 'teachable moment' for positive health behaviour change, as a time when women are both motivated towards health and in regular contact with health care professionals. This study aimed to investigate whether women's experiences of pregnancy indicate that they would be receptive to behaviour change during this period. DESIGN: Qualitative interview study. METHODS: Using interpretative phenomenological analysis, this study details how seven women made decisions about their physical activity and dietary behaviour during their first pregnancy. RESULTS: Two women had required fertility treatment to conceive. Their behaviour was driven by anxiety and a drive to minimize potential risks to the pregnancy. This included detailed information seeking and strict adherence to diet and physical activity recommendations. However, the majority of women described behaviour change as 'automatic', adopting a new lifestyle immediately upon discovering their pregnancy. Diet and physical activity were influenced by what these women perceived to be normal or acceptable during pregnancy (largely based on observations of others) and internal drivers, including bodily signals and a desire to retain some of their pre-pregnancy self-identity. More reasoned assessments regarding benefits for them and their baby were less prevalent and influential. CONCLUSIONS: Findings suggest that for women who conceived relatively easily, diet and physical activity behaviour during pregnancy is primarily based upon a combination of automatic judgements, physical sensations, and perceptions of what pregnant women are supposed to do. Health professionals and other credible sources appear to exert less influence. As such, pregnancy alone may not create a 'teachable moment'. Statement of contribution What is already known on this subject? Significant life events can be cues to action with relation to health behaviour change. However, much of the empirical research in this area has focused on negative health experiences such as receiving a false-positive screening result and hospitalization, and in relation to unequivocally negative behaviours such as smoking. It is often suggested that pregnancy, as a major life event, is a 'teachable moment' (TM) for lifestyle behaviour change due to an increase in motivation towards health and regular contact with health professionals. However, there is limited evidence for the utility of the TM model in predicting or promoting behaviour change. What does this study add? Two groups of women emerged from our study: the women who had experienced difficulties in conceiving and had received fertility treatment, and those who had conceived without intervention. The former group's experience of pregnancy was characterized by a sense of vulnerability and anxiety over sustaining the pregnancy which influenced every choice they made about their diet and physical activity. For the latter group, decisions about diet and physical activity were made immediately upon discovering their pregnancy, based upon a combination of automatic judgements, physical sensations, and perceptions of what is normal or 'good' for pregnancy. Among women with relatively trouble-free conception and pregnancy experiences, the necessary conditions may not be present to create a 'teachable moment'. This is due to a combination of a reliance on non-reflective decision-making, perception of low risk, and little change in affective response or self-concept.

In situ diagnostics and prognostics of wire bonding faults in IGBT modules for electric vehicle drives

This paper presents a diagnostic and prognostic condition monitoring method for insulated-gate bipolar transistor (IGBT) power modules for use primarily in electric vehicle applications. The wire-bond-related failure, one of the most commonly observed packaging failures, is investigated by analytical and experimental methods using the on-state voltage drop as a failure indicator. A sophisticated test bench is developed to generate and apply the required current/power pulses to the device under test. The proposed method is capable of detecting small changes in the failure indicators of the IGBTs and freewheeling diodes and its effectiveness is validated experimentally. The novelty of the work lies in the accurate online testing capacity for diagnostics and prognostics of the power module with a focus on the wire bonding faults, by injecting external currents into the power unit during the idle time. Test results show that the IGBT may sustain a loss of half the bond wires before the impending fault becomes catastrophic. The measurement circuitry can be embedded in the IGBT drive circuits and the measurements can be performed in situ when the electric vehicle stops in stop-and-go, red light traffic conditions, or during routine servicing.