Design, modeling and construction of a novel ablative fast pyrolysis reactor and product collection system

The objective of this work was to design, construct and commission a new ablative pyrolysis reactor and a high efficiency product collection system. The reactor was to have a nominal throughput of 10 kg/11r of dry biomass and be inherently scalable up to an industrial scale application of 10 tones/hr. The whole process consists of a bladed ablative pyrolysis reactor, two high efficiency cyclones for char removal and a disk and doughnut quench column combined with a wet walled electrostatic precipitator, which is directly mounted on top, for liquids collection. In order to aid design and scale-up calculations, detailed mathematical modelling was undertaken of the reaction system enabling sizes, efficiencies and operating conditions to be determined. Specifically, a modular approach was taken due to the iterative nature of some of the design methodologies, with the output from one module being the input to the next. Separate modules were developed for the determination of the biomass ablation rate, specification of the reactor capacity, cyclone design, quench column design and electrostatic precipitator design. These models enabled a rigorous design protocol to be developed capable of specifying the required reactor and product collection system size for specified biomass throughputs, operating conditions and collection efficiencies. The reactor proved capable of generating an ablation rate of 0.63 mm/s for pine wood at a temperature of 525 'DC with a relative velocity between the heated surface and reacting biomass particle of 12.1 m/s. The reactor achieved a maximum throughput of 2.3 kg/hr, which was the maximum the biomass feeder could supply. The reactor is capable of being operated at a far higher throughput but this would require a new feeder and drive motor to be purchased. Modelling showed that the reactor is capable of achieving a reactor throughput of approximately 30 kg/hr. This is an area that should be considered for the future as the reactor is currently operating well below its theoretical maximum. Calculations show that the current product collection system could operate efficiently up to a maximum feed rate of 10 kg/Fir, provided the inert gas supply was adjusted accordingly to keep the vapour residence time in the electrostatic precipitator above one second. Operation above 10 kg/hr would require some modifications to the product collection system. Eight experimental runs were documented and considered successful, more were attempted but due to equipment failure had to be abandoned. This does not detract from the fact that the reactor and product collection system design was extremely efficient. The maximum total liquid yield was 64.9 % liquid yields on a dry wood fed basis. It is considered that the liquid yield would have been higher had there been sufficient development time to overcome certain operational difficulties and if longer operating runs had been attempted to offset product losses occurring due to the difficulties in collecting all available product from a large scale collection unit. The liquids collection system was highly efficient and modeling determined a liquid collection efficiency of above 99% on a mass basis. This was validated due to the fact that a dry ice/acetone condenser and a cotton wool filter downstream of the collection unit enabled mass measurements of the amount of condensable product exiting the product collection unit. This showed that the collection efficiency was in excess of 99% on a mass basis.

Improvement of bio-oil stability in wood pyrolysis process

Pyrolysis is one of several thermochemical technologies that convert solid biomass into more useful and valuable bio-fuels. Pyrolysis is thermal degradation in the complete or partial absence of oxygen. Under carefully controlled conditions, solid biomass can be converted to a liquid known as bie-oil in 75% yield on dry feed. Bio-oil can be used as a fuel but has the drawback of having a high level of oxygen due to the presence of a complex mixture of molecular fragments of cellulose, hemicellulose and lignin polymers. Also, bio-oil has a number of problems in use including high initial viscosity, instability resulting in increased viscosity or phase separation and high solids content. Much effort has been spent on upgrading bio-oil into a more usable liquid fuel, either by modifying the liquid or by major chemical and catalytic conversion to hydrocarbons. The overall primary objective was to improve oil stability by exploring different ways. The first was to detennine the effect of feed moisture content on bio-oil stability. The second method was to try to improve bio-oil stability by partially oxygenated pyrolysis. The third one was to improve stability by co-pyrolysis with methanol. The project was carried out on an existing laboratory pyrolysis reactor system, which works well with this project without redesign or modification too much. During the finishing stages of this project, it was found that the temperature of the condenser in the product collection system had a marked impact on pyrolysis liquid stability. This was discussed in this work and further recommendation given. The quantity of water coming from the feedstock and the pyrolysis reaction is important to liquid stability. In the present work the feedstock moisture content was varied and pyrolysis experiments were carried out over a range of temperatures. The quality of the bio-oil produced was measured as water content, initial viscosity and stability. The result showed that moderate (7.3-12.8 % moisture) feedstock moisture led to more stable bio-oil. One of drawbacks of bio-oil was its instability due to containing unstable oxygenated chemicals. Catalytic hydrotreatment of the oil and zeolite cracking of pyrolysis vapour were discllssed by many researchers, the processes were intended to eliminate oxygen in the bio-oil. In this work an alternative way oxygenated pyrolysis was introduced in order to reduce oil instability, which was intended to oxidise unstable oxygenated chemicals in the bio-oil. The results showed that liquid stability was improved by oxygen addition during the pyrolysis of beech wood at an optimum air factor of about 0.09-0.15. Methanol as a postproduction additive to bio-oil has been studied by many researchers and the most effective result came from adding methanol to oil just after production. Co-pyrolysis of spruce wood with methanol was undertaken in the present work and it was found that methanol improved liquid stability as a co-pyrolysis solvent but was no more effective than when used as a postproduction additive.

A study of load support and other criteria appropriate to the selection of industrial conveyor belts

A study of conveying practice demonstrates that belt conveyors provide a versatile and. much-used method of transporting bulk materials, but a review of belting manufacturers' design procedures shows that belt design and selection rules are often based on experience with all-cotton belts no longer in common use, and are net completely relevant to modern synthetic constructions. In particular, provision of the property "load support", which was not critical with cotton belts, is shown to determine the outcome of most belt selection exercises and lead to gross over specification of other design properties in many cases. The results of an original experimental investigation into this property, carried out to determine the belt and conveyor parameters that affect it, how the major role that belt stiffness plays in its provision; the basis for a belt stiffness test relevant to service conditions is given. A proposal for a more rational method of specifying load support data results from the work, but correlation of the test results with service performance is necessary before the absolute toad support capability required from a belt for given working conditions can be quantified. A study to attain this correlation is the major proposal for future work resulting from the present investigation, but a full review of the literature on conveyor design and a study of present practice within the belting industry demonstrate other, less critical, factors that could profitably be investigated. It is suggested that the most suitable method of studying these would be a rational data collection system to provide information on various facets of belt service behaviour; a basis for such a system is proposed. In addition to the work above, proposals for simplifying the present belt selection methods are made and a strain transducer suitable for use in future experimental investigations is developed.

Clogging in horizontal subsurface flow constructed wetlands

Horizontal Subsurface Flow Treatment Wetlands (HSSF TWs) are used by Severn Trent Water as a low-cost tertiary wastewater treatment for rural locations. Experience has shown that clogging is a major operational problem that reduces HSSF TW lifetime. Clogging is caused by an accumulation of secondary wastewater solids from upstream processes and decomposing leaf litter. Clogging occurs as a sludge layer where wastewater is loaded on the surface of the bed at the inlet. Severn Trent systems receive relatively high hydraulic loading rates, which causes overland flow and reduces the ability to mineralise surface sludge accumulations. A novel apparatus and method, the Aston Permeameter, was created to measure hydraulic conductivity in situ. Accuracy is ±30 %, which was considered adequate given that conductivity in clogged systems varies by several orders of magnitude. The Aston Permeameter was used to perform 20 separate tests on 13 different HSSF TWs in the UK and the US. The minimum conductivity measured was 0.03 m/d at Fenny Compton (compared with 5,000 m/d clean conductivity), which was caused by an accumulation of construction fines in one part of the bed. Most systems displayed a 2 to 3 order of magnitude variation in conductivity in each dimension. Statistically significant transverse variations in conductivity were found in 70% of the systems. Clogging at the inlet and outlet was generally highest where flow enters the influent distribution and exits the effluent collection system, respectively. Surface conductivity was lower in systems with dense vegetation because plant canopies reduce surface evapotranspiration and decelerate sludge mineralisation. An equation was derived to describe how the water table profile is influenced by overland flow, spatial variations in conductivity and clogging. The equation is calibrated using a single parameter, the Clog Factor (CF), which represents the equivalent loss of porosity that would reproduce measured conductivity according to the Kozeny-Carman Equation. The CF varies from 0 for ideal conditions to 1 for completely clogged conditions. Minimum CF was 0.54 for a system that had recently been refurbished, which represents the deviation from ideal conditions due to characteristics of non-ideal media such as particle size distribution and morphology. Maximum CF was 0.90 for a 15 year old system that exhibited sludge accumulation and overland flow across the majority of the bed. A Finite Element Model of a 15 m long HSSF TW was used to indicate how hydraulics and hydrodynamics vary as CF increases. It was found that as CF increases from 0.55 to 0.65 the subsurface wetted area increases, which causes mean hydraulic residence time to increase from 0.16 days to 0.18 days. As CF increases from 0.65 to 0.90, the extent of overland flow increases from 1.8 m to 13.1 m, which reduces hydraulic efficiency from 37 % to 12 % and reduces mean residence time to 0.08 days.

A decision support system for waste collection management and its potential improvement with Radio-Frequency Identification Technology (RFID)

Due to vigorous globalisation and product proliferation in recent years, more waste has been produced by the soaring manufacturing activities. This has contributed to the significant need for an efficient waste management system to ensure, with all efforts, the waste is properly treated for recycling or disposed. This paper presents a Decision Support System (DSS) framework, based on Constraint Logic Programming (CLP), for the collection management of industrial waste (of all kinds) and discusses the potential employment of Radio-Frequency Identification Technology (RFID) to improve several critical procedures involved in managing waste collection. This paper also demonstrates a widely distributed and semi-structured network of waste producing enterprises (e.g. manufacturers) and waste processing enterprises (i.e. waste recycling/treatment stations) improving their operations planning by means of using the proposed DSS. The potential RFID applications to update and validate information in a continuous manner to bring value-added benefits to the waste collection business are also presented. © 2012 Inderscience Enterprises Ltd.

Design and development of agent-based procurement system to enhance business intelligence

The purpose of this research is to propose a procurement system across other disciplines and retrieved information with relevant parties so as to have a better co-ordination between supply and demand sides. This paper demonstrates how to analyze the data with an agent-based procurement system (APS) to re-engineer and improve the existing procurement process. The intelligence agents take the responsibility of searching the potential suppliers, negotiation with the short-listed suppliers and evaluating the performance of suppliers based on the selection criteria with mathematical model. Manufacturing firms and trading companies spend more than half of their sales dollar in the purchase of raw material and components. Efficient data collection with high accuracy is one of the key success factors to generate quality procurement which is to purchasing right material at right quality from right suppliers. In general, the enterprises spend a significant amount of resources on data collection and storage, but too little on facilitating data analysis and sharing. To validate the feasibility of the approach, a case study on a manufacturing small and medium-sized enterprise (SME) has been conducted. APS supports the data and information analyzing technique to facilitate the decision making such that the agent can enhance the negotiation and suppler evaluation efficiency by saving time and cost.

Die Sprache des Wahnsinns. Harald Kaas und sein Erzählband ‘Uhren und Meere’:Harald Kaas and his short story collection 'watches and seas'

This essay examines the only book published by the late Harald Kaas. His collection of short stories Uhren und Meere (1979), dealing with depictions of psycho-pathological states of mind, gained Kaas a short-lived notoriety as he himself was a certified schizophrenic possessing first-hand experience of psychiatric treatment. This essay sets out to investigate whether or to what extent the stories in Uhren und Meere can be understood as a document of the language of madness. It concludes that despite the biographical dimension of his schizophrenic experience, Kaas’s texts fail to voice an as it were unadulterated language of madness. However, when read in conjunction with his quasi-poetological interview statements, it is possible to determine the very nature of madness as a collapse of a logical system of language. Meaning that language cannot actively be used to express madness, while at the same time madness can express itself in a language that we necessarily fail to understand. The language of madness manifests itself as the madness of language.

Achieving cost competitiveness with an agent based integrated process planning and production scheduling system

From a manufacturing perspective, the efficiency of manufacturing operations (such as process planning and production scheduling) are the key element for enhancing manufacturing competence. Process planning and production scheduling functions have been traditionally treated as two separate activities, and have resulted in a range of inefficiencies. These include infeasible process plans, non-available/overloaded resources, high production costs, long production lead times, and so on. Above all, it is unlikely that the dynamic changes can be efficiently dealt with. Despite much research has been conducted to integrate process planning and production scheduling to generate optimised solutions to improve manufacturing efficiency, there is still a gap to achieve the competence required for the current global competitive market. In this research, the concept of multi-agent system (MAS) is adopted as a means to address the aforementioned gap. A MAS consists of a collection of intelligent autonomous agents able to solve complex problems. These agents possess their individual objectives and interact with each other to fulfil the global goal. This paper describes a novel use of an autonomous agent system to facilitate the integration of process planning and production scheduling functions to cope with unpredictable demands, in terms of uncertainties in product mix and demand pattern. The novelty lies with the currency-based iterative agent bidding mechanism to allow process planning and production scheduling options to be evaluated simultaneously, so as to search for an optimised, cost-effective solution. This agent based system aims to achieve manufacturing competence by means of enhancing the flexibility and agility of manufacturing enterprises.

A systems approach to public sector budgeting: the case of the planning, programming, budgeting system for the health and personal social services

The aim of this thesis is to examine the specific contextual factors affecting the applicability and development of the planning, programming, budgeting system (P.P.B.S.) as a systems approach to public sector budgeting. The concept of P.P.B.S. as a systems approach to public sector budgeting will first be developed and the preliminary hypothesis that general contextual factors may be classified under political, structural and cognitive headings will be put forward. This preliminary hypothesis will be developed and refined using American and early British experience. The refined hypothesis will then be tested in detail in the case of the English health and personal social services (H.P.S.S.), The reasons for this focus are that it is the most recent, the sole remaining, and the most significant example in British central government outside of defence, and is fairly representative of non-defence government programme areas. The method of data collection relies on the examination of unpublished and difficult to obtain central government, health and local authority documents, and interviews with senior civil servants and public officials. The conclusion will be that the political constraints on, or factors affecting P.P.B.S., vary with product characteristics and cultural imperatives on pluralistic decision-making; that structural constraints vary with the degree of coincidence of programme and organisation structure and with the degree of controllability of the organisation; and finally, that cognitive constraints vary according to product characteristics, organisational responsibilities, and analytical effort.

River basin surveillance using remotely sensed data: a water resources information management system

This thesis describes the development of an operational river basin water resources information management system. The river or drainage basin is the fundamental unit of the system; in both the modelling and prediction of hydrological processes, and in the monitoring of the effect of catchment management policies. A primary concern of the study is the collection of sufficient and sufficiently accurate information to model hydrological processes. Remote sensing, in combination with conventional point source measurement, can be a valuable source of information, but is often overlooked by hydrologists, due to the cost of acquisition and processing. This thesis describes a number of cost effective methods of acquiring remotely sensed imagery, from airborne video survey to real time ingestion of meteorological satellite data. Inexpensive micro-computer systems and peripherals are used throughout to process and manipulate the data. Spatial information systems provide a means of integrating these data with topographic and thematic cartographic data, and historical records. For the system to have any real potential the data must be stored in a readily accessible format and be easily manipulated within the database. The design of efficient man-machine interfaces and the use of software enginering methodologies are therefore included in this thesis as a major part of the design of the system. The use of low cost technologies, from micro-computers to video cameras, enables the introduction of water resources information management systems into developing countries where the potential benefits are greatest.

Multiterminal DC wind farm collection grid internal fault analysis and protection design

The multiterminal dc wind farm is a promising topology with a voltage-source inverter (VSI) connection at the onshore grid. Voltage-source converters (VSCs) are robust to ac-side fault conditions. However, they are vulnerable to dc faults on the dc side of the converter. This paper analyzes dc faults, their transients, and the resulting protection issues. Overcurrent faults are analyzed in detail and provide an insight into protection system design. The radial wind farm topology with star or string connection is considered. The outcomes may be applicable for VSCs in the multi-VSC dc wind farm collection grid and VSC-based high-voltage direct current (HVDC) offshore transmission systems.

Understanding data collection behaviour of mental health practitioners

Failure to detect patients at risk of attempting suicide can result in tragic consequences. Identifying risks earlier and more accurately helps prevent serious incidents occurring and is the objective of the GRiST clinical decision support system (CDSS). One of the problems it faces is high variability in the type and quantity of data submitted for patients, who are assessed in multiple contexts along the care pathway. Although GRiST identifies up to 138 patient cues to collect, only about half of them are relevant for any one patient and their roles may not be for risk evaluation but more for risk management. This paper explores the data collection behaviour of clinicians using GRiST to see whether it can elucidate which variables are important for risk evaluations and when. The GRiST CDSS is based on a cognitive model of human expertise manifested by a sophisticated hierarchical knowledge structure or tree. This structure is used by the GRiST interface to provide top-down controlled access to the patient data. Our research explores relationships between the answers given to these higher-level 'branch' questions to see whether they can help direct assessors to the most important data, depending on the patient profile and assessment context. The outcome is a model for dynamic data collection driven by the knowledge hierarchy. It has potential for improving other clinical decision support systems operating in domains with high dimensional data that are only partially collected and in a variety of combinations.

Medicines optimisation for young people with juvenile arthritis and other long-term conditions:system-level barriers to engagement

To explore the views of pharmacy and rheumatology stakeholders about system-related barriers to medicines optimisation activities with young people with long-term conditions. A three-phase consensus-building study comprising (1) focus groups with community and hospital pharmacists; (2) semi-structured telephone interviews with lay and professional adolescent rheumatology stakeholders and pharmacy policymakers, and (3) multidisciplinary discussion groups with community and hospital pharmacists and rheumatology staff. Qualitative verbatim transcripts from phases 1 and 2 were subjected to framework analysis. Themes from phase 1 underpinned a briefing for phase 2 interviewees. Themes from phases 1 and 2 generated elements of good pharmacy practice and current/future pharmacy roles for ranking in phase 3. Results from phase 3 prioritisation and ranking exercises were captured on self-completion data collection forms, entered into an Excel spreadsheet and subjected to descriptive statistical analysis. Institutional ethical approval was given by Aston University Health and Life Sciences Research Ethics Committee. Four focus groups were conducted with 18 pharmacists across England, Scotland and Wales (7 hospital, 10 community and 1 community/public health). Fifteen stakeholders took part in telephone interviews (3 pharmacist commissioners; 2 pharmacist policymakers; 2 pharmacy staff members (1 community and 1 hospital); 4 rheumatologists; 1 specialist nurse, and 3 lay juvenile arthritis advocates). Twenty-five participants took part in three discussion groups in adolescent rheumatology centres across England and Scotland (9 community pharmacists; 4 hospital pharmacists; 6 rheumatologists; 5 specialist nurses, and 1 physiotherapist). In all phases of the study, system-level issues were acknowledged as barriers to more engagement with young people and families. Community pharmacists in the focus groups reported that opportunities for engaging with young people were low if parents collected prescriptions alone, which was agreed by other stakeholders. Moreover, institutional/company prescription collection policies – an activity largely disallowed for a young person under 16 without an accompanying parent - were identified by hospital and community pharmacists as barriers to open discussion and engagement. Few community pharmacists reported using Medicines Use Review (England/Wales) or Chronic Medication Service (Scotland) as a medicines optimisation activity with young people; many were unsure about consent procedures. Despite these limitations, rheumatology stakeholders ranked highly the potential of pharmacists empowering young people with general health care skills, such as repeat prescription ordering. The pharmacy profession lacks vision for its role in the care of young people with long-term conditions. Pharmacists and rheumatology stakeholders identified system-level barriers to more engagement with young people who take medicines regularly. We acknowledge that the modest number of participants may have had a specific interest and thus bias for the topic, but this underscores their frank admission of the challenges. Professional guidance and policy, practice frameworks and institutional/company policies must promote flexibility for pharmacy staff to recognise and empower young people who are able to give consent and take responsibility for medicines activities. This will increase mutual confidence and trust, and foster pharmacy’s role in teaching general health care skills. In this way, pharmacists will be able to build long-term relationships with young people and families.