The acceptability of alcohol fuels for automobile engines

The aim of this project was to carry out an investigastion into suitable alternatives to gasoline for use in modern automobiles. The fuel would provide the western world with a means of extending the natural gasoline resources and the third world a way of cutting down their dependence on the oil producing countries for their energy supply. Alcohols, namely methanol and ethanol, provide this solution. They can be used as gasoline extenders or as fuels on their own.In order to fulfil the aims of the project a literature study was carried out to investigate methods and costs of producing these fuels. An experimental programme was then set up in which the performance of the alcohols was studied on a conventional engine. The engine used for this purpose was the Fiat 127 930cc four cylinder engine. This engine was used because of its popularity in the European countries. The Weber fixed jet carburettor, since it was designed to be used with gasoline, was adapted so that the alcohol fuels and the blends could be used in the most efficient way. This was mainly to take account of the lower heat content of the alcohols. The adaptation of the carburettor was in the form of enlarging the main metering jet. Allowances for the alcohol's lower specfic gravity were made during fuel metering.Owing to the low front end volatility of methanol and ethanol, it was expected that `start up' problems would occur. An experimental programme was set up to determine the temperature range for a minimum required percentage `take off' that would ease start-up since it was determined that a `take off' of about 5% v/v liquid in the vapour phase would be sufficient for starting. Additions such as iso-pentane and n-pentane were used to improve the front end volatility. This proved to be successful.The lower heat content of the alcohol fuels also meant that a greater charge of fuel would be required. This was seen to pose further problems with fuel distribution from the carburettor to the individual cylinders on a multicylinder engine. Since it was not possible to modify the existing manifold on the Fiat 127 engine, experimental tests on manifold geometry were carried out using the Ricardo E6 single cylinder variable compression engine. Results from these tests showed that the length, shape and cross-sectional area of the manifold play an important part in the distribution of the fuel entering the cylinder, ie. vapour phase, vapour/small liquid droplet/liquid film phase, vapour/large liquid droplet/liquid film phase etc.The solvent properties of the alcohols and their greater electrical conductivity suggested that the materials used on the engine would be prone to chemical attack. In order to determine the type and rate of chemical attack, an experimental programme was set up whereby carburettor and other components were immersed in the alcohols and in blends of alcohol with gasoline. The test fuels were aerated and in some instances kept at temperatures ranging from 50oC to 90oC. Results from these tests suggest that not all materials used in the conventional engine are equally suitable for use with alcohols and alcohol/gasoline blends. Aluminium for instance was severely attacked by methanol causing pitting and pin-holing in the surface.In general this whole experimental programme gave valuable information on the acceptability of substitute fuels. While the long term effects of alcohol use merit further study, it is clear that methanol and ethanol will be increasingly used in place of gasoline.

Automobile friction materials: a test instrument and technique for determining dynamic mechanical properties in relation to brake squeal

This study is primarily concerned with the problem of break-squeal in disc brakes, using moulded organic disc pads. Moulded organic friction materials are complex composites and due to this complexity it was thought that they are unlikely to be of uniform composition. Variation in composition would under certain conditions of the braking system, cause slight changes in its vibrational characteristics thus causing resonance in the high audio-frequency range. Dynamic mechanical propertes appear the most likely parameters to be related to a given composition's tendency to promote squeal. Since it was necessary to test under service conditions a review was made of all the available commercial test instruments but as none were suitable it was necessary to design and develop a new instrument. The final instrument design, based on longitudinal resonance, enabled modulus and damping to be determined over a wide range of temperatures and frequencies. This apparatus has commercial value since it is not restricted to friction material testing. Both used and unused pads were tested and although the cause of brake squeal was not definitely established, the results enabled formulation of a tentative theory of the possible conditions for brake squeal. The presence of a temperature of minimum damping was indicated which may be of use to braking design engineers. Some auxilIary testing was also performed to establish the effect of water, oil and brake fluid and also to determine the effect of the various components of friction materials.

An analysis of fatal accidents in agriculture in Great Britain

The number of fatal accidents in the agricultural, horticultural and forestry industry in Great Britain has declined from an annual rate of about 135 in the 1960's to its current level of about 50. Changes to the size and makeup of the population at risk mean that there has been no real improvement in fatal injury incidence rates for farmers. The Health and Safety Executives' (HSE) current system of accident investigation, recording, and analysis is directed primarily at identifying fault, allocating blame, and punishing wrongdoers. Relatively little information is recorded about the personal and organisational factors that contributed to, or failed to prevent accidents. To develop effective preventive strategies, it is important to establish whether errors by the victims and others, occur at the skills, rules, or knowledge level of functioning: are violations of some rule or procedure; or stem from failures to correctly appraise, or control a hazard. A modified version of the Hale and Glendon accident causation model was used to study 230 fatal accidents. Inspectors' original reports were examined and expert judgement applied to identify and categorise the errors committed by each of the parties involved. The highest proportion of errors that led directly to accidents occurred whilst the victims were operating at the knowledge level. The mix and proportion of errors varied considerably between different classes of victim and kind of accident. Different preventive strategies will be needed to address the problem areas identified.

Rural road accidents in Iran: analysis, comparison and the cost

In the general introduction of the road-accident phenomenon inside and outside Iran, the results of previous research-works and international conferences and seminars on road-safety have been reviewed. Also a sample-road between Tehran and Mashad has been investigated as a case-study. Examining the road-accident data and iriformation,first: the information presented in road-accident report-forms in developed countries is discussed and, second: the procedures for road-accident data collection in Iran are investigated in detail. The data supplied by Iran Road-Police Central Statistics Office, is analysed, different rates are computed, due comparisons with other nations are made, and the results are discussed. Also such analysis and comparisons are presented for different provinces of Iran. It is concluded that each province with its own natural, geographical, social and economical characteristics possesses its own reasons for the quality and quantity of road-accidents and therefore must receive its own appropriate remedial solutions. The question~ of "what is the cost of road-accidents", "why and how evaluate the cost", "what is the appropriate way of approach to such evaluation" are all discussed and then "the cost of road-accidents in Iran" based on two different approaches: "Gross National Output"and "court award" is computed. It is concluded that this cost is about 1.5 per cent of the country's national product. In Appendix 3 an impressive example is given of the trend of costs and benefits that can be attributed to investment in road-safety measures.

A comparison of road accidents in developing countries with special reference to Jamaica

This research was originally undertaken to aid the Jamaican government and the World Bank in making funding decisions relative to improvement of road systems and traffic control in Jamaica. An investigation of the frequency and causes of road accidents and an evaluation of their impact on the Jamaican economy were carried out, and a model system which might be applied was developed. It is believed that the importance of road accident economic and manpower losses to the survival of developing countries, such as Jamaica, cannot be overemphasized. It is suggested that the World Bank, in cooperation with national governments, has a role to play in alleviating this serious problem. Data was collected from such organizations as the Jamaica Ministry of Construction, Police Department, the World Bank, and the World Health Organization. A variety of methodologies were utilized to organize this data in useful and understandable forms. The most important conclusion of this research is that solvable problems in road systems and in traffic control result in the unnecessary loss of useful citizens, in both developed and developing countries. However, a lack of information and understanding regarding the impact of high rates of road accident death and injury on the national economy and stability of a country results in an apparent lack of concern. Having little internal expertise in the field of road accident prevention, developing countries usually hire consultants to help them address this problem. In the case of Jamaica, this practice has resulted in distrust and hard feelings between the Jamaican authorities and major organizations involved in the field. Jamaican officials have found confusing the recommendations of most experts contracted to study traffic safety. The attempts of foreign consultants to utilize a technological approach (the use of coding systems and computers), methods which do not appear cost-effective for Jamaica, have resulted in the expenditure of limited funds for studies which offer no feasible approach to the problem. This funding limitation, which hampers research and road improvement, could be alleviated by such organizations as the World Bank. The causes of high accident rates are many, it was found. Formulation of a plan to address this serious problem must take into account the current failure to appreciate the impact of a high level of road accidents on national economy and stability, inability to find a feasible approach to the problem, and inadequate funding. Such a plan is discussed in detail in the main text of this research.

Experiments for CFD-modelling of cooling water and Insulation debris two-phase flow phenomena during loss of coolant accidents

The knowledge of insulation debris generation and transport gains in importance regarding reactor safety research for PWR and BWR. The insulation debris released near the break consists of a mixture of very different fibres and particles concerning size, shape, consistence and other properties. Some fraction of the released insulation debris will be transported into the reactor sump where it may affect emergency core cooling. Experiments are performed to blast original samples of mineral wool insulation material by steam under original thermal-hydraulic break conditions of BWR. The gained fragments are used as initial specimen for further experiments at acrylic glass test facilities. The quasi ID-sinking behaviour of the insulation fragments are investigated in a water column by optical high speed video techniques and methods of image processing. Drag properties are derived from the measured sinking velocities of the fibres and observed geometric parameters for an adequate CFD modelling. In the test rig "Ring line-II" the influence of the insulation material on the head loss is investigated for debris loaded strainers. Correlations from the filter bed theory are adapted with experimental results and are used to model the flow resistance depending on particle load, filter bed porosity and parameters of the coolant flow. This concept also enables the simulation of a particular blocked strainer with CFDcodes. During the ongoing work further results of separate effect and integral experiments and the application and validation of the CFD-models for integral test facilities and original containment sump conditions are expected.