A hybrid measurement systems analysis and uncertainty of measurement approach for industrial measurement in the light controlled factory

The uncertainty of measurements must be quantified and considered in order to prove conformance with specifications and make other meaningful comparisons based on measurements. While there is a consistent methodology for the evaluation and expression of uncertainty within the metrology community industry frequently uses the alternative Measurement Systems Analysis methodology. This paper sets out to clarify the differences between uncertainty evaluation and MSA and presents a novel hybrid methodology for industrial measurement which enables a correct evaluation of measurement uncertainty while utilising the practical tools of MSA. In particular the use of Gage R&R ANOVA and Attribute Gage studies within a wider uncertainty evaluation framework is described. This enables in-line measurement data to be used to establish repeatability and reproducibility, without time consuming repeatability studies being carried out, while maintaining a complete consideration of all sources of uncertainty and therefore enabling conformance to be proven with a stated level of confidence. Such a rigorous approach to product verification will become increasingly important in the era of the Light Controlled Factory with metrology acting as the driving force to achieve the right first time and highly automated manufacture of high value large scale products such as aircraft, spacecraft and renewable power generation structures.

Combined bioreaction and separation in centrifugal fields

The aim of this work has been to investigate the principle of combined centrifugal bioreaction-separation. The production of dextran and fructose by the action of the enzyme dextransucrase on sucrose was employed to elucidate some of the principles of this type of process. Dextran is a valuable pharmaceutical product used mainly as a blood volume expander and blood flow improver whilst fructose is an important dietary product. The development of a single step process capable of the simultaneous biosynthesis of dextran and the separation of the fructose by-product should improve dextran yields whilst reducing capital and processing costs. This thesis shows for the first time that it is possible to conduct successful bioreaction-separations using a rate-zonal centrifugation technique. By layering thin zones of dextrasucrase enzyme onto sucrose gradients and centrifuging, very high molecular weight (MW) dextran-enzyme complexes were formed that rapidly sedimented through the sucrose substrate gradients under the influence of the applied centrifugal field. The low MW fructose by-product sedimented at reduced rates and was thus separated from the enzyme and dextran during the reaction. The MW distribution of dextran recovered from the centrifugal bioreactor was compared with that from a conventional batch bioreactor. The results indicated that the centrifugal bioreactor produced up to 100% more clinical dextran with MWs of between 12 000 and 98 000 at 20% w/w sucrose concentrations than conventional bioreactors. This was due to the removal of acceptor fructose molecules from the sedimenting reaction zone by the action of the centrifugal field. Higher proportions of unwanted lower MW dextran were found in the conventional bioreactor than in the centrifugal bioreactor-separator. The process was studied on a number of alternative centrifugal systems. A zonal rotor fitted with a reorienting gradient core proved most successful for the evaluation of bioreactor performance. Results indicated that viscosity build-up in the reactor must be minimised in order to increase the yields of dextran per unit time and improve product separation. A preliminary attempt at modelling the process has also been made.

An investigation of Albanian EFL teachers' decision-making in their use of CLT-oriented textbooks

Against a backdrop of ongoing educational reforms that seek to introduce Communicative Language Teaching (CLT) in Albanian primary and secondary state schools, Albanian teachers, among others, are officially required to use communication-based textbooks in their classes. Authorities in a growing number of countries that are seeking to improve and westernise their educational systems are also using communication-based textbooks as agents of change. Behind these actions, there is the commonly held belief that textbooks can be used to support teacher learning as they provide a visible framework teachers can follow. Communication-based textbooks are used in thousands of EFL classrooms around the world to help teachers to “fully understand and routinize change” (Hutchinson and Torres, 1994:323). However, empirical research on the role materials play in the classroom, and in particular the role of textbook as an agent of change, is still very little, and what does exist is rather inconclusive. This study aims to fulfill this gap. It is predominately a qualitative investigation into how and why four Albanian EFL teachers use Western teaching resources in their classes. Aiming at investigating the decision-making processes that teachers go through in their teaching, and specifically at investigating the relationship between Western-published textbooks, teachers’ decision making, and teachers’ classroom delivery, the current study contributes to an extensive discussion on the development of communicative L2 teaching concepts and methods, teacher decision making, as well as a growing discussion on how best to make institutional reforms effective, particularly in East-European ex-communist countries and in other developing countries. Findings from this research indicate that, prompted by the content of Western-published textbooks, the four research participants, who had received little formal training in CLT teaching, accommodated some communicative teaching behaviours into their teaching. The use of communicative textbooks, however, does not seem to account for radical, methodological changes in teachers’ practices. Teacher cognitions based on teachers’ previous learning experience are likely to act as a lens through which teachers judge classroom realities. As such, they shape, to a great degree, the decisions teachers make regarding the use of Western-published textbooks in their classes.

CO2 absorption into aqueous amine blended solutions containing monoethanolamine (MEA), N,N-dimethylethanolamine (DMEA), N,N-diethylethanolamine (DEEA) and 2-amino-2-methyl-1-propanol (AMP) for post-combustion capture processes

Presently monoethanolamine (MEA) remains the industrial standard solvent for CO2 capture processes. Operating issues relating to corrosion and degradation of MEA at high temperatures and concentrations, and in the presence of oxygen, in a traditional PCC process, have introduced the requisite for higher quality and costly stainless steels in the construction of capture equipment and the use of oxygen scavengers and corrosion inhibitors. While capture processes employing MEA have improved significantly in recent times there is a continued attraction towards alternative solvents systems which offer even more improvements. This movement includes aqueous amine blends which are gaining momentum as new generation solvents for CO2 capture processes. Given the exhaustive array of amines available to date endless opportunities exist to tune and tailor a solvent to deliver specific performance and physical properties in line with a desired capture process. The current work is focussed on the rationalisation of CO2 absorption behaviour in a series of aqueous amine blends incorporating monoethanolamine, N,N-dimethylethanolamine (DMEA), N,N-diethylethanolamine (DEEA) and 2-amino-2-methyl-1-propanol (AMP) as solvent components. Mass transfer/kinetic measurements have been performed using a wetted wall column (WWC) contactor at 40°C for a series of blends in which the blend properties including amine concentration, blend ratio, and CO2 loadings from 0.0-0.4 (moles CO2/total moles amine) were systematically varied and assessed. Equilibrium CO2 solubility in each of the blends has been estimated using a software tool developed in Matlab for the prediction of vapour liquid equilibrium using a combination of the known chemical equilibrium reactions and constants for the individual amine components which have been combined into a blend.From the CO2 mass transfer data the largest absorption rates were observed in blends containing 3M MEA/3M Am2 while the selection of the Am2 component had only a marginal impact on mass transfer rates. Overall, CO2 mass transfer in the fastest blends containing 3M MEA/3M Am2 was found to be only slightly lower than a 5M MEA solution at similar temperatures and CO2 loadings. In terms of equilibrium behaviour a slight decrease in the absorption capacity (moles CO2/mole amine) with increasing Am2 concentration in the blends with MEA was observed while cyclic capacity followed the opposite trend. Significant increases in cyclic capacity (26-111%) were observed in all blends when compared to MEA solutions at similar temperatures and total amine concentrations. In view of the reasonable compromise between CO2 absorption rate and capacity a blend containing 3M MEA and 3M AMP as blend components would represent a reasonable alternative in replacement of 5M MEA as a standalone solvent.

Momentum profits in alternative stock market structures

The aim of this study is to examine the relationship between momentum profitability and the stock market trading mechanism and is motivated by recent changes to the trading systems that have taken place on the London Stock Exchange. Since 1975 the London stock market has employed three different trading systems: a floor based system, a computerized dealer system called SEAQ and the automated auction system SETS. Since each new trading system has reduced the level of execution costs, one might expect, a priori, the magnitude of momentum profits to decline with each amendment to the trading system. However, the opposite empirical result is found showing that shares trading on the automated system generate higher momentum profits than those trading on the floor system and companies trading on the SETS system display greater momentum profitability than those trading on SEAQ. Our empirical results concur with the theoretical findings of the trader’s hesitation model of Du [Du, J., 2002. Heterogeneity in investor confidence and asset market under- and overreaction. Working paper] and the empirical findings of Arena et al. [Arena, M., Haggard, S., Yan, X., Price momentum and idiosyncratic volatility. Financial Review, in press].

Environmental scanning electron microscope imaging of vesicle systems

The structural characteristics of liposomes have been widely investigated and there is certainly a strong understanding of their morphological characteristics. Imaging of these systems, using techniques such as freeze-fracturing methods, transmission electron microscopy, and cryo-electron imaging, has allowed us to appreciate their bilayer structures and factors that influence this. However, there are a few methods that study these systems in their natural hydrated state; commonly, the liposomes are visualized after drying, staining and/or fixation of the vesicles. Environmental scanning electron microscopy (ESEM) offers the ability to image a liposome in its hydrated state without the need for prior sample preparation. We were the first to use ESEM to study the liposomes and niosomes, and have been able to dynamically follow the hydration of lipid films and changes in liposome suspensions as water condenses onto, or evaporates from, the sample in real-time. This provides an insight into the resistance of liposomes to coalescence during dehydration, thereby providing an alternative assay for liposome formulation and stability.

Vaccine adjuvant systems: enhancing the efficacy of sub-unit protein antigens

Vaccination remains a key tool in the protection and eradication of diseases. However, the development of new safe and effective vaccines is not easy. Various live organism based vaccines currently licensed, exhibit high efficacy; however, this benefit is associated with risk, due to the adverse reactions found with these vaccines. Therefore, in the development of vaccines, the associated risk-benefit issues need to be addressed. Sub-unit proteins offer a much safer alternative; however, their efficacy is low. The use of adjuvanted systems have proven to enhance the immunogenicity of these sub-unit vaccines through protection (i.e. preventing degradation of the antigen in vivo) and enhanced targeting of these antigens to professional antigen-presenting cells. Understanding of the immunological implications of the related disease will enable validation for the design and development of potential adjuvant systems. Novel adjuvant research involves the combination of both pharmaceutical analysis accompanied by detailed immunological investigations, whereby, pharmaceutically designed adjuvants are driven by an increased understanding of mechanisms of adjuvant activity, largely facilitated by description of highly specific innate immune recognition of components usually associated with the presence of invading bacteria or virus. The majority of pharmaceutical based adjuvants currently being investigated are particulate based delivery systems, such as liposome formulations. As an adjuvant, liposomes have been shown to enhance immunity against the associated disease particularly when a cationic lipid is used within the formulation. In addition, the inclusion of components such as immunomodulators, further enhance immunity. Within this review, the use and application of effective adjuvants is investigated, with particular emphasis on liposomal-based systems. The mechanisms of adjuvant activity, analysis of complex immunological characteristics and formulation and delivery of these vaccines are considered.

The tribology of linear tape recording systems

This thesis is devoted to the tribology at the head~to~tape interface of linear tape recording systems, OnStream ADRTM system being used as an experimental platform, Combining experimental characterisation with computer modelling, a comprehensive picture of the mechanisms involved in a tape recording system is drawn. The work is designed to isolate the mechanisms responsible for the physical spacing between head and tape with the aim of minimising spacing losses and errors and optimising signal output. Standard heads-used in ADR current products-and prototype heads- DLC and SPL coated and dummy heads built from a AI203-TiC and alternative single-phase ceramics intended to constitute the head tape-bearing surface-are tested in controlled environment for up to 500 hours (exceptionally 1000 hours), Evidences of wear on the standard head are mainly observable as a preferential wear of the TiC phase of the AI203-TiC ceramic, The TiC grains are believed to delaminate due to a fatigue wear mechanism, a hypothesis further confirmed via modelling, locating the maximum von Mises equivalent stress at a depth equivalent to the TiC recession (20 to 30 nm). Debris of TiC delaminated residues is moreover found trapped within the pole-tip recession, assumed therefore to provide three~body abrasive particles, thus increasing the pole-tip recession. Iron rich stain is found over the cycled standard head surface (preferentially over the pole-tip and to a lesser extent over the TiC grains) at any environment condition except high temperature/humidity, where mainly organic stain was apparent, Temperature (locally or globally) affects staining rate and aspect; stain transfer is generally promoted at high temperature. Humidity affects transfer rate and quantity; low humidity produces, thinner stains at higher rate. Stain generally targets preferentially head materials with high electrical conductivity, i.e. Permalloy and TiC. Stains are found to decrease the friction at the head-to-tape interface, delay the TiC recession hollow-out and act as a protective soft coating reducing the pole-tip recession. This is obviously at the expense of an additional spacing at the head-to-tape interface of the order of 20 nm. Two kinds of wear resistant coating are tested: diamond like carbon (DLC) and superprotective layer (SPL), 10 nm and 20 to 40 nm thick, respectively. DLC coating disappears within 100 hours due possibly to abrasive and fatigue wear. SPL coatings are generally more resistant, particularly at high temperature and low humidity, possibly in relation with stain transfer. 20 nm coatings are found to rely on the substrate wear behaviour whereas 40 nm coatings are found to rely on the adhesive strength at the coating/substrate interface. These observations seem to locate the wear-driving forces 40 nm below the surface, hence indicate that for coatings in the 10 nm thickness range-· i,e. compatible with high-density recording-the substrate resistance must be taken into account. Single-phase ceramic as candidate for wear-resistant tape-bearing surface are tested in form of full-contour dummy-heads. The absence of a second phase eliminates the preferential wear observed at the AI203-TiC surface; very low wear rates and no evidence of brittle fracture are observed.

Motivations to deposit:two approaches to Open Educational Resources (OER) within Languages and Social Sciences (LSS) at Aston University

In Spring 2009, the School of Languages and Social Sciences (LSS) at Aston University responded to a JISC (Joint Information Systems Committee) and Higher Education Academy (HEA) call for partners in Open Educational Resources (OER) projects. This led to participation in not one, but two different OER projects from within one small School of the University. This paper will share, from this unusual position, the experience of our English tutors, who participated in the HumBox Project, led by Languages, Linguistics and Area Studies (LLAS) and will compare the approach taken with the Sociology partnership in the C-SAP OER Project , led by the Centre for Sociology, Anthropology and Politics (C-SAP). These two HEA Subject Centre-led projects have taken different approaches to the challenges of encouraging tutors to deposit teaching resources, as on ongoing process, for others to openly access, download and re-purpose. As the projects draw to a close, findings will be discussed, in relation to the JISC OER call, with an emphasis on examining the language and discourses from the two collaborations to see where there are shared issues and outcomes, or different subject specific concerns to consider.

Developments in assessment and teaching methodologies in modern languages in England and France in response to educational reform (1975-1985)

This comparative study considers the main causative factors for change in recent years in the teaching of modern languages in England and France and seeks to contribute, in a general sense, to the understanding of change in comparable institutions. In England by 1975 the teaching of modern languages in the comprehensive schools was seen to be inappropriate to the needs of children of the whole ability-range. A combination of the external factor of the Council of Europe initiative in devising a needs-based learning approach for adult learners, and the internal factor of teacher-based initiatives in developing a graded-objectives learning approach for the less-able, has reversed this situation to some extent. The study examines and evaluates this reversal, and, in addition, assesses teachers' attitudes towards, and understanding of, the changes involved. In France the imposition of `la reforme Haby' in 1977 and the creation of `le college unique' were the main external factors for change. The subsequent failure of the reform and the socialist government's support of decentralisation policies returning the initiative for renewal to schools are examined and evaluated, as are the internal factors for changes in language-teaching - `groupes de niveau' and the creation of `equipes pedagogiques'. In both countries changes in the function of examinations at 15/16 plus are examined. The final chapter compared the changes in both education systems.

An iterative-style approach to constructing intelligent tutoring systems in mathematics

Mathematics is highly structured and also underpins most of science and engineering. For this reason, it has proved a very suitable domain for Intelligent Tutoring System (ITS) research, with the result that probably more tutoring systems have been constructed for the domain than any other. However, the literature reveals that there still exists no consensus on a credible approach or approaches for the design of such systems, despite numerous documented efforts. Current approaches to the construction of ITSs leave much to be desired. Consequently, existing ITSs in the domain suffer from a considerable number of shortcomings which render them 'unintelligent'. The thesis examines some of the reasons why this is the case. Following a critical review of existing ITSs in the domain, and some pilot studies, an alternative approach to their construction is proposed (the 'iterative-style' approach); this supports an iterative style, and also improves on at least some of the shortcomings of existing approaches. The thesis also presents an ITS for fractions which has been developed using this approach, and which has been evaluated in various ways. It has, demonstrably, improved on many of the limitations of existing ITSs; furthermore, it has been shown to be largely 'intelligent', at least more so than current tutors for the domain. Perhaps more significantly, the tutor has also been evaluated against real students with, so far, very encouraging results. The thesis thus concludes that the novel iterative-style approach is a more credible approach to the construction of ITSs in mathematics than existing techniques.

An advanced real-time predictive maintenance framework for large scale machine systems

This thesis introduces and develops a novel real-time predictive maintenance system to estimate the machine system parameters using the motion current signature. Recently, motion current signature analysis has been addressed as an alternative to the use of sensors for monitoring internal faults of a motor. A maintenance system based upon the analysis of motion current signature avoids the need for the implementation and maintenance of expensive motion sensing technology. By developing nonlinear dynamical analysis for motion current signature, the research described in this thesis implements a novel real-time predictive maintenance system for current and future manufacturing machine systems. A crucial concept underpinning this project is that the motion current signature contains infor­mation relating to the machine system parameters and that this information can be extracted using nonlinear mapping techniques, such as neural networks. Towards this end, a proof of con­cept procedure is performed, which substantiates this concept. A simulation model, TuneLearn, is developed to simulate the large amount of training data required by the neural network ap­proach. Statistical validation and verification of the model is performed to ascertain confidence in the simulated motion current signature. Validation experiment concludes that, although, the simulation model generates a good macro-dynamical mapping of the motion current signature, it fails to accurately map the micro-dynamical structure due to the lack of knowledge regarding performance of higher order and nonlinear factors, such as backlash and compliance. Failure of the simulation model to determine the micro-dynamical structure suggests the pres­ence of nonlinearity in the motion current signature. This motivated us to perform surrogate data testing for nonlinearity in the motion current signature. Results confirm the presence of nonlinearity in the motion current signature, thereby, motivating the use of nonlinear tech­niques for further analysis. Outcomes of the experiment show that nonlinear noise reduction combined with the linear reverse algorithm offers precise machine system parameter estimation using the motion current signature for the implementation of the real-time predictive maintenance system. Finally, a linear reverse algorithm, BJEST, is developed and applied to the motion current signature to estimate the machine system parameters.

A systems approach to students' motivation and academic achievement

This research followed earlier work (reported in a thesis presented in 1970) on factors associated with the academic performance of a sample of technical college students, which recommended the further study of students' motivation. The technical college then became part of a polytechnic, but the courses chosen for the continuation of the research were all of a specifically vocational character. The approach was influenced by Angyal (1941) in seeking to relate symbolic processes to broader behaviour patterns within a systems framework. Forms of semantic differential were developed to obtain the students' responses to words representing various activities and various people both within and outside the academic environment. Also, a "!growth motivation questionnaire" was produced using ideas from self-actualisation, job satisfaction and expectancy theory and examination marks were recorded. From pre-coded responses to the growth motivation questionnaire, scores on a 'study satisfaction' factor were calculated, and subsamples of students were taken at the extremes of this scale. Wriitten responses from the same questionnaire and semantic differential factor scores showed contrasting patterns between the two subsamples. Interpretation of these patterns suggested a diversity of approach to academic work among the students which calls for greater flexibility in the educational system serving them.

The development, evaluation and use of freshly isolated renal proxinal tubule systems in the fischer rat

The investigation of renal pathophysiology and toxicology has traditionally been advanced by the development of increasingly defined and refined in vitro preparations. This study has sought to develop and evaluate various methods of producing pure samples of renal proximal tubules (PTs) from the Fischer rat. The introduction summarised the most common in vitro preparations together with the parameters used to monitor viability - particularly with regard to toxic events. The most prevalent isolation methods have involved the use of collagenase to produce dissociation of the cortex. However, the present study has shown that even the mildest collagenase treatment caused significant structural damage which resulted in a longevity of only 3hr in suspension. An alternative mechanical isolation technique has been developed in this study that consists of perfusion loading the renal glomeruli with Fe304 followed by disruption of the cortex by homogenisation and sequential sieving. The glomeruli are removed magnetically and the PTs then harvested by a 64μM sieve. PTs isolated in this way showed a vastly superior structural preservation over their collagenase isolated counterparts; also oxygen consumption and enzyme leakage measurements showed a longevity in excess of 6hr when incubated in a very basic medium. Attempts were then made to measure the cytosolic calcium levels in both mechanical and collagenase isolated PTs using the fluorescent calcium indicator Fura. However results were inconclusive due to significant binding of the Fura to the external PT surfaces. In conclusion, PTs prepared by the present mechanical isolation technique exhibit superior preservation and longevity compared with even the mildest collagenase isolation technique and hence appear to offer potential advantages over collagenase isolation as an in vitro renal system.

The Application of Geographic Information Systems to climate change & land evaluation : a study of the effects of climate change upon crop productivity in a sub-tropical environment

This research investigates the contribution that Geographic Information Systems (GIS) can make to the land suitability process used to determine the effects of a climate change scenario. The research is intended to redress the severe under representation of Developing countries within the literature examining the impacts of climatic change upon crop productivity. The methodology adopts some of the Intergovernmental Panel on Climate Change (IPCC) estimates for regional climate variations, based upon General Circulation Model predictions (GCMs) and applies them to a baseline climate for Bangladesh. Utilising the United Nations Food & Agricultural Organisation's Agro-ecological Zones land suitability methodology and crop yield model, the effects of the scenario upon agricultural productivity on 14 crops are determined. A Geographic Information System (IDRISI) is adopted in order to facilitate the methodology, in conjunction with a specially designed spreadsheet, used to determine the yield and suitability rating for each crop. A simple optimisation routine using the GIS is incorporated to provide an indication of the 'maximum theoretical' yield available to the country, should the most calorifically significant crops be cultivated on each land unit both before and after the climate change scenario. This routine will provide an estimate of the theoretical population supporting capacity of the country, both now and in the future, to assist with planning strategies and research. The research evaluates the utility of this alternative GIS based methodology for the land evaluation process and determines the relative changes in crop yields that may result from changes in temperature, photosynthesis and flooding hazard frequency. In summary, the combination of a GIS and a spreadsheet was successful, the yield prediction model indicates that the application of the climate change scenario will have a deleterious effect upon the yields of the study crops. Any yield reductions will have severe implications for agricultural practices. The optimisation routine suggests that the 'theoretical maximum' population supporting capacity is well in excess of current and future population figures. If this agricultural potential could be realised however, it may provide some amelioration from the effects of climate change.