Phagocyte oxidation of phospholipids: comparison of hydroperoxide, chlorohydrin and epoxyisoprostane formation by LC-MS

Phagocytic cells produce a variety of oxidants as part of the immune defence, which react readily both with proteins and lipids, and could contribute to the oxidation of low density lipoprotein in atherosclerosis. We have investigated the oxidation of phospholipid vesicles by isolated human polymorphonuclear and mononuclear leukocytes, to provide a model of lipid oxidation in the absence of competing protein. PMA-stimulated cells were incubated with phospholipid vesicles contammg dipalmitoyl phosphatidylcholine (DPPC), palmitoyl-arachidonoyl phosphatidylcholine (PAPC), and stearoyl-oleoyl phosphatidylcholine (SOPC), before extraction of the lipids for analysis by HPLC coupled to electrospray mass spectrometry. In this system, oxidized phosphatidylcholines elute earlier than the native lipids owing to their decreased hydrophobicity, and can be identified according to their molecular mass. The formation of monohydroperoxides of P APC was observed routinely, together with low levels of hydroxides, but no chlorohydrin derivatives of P APC or SOPC were detected. However, the major oxidized product occurred at 828 m/z, and was identified as I-palmitoyl-2-(5,6-epoxyisoprostane E2)-sn-glycero-3-phosphocholine. These results show that phagocytes triggered by PMA cause oxidative damage to lipids predominantly by free radical mechanisms, and that electrophilic addition involving HOCl is not a major mechanism of attack. The contribution of myeloperoxidase and metal ions to the oxidation process is currently being investigated, and preliminary data suggest that myeloperoxidase-derived oxidants are responsible for the epoxyisoprostane phospholipid formation. The identification of an epoxyisoprostane phospholipid as the major product following phagocyte-induced phospholipid oxidation is novel and has implications for phagocyte involvement in atherogenesis.

Effect of contact surfaces on the thermal and photoxidation of dehydrated castor oil

The effect of stainless steel, glass, zirconium and titanium enamel surfaces on the thermal and photooxidative toughening mechanism of dehydrated castor oil films deposited on these surfaces was investigated using different analytical and spectroscopic methods. The conjugated and non-conjugated double bonds were identified and quantified using both Raman spectroscopy and 1D and 2D NMR spectroscopy. The disappearance of the double bonds in thermally oxidised oil-on-surface films was shown to be concomitant with the formation of hydroperoxides (determined by iodometric titration). The type of the surface had a major effect on the rate of thermal oxidation of the oil, but all of the surfaces examined had resulted in a significantly higher rate of oxidation compared to that of the neat oil. The highest effect was exhibited by the stainless steel surface followed by zirconium enamel, titanium enamel and glass. The rate of thermal oxidation of the oil-on-steel surface (at 100 °C, based on peroxide values) was more than five times faster than that of oil-on-glass and more than 21 times faster than the neat oil when compared under similar thermal oxidative conditions. The rate of photooxidation at 60 °C of oil-on-steel films was found to be about one and half times faster than their rate of thermal oxidation at the same temperature. Results from absorbance reflectance infrared microscopy with line scans taken across the depth of thermally oxidised oil-on-steel films suggest that the thermal oxidative toughening mechanism of the oil occurs by two different reaction pathways with the film outermost layers, i.e. furthest away from the steel surface, oxidising through a traditional free radical oxidation process involving the formation of various oxygenated products formed from the decomposition of allylic hydroperoxides, whereas, in the deeper layers closer to the steel surface, crosslinking reactions predominate.

Polyunsaturated fatty acid oxidation in Alzheimer’s disease.

Alzheimer’s disease is a neurodegenerative disorder which has been characterised with genetic (apolipoproteins), protein (ß-amyloid and tau) and lipid oxidation/metabolism alterations in its pathogenesis. In conjunction with the Dementia Research Group, Bristol University, investigation into genetic, protein and lipid oxidation in Alzheimer’s disease was conducted. A large sample cohort using the double-blind criteria, along with various clinical and chemical data sets were used to improve the statistical analysis and therefore the strength of this particular study. Bristol University completed genetic and protein analysis with lipid oxidation assays performed at Aston University. Lipid oxidation is a complex process that creates various biomarkers, from transient intermediates, to short carbon chain products and cyclic ring structures. Quantification of these products was performed on lipid extracts of donated clinical diseased and non-diseased frontal and temporal brain regions, from the Brain Bank within Frenchay Hospital. The initial unoxidised fatty acids, first transient oxidation intermediates the conjugated dienes and lipid hydroperoxides, the endpoint aldehyde biomarkers and finally the cyclic isoprostanes and neuroprostanes were determined to investigate lipid oxidation in Alzheimer’s. Antioxidant levels were also investigated to observe the effect of oxidation on the defence pathways. Assays utilised in this analysis included; fatty acid composition by GC-FID, conjugated diene levels by HPLC-UV and UV-spec, lipid hydroperoxide levels by FOX, aldehyde content by TBARs, antioxidant status by TEAC and finally isoprostane and neuroprostane quantification using a newly developed EI-MS method. This method involved the SIM of specific ions from F-ring isoprostane and neuroprostane fragmentation, which enabled EI-MS to be used for their quantification. Analyses demonstrated that there was no significant difference between control and Alzheimer samples across all the oxidation biomarkers for both brain regions. Antioxidants were the only marker that showed a clear variance; with Alzheimer samples having higher levels than the age matched controls. This unique finding is supported with the observed lower levels of lipid oxidation biomarkers in Alzheimer brain region samples. The increased antioxidant levels indicate protection against oxidation which may be a host response to counteract the oxidative pathways, but this requires further investigation. In terms of lipid oxidation, no definitive markers or target site for therapeutic intervention have been revealed. This study concludes that dietary supplementation of omega-3 fatty acids or antioxidants would most likely be ineffective against Alzheimer disease, although it may support improvement in other areas of general health.

Oxidation of organic compounds in molten salts

The objective of this research was to investigate the oxidation of organic compounds in molten alkali metal hydroxides containing manganates. It has been shown that controlled oxidation can be readily achieved with high specificity to give products in high yield with very short reaction times. The concurrent changes in the melt were monitored using a vibrating platinum indicator electrode with a quazi-reference electrode which was successfully developed for use in molten (Na-K)OH eutectic at 523K. Henry's Law constants for water in the molten eutectic system (Na-K)OH have been measured and used to calculate the water concentration in the melt. The electrochemistry of manganates in molten (Na-K)OH eutectic at 523K has been studied using the vibrating platinum electrode, and the existence of the species Mn(II), Mn(II!), Mn(IV), Mn(V) and Mn(VI) in such melts has been investigated at various water concentrations. The half-wave potentials of the voltammetric waves were measured versus the cathodic limit of the melt. The stability of Mn(V) or Mn(VI) in the melt was achieved by varying the water concentration. A range of organic chemicals has been passed through molten (Na-K)OH at 523K and the reactions of these chemicals with the melt have been studied. The same organics were then passed through molten (Na-K)OH containing stabilized Mn(V) or Mn{VI) without violent reaction. Methanol, allyl alcohol, propane 1, 2 diol, I-heptene and acetone were oxidized by Mn(V) and Mn(VI). Ethanol was only oxidized by Mn(VI), isopropanol and benzyl alcohol were only oxidized by Mn(V). Npropanol, butanol, 2 methyl propan-2-ol, n-hexane, n-heptane toluene and cyclohexane were unchanged by both Mn(V) and Mn(VI). Detailed experiments have been performed on the reactions of ethanol, iso-propanol and methanol in molten (Na-K)OH containing stabilized Mrt(V) or Mn(VI), and reaction mechanisms have been postulated. Ethanol and iso-propanol were oxidized to acetaldehyde and acetone respectively with a potential for useful chemical process. The oxidation of methanol could be developed as a basis for an industrial methanol disposal process.

A genetic algorithm to optimise the component placement process in the PCB assembly

In printed circuit board (PCB) assembly, the efficiency of the component placement process is dependent on two interrelated issues: the sequence of component placement, that is, the component sequencing problem, and the assignment of component types to feeders of the placement machine, that is, the feeder arrangement problem. In cases where some components with the same type are assigned to more than one feeder, the component retrieval problem should also be considered. Due to their inseparable relationship, a hybrid genetic algorithm is adopted to solve these three problems simultaneously for a type of PCB placement machines called the sequential pick-and-place (PAP) machine in this paper. The objective is to minimise the total distance travelled by the placement head for assembling all components on a PCB. Besides, the algorithm is compared with the methods proposed by other researchers in order to examine its effectiveness and efficiency.

Advanced liquid-liquid extraction : studies in a laboratory mixer-settler

A ten stage laboratory mixer-settler has been designed, constructed and operated with efficiencies up to 90%. The phase equilibrium data of the system acetic acid-toluene-water at different temperatures has been determined and correlated. Trials for prediction of these data have been investigated and a good agreement between the experimental data and the predictions obtained by the NRTL equation have been found. Extraction processes have been analysed. A model for determination of the time needed for a countercurrent stage-wise process to come to steady state has been derived. The experimental data was in reasonable agreement with this model. The discrete maximum principle has been applied to optimize the countercurrent extraction process and proved to be highly successful in predicting the optimum operating conditions which were confirmed by the experimental results. The temperature has proved to be a prosolvent for mass transfer in both directions but the temperature profile functioned as an anti solvent.

Molecularly imprinted polymers in the drug discovery process

Since molecularly imprinted polymers (MIPs) are designed to have a memory for their molecular templates it is easy to draw parallels with the affinity between biological receptors and their substrates. Could MIPs take the place of natural receptors in the selection of potential drug molecules from synthetic compound libraries? To answer that question this review discusses the results of MIP studies which attempt to emulate natural receptors. In addition the possible use of MIPs to guide a compound library synthesis towards a desired biological activity is highlighted. © 2005 Elsevier B.V. All rights reserved.

Advanced manufacturing technology adoption in developing countries:the role of buyer-supplier relationships

Purpose – Developing countries are heavily dependent on the resources and commitment of foreign providers to ensure successful adoption of advanced manufacturing technology (AMT). The purpose of this paper is to describe the important role of buyer-supplier relationships (BSRs) in the process of technology selection, acquisition and implementation. Design/methodology/approach – A survey of 147 Malaysian manufacturing firms is the main instrument used in the research investigations and data analysis is carried out by the structured equation modelling (SEM) technique. In particular, the authors examine the impact on performance of different patterns of relationship between technology buyers and suppliers. Findings – Although the majority of the firms reported improvements in their performance since the acquisition of AMT, closer investigation reveals that those demonstrating a closer relationship with their suppliers are more likely to achieve higher levels of technology and implementation performance (IP) than those that do not. Research limitations/implications – The paper only assesses the strength of BSR from the buyers' perspective and they may have limited experience of acquisition, whereas suppliers may have more experience of selling AMT. Also, the research is undertaken in Malaysia and the findings may be different in other countries, especially where the technology being acquired is not imported but sourced locally. Practical implications – The findings relating to BSR, technology acquisition and IP have important implications both for customers and supplier firms as well as for industrial policy makers in developing countries. Originality/value – The result of the research provides useful insights that are especially pertinent to an improved understanding of BSRs in the procurement of capital equipment, about which the current research literature is limited.

An application of decision process modelling to manufacturing system design

As levels of investment in advanced manufacturing systems increase, effective project management becomes ever more critical. This paper demonstrates how the model proposed by Mintzberg, Raisinghani and Theoret in 1976, which structures complicated strategic decision processes, can be applied to the design of new production systems for both descriptive and analytical research purposes. This paper sets a detailed case study concerning the design and development of an advanced manufacturing system within the Mintzberg decision model and so breaks down the decision sequence into constituent parts. It thus shows how a structured model can provide a framework for the researcher who wishes to study decision episodes in the design of manufacturing facilities in greater depth.

A discussion of ethnographic research methods and their relevance for the translation process

In recent years, technologically advanced methodologies such as Translog have gained a lot of ground in translation process research. However, in this paper it will be argued that quantitative research methods can be supplemented by ethnographic qualitative ones so as to enhance our understanding of what underlies the translation process. Although translation studies scholars have sometimes applied an ethnographic approach to the study of translation, this paper offers a different perspective and considers the potential of ethnographic research methods for tapping cognitive and behavioural aspects of the translation process. A number of ethnographic principles are discussed and it is argued that process researchers aiming to understand translators’ perspectives and intentions, how these shape their behaviours, as well as how translators reflect on the situations they face and how they see themselves, would undoubtedly benefit from adopting an ethnographic framework for their studies on translation processes.

Intermediate pyrolysis:a sustainable biomass-to-energy concept-biothermal valorisation of biomass (BtVB) process

Wastewater treatment coupled with energy crop cultivation provides an attractive source of cheap feedstock. This study reviews an advanced, closed-loop bioenergy conversion process [biothermal valorisation of biomass (BtVB)], in which pyroformer is coupled to a gasifier. BtVB process was developed at European Bioenergy Research Institute (EBRI), Aston University, UK and demonstrates an improved method for thermal conversion of ash-rich biomass.

Buyer-supplier relationships in advanced manufacturing technology acquisition and implementation : a study in Malaysia

This thesis reports the results of research into the connections between transaction attributes and buyer-supplier relationships (BSR) in advanced manufacturing technology (AMT) acquisitions and implementation. It also examines the impact of the different patterns of BSR on performance. Specifically, it addresses the issues of how the three transaction attributes; namely level of complexity, level of asset specificity, and level of uncertainty, can affect the relationships between the technology buyer and suppler in AMT acquisition and implementation, and then to see the impact of different patterns of BSR on the two aspect of performance; namely technology and implementation performance. In understanding the pohenomena, the study mainly draws on and integrates the literature of transaction cost economics theory,buyer-supplier relationships and advanced manufacturing technology as a basis of theoretical framework and hypotheses development.data were gathered through a questionnaire survey with 147 responses and seven semi-structured interviews of manufacturing firms in Malaysia. Quantitative data were analysed mainly using the AMOS (Analysis of Moment Structure) package for structural equation modeling and SPSS (Statistical Package for Social Science) for analysis of variance (ANOVA). Data from interview sessions were used to develop a case study with the intention of providing a richer and deeper understanding on the subject under investigation and to offer triangulation in the research process. he results of the questionnaire survey indicate that the higher the level of technological specificity and uncertainty, the more firms are likely to engage in a closer relationship with technology suppliers.However, the complexity of the technology being implemented is associated with BSR only because it is associated with the level of uncertainty that has direct impact upon BSR.The analysis also provides strong support for the premise that developing strong BSR could lead to an improved performance. However, with high levels of transaction attribute, implementation performance suffers more when firms have weak relationships with technology suppliers than with moderate and low levels of transaction attributes. The implications of the study are offered for both the academic and practitioner audience. The thesis closes with reports on its limitations and suggestions for further research that would address some of these limitations.

The process of strategic change:a management perspective

This thesis is concerned with the management processes concerned with complex strategic decision in organisations. The research has sought to explore these processes by taking as its focus the reconstruction of decision processes a) on the basis of an historical study of an industry and in particular a major company in that industry; and b) the perception and understanding of strategic decision processes and change by managers involved in companies in that industry. The main body of analysis and theoretical contributions arise from the detailed analysis of extended depth interviews with managers carried out in 1980 and 1983 which trace thirteen years of the strategic development of a firm. In so doing, extensive use is made of verbatim accounts by managers of events and their interpretation of events. This is then compared with data gathered from.similar interviews with managers of two other companies and examined in the light of existing research and theory in the field. The thesis both provides a detailed insight into the processes associated with the identification and resolution of complex strategic issues and also generates a body of theory concerning the mechanisms by which strategic decisions and the processes of strategic change are interwoven with the cultural and political fabric of organisations. The thesis is divided into four parts. The first part deals with the background to the research, provid1ng a fuller summary of the purpose, structure and content of the thesis and a discussion of relevant previous research and the methodology employed herein. The second part mainly provides case studies of the industry and the main company studied. The third part is a detailed presentation and analysis of data. The fourth part is a synthesis of the findings and consolidation of the theoretical interpretation advanced in the thesis.