The casing layer in the culture of Agaricus bisporus, the cultivated mushroom

The casing layer is an essential component of the system employed in the culture of Agaricus bisporus. The literature appropriate to the casing layer is fully reviewed, including aspects relating to fructification and morphogenesis in A.bisporus, together with an appraisal of the various media employed, their properties and functions, and the commercial significance of the casing layer. Equipment is described for use in experiments in mushroom culture, based on a scaled-down version of normal growing technique, allowing the analysis of both weights and number of fruitbodies forming, which was useful in assessing the effects of different casing treatments. The basic steps in the production of fruitbodies in A.bisporus.are described, including a photographic study of the colonisation of casing and fructification. Various alterations to the physical structure of peat/chalk casing mixtures were found to have an effect on fructification; those causing an opening-out of the casing structure tended to give better yields, especially in the early stages of production. It was shown that, in order to obtain greater yield through casing amendment, fructification must be stimulated, giving increased numbers of fruitbodies, disproportionate to their total weight and consequently of lower mean weight. A synthetic casing medium based on the light glass-like mineral, perlite, was developed. The best formula obtained was -.1 part perlite: 1 part montmorillonite clay (by weight): 3 parts 0.01% glucose solution. Perlite/montmorillonite casing could be improved by adding compost colonised by mycelium of A.bisporus, or adding a peat-chalk casing extract. Perlite was also found to be suitable for admixture with the standard casing medium and a mixture of equal parts by volume performed as well as the peat/chalk casing normally used.

A techno-economic study of the recycling of mixed plastics to useful products

The techno-economic implications of recycling the components of mixed plastics waste have been studied in a two-part investigation: (a) An economic survey of the prospects for plastics recycling, the plastics waste arisings from retailing, building, automotive, light engineering and chemical industries have been surveyed by mans of questionnaires and interviews. This was partially successful and indicated that very considerable quantities of relatively clean plastics packaging was available in major department chains and household stores. The possibility of devising collection systems for such sources, which do not lead to any extra cost, have been suggested. However, the household collection of plastics waste has been found to be uneconomic due to high cost of collection, transportation and lack of markets for the end products. (b) In a technical study of blends of PE/PP and PE/PS which are found in admixture in waste plastics, it has been shown that they exhibit poor mechanical properties due to incompatibility. Consequently reprocessing of such unsegregated blends results in products of little technological value. The inclusion of some commercial block and graft copolymers which behave as solid phase dispersants (SPES) increase the toughness of the blends (e.g. EPDM in PE/PP blend and SBS in PE/PS blend). Also, EPDM is found to be very effective for improving the toughness of single component polypropylene. However, the improved Technical properties of such blends have been accompanied by a fast rate of photo-oxidation and loss of toughness due to the presence of unsaturation in SPD's. The change in mechanical properties occurring during oven ageing and ultra-violet light accelerated weathering of these binary and ternary blends was followed by a viscoelastonetric technique (Rheovibron) over 9,, wide range of temperatures, impact resistance at room temperature (20-41'G) and changes in functional groups (i.e. carbonyl and trans-1,4-polybutadiene). Also the heat and light stability of single and mixed plastics to which thiol antioxidants were bound to SPE1 segment have been studied and compared with conventional antioxidants. The long-term performance of the mixed plastics containing SPE1 have been improved significantly by the use of conventional and bound antioxidants. It is concluded that an estimated amount of 30000 tonnes/year of plastics waste is available from department chains and household stores which can be converted to useful end products. This justifies pilot-experiments in collaboration with supermarkets, recyclers and converters by use of low cost SPD's and additives designed to make the materials more compatible.