A study of thermodynamic characteristics and predictive computer modelling of an air to water heat pump system

A study on heat pump thermodynamic characteristics has been made in the laboratory on a specially designed and instrumented air to water heat pump system. The design, using refrigerant R12, was based on the requirement to produce domestic hot water at a temperature of about 50 °C and was assembled in the laboratory. All the experimental data were fed to a microcomputer and stored on disk automatically from appropriate transducers via amplifier and 16 channel analogue to digital converters. The measurements taken were R12 pressures and temperatures, water and R12 mass flow rates, air speed, fan and compressor input powers, water and air inlet and outlet temperatures, wet and dry bulb temperatures. The time interval between the observations could be varied. The results showed, as expected, that the COP was higher at higher air inlet temperatures and at lower hot water output temperatures. The optimum air speed was found to be at a speed when the fan input power was about 4% of the condenser heat output. It was also found that the hot water can be produced at a temperature higher than the appropriate R12 condensing temperature corresponding to condensing pressure. This was achieved by condenser design to take advantage of discharge superheat and by further heating the water using heat recovery from the compressor. Of the input power to the compressor, typically about 85% was transferred to the refrigerant, 50 % by the compression work and 35% due to the heating of the refrigerant by the cylinder wall, and the remaining 15% (of the input power) was rejected to the cooling medium. The evaporator effectiveness was found to be about 75% and sensitive to the air speed. Using the data collected, a steady state computer model was developed. For given input conditions s air inlet temperature, air speed, the degree of suction superheat , water inlet and outlet temperatures; the model is capable of predicting the refrigerant cycle, compressor efficiency, evaporator effectiveness, condenser water flow rate and system Cop.

Improved production of industrially relevant recombinant proteins: application of multi-factorial design of experiments and scalable process modelling

The work described in this thesis focuses on the use of a design-of-experiments approach in a multi-well mini-bioreactor to enable the rapid establishments of high yielding production phase conditions in yeast, which is an increasingly popular host system in both academic and industrial laboratories. Using green fluorescent protein secreted from the yeast, Pichia pastoris, a scalable predictive model of protein yield per cell was derived from 13 sets of conditions each with three factors (temperature, pH and dissolved oxygen) at 3 levels and was directly transferable to a 7 L bioreactor. This was in clear contrast to the situation in shake flasks, where the process parameters cannot be tightly controlled. By further optimisating both the accumulation of cell density in batch and improving the fed-batch induction regime, additional yield improvement was found to be additive to the per cell yield of the model. A separate study also demonstrated that improving biomass improved product yield in a second yeast species, Saccharomyces cerevisiae. Investigations of cell wall hydrophobicity in high cell density P. pastoris cultures indicated that cell wall hydrophobin (protein) compositional changes with growth phase becoming more hydrophobic in log growth than in lag or stationary phases. This is possibly due to an increased occurrence of proteins associated with cell division. Finally, the modelling approach was validated in mammalian cells, showing its flexibility and robustness. In summary, the strategy presented in this thesis has the benefit of reducing process development time in recombinant protein production, directly from bench to bioreactor.

The modelling of energy efficient drying for DSM (BL)

This thesis investigates the modelling of drying processes for the promotion of market-led Demand Side Management (DSM) as applied to the UK Public Electricity Suppliers. A review of DSM in the electricity supply industry is provided, together with a discussion of the relevant drivers supporting market-led DSM and energy services (ES). The potential opportunities for ES in a fully deregulated energy market are outlined. It is suggested that targeted industrial sector energy efficiency schemes offer significant opportunity for long term customer and supplier benefit. On a process level, industrial drying is highlighted as offering significant scope for the application of energy services. Drying is an energy-intensive process used widely throughout industry. The results of an energy survey suggest that 17.7 per cent of total UK industrial energy use derives from drying processes. Comparison with published work indicates that energy use for drying shows an increasing trend against a background of reducing overall industrial energy use. Airless drying is highlighted as offering potential energy saving and production benefits to industry. To this end, a comprehensive review of the novel airless drying technology and its background theory is made. Advantages and disadvantages of airless operation are defined and the limited market penetration of airless drying is identified, as are the key opportunities for energy saving. Limited literature has been found which details the modelling of energy use for airless drying. A review of drying theory and previous modelling work is made in an attempt to model energy consumption for drying processes. The history of drying models is presented as well as a discussion of the different approaches taken and their relative merits. The viability of deriving energy use from empirical drying data is examined. Adaptive neuro fuzzy inference systems (ANFIS) are successfully applied to the modelling of drying rates for 3 drying technologies, namely convective air, heat pump and airless drying. The ANFIS systems are then integrated into a novel energy services model for the prediction of relative drying times, energy cost and atmospheric carbon dioxide emission levels. The author believes that this work constitutes the first to use fuzzy systems for the modelling of drying performance as an energy services approach to DSM. To gain an insight into the 'real world' use of energy for drying, this thesis presents a unique first-order energy audit of every ceramic sanitaryware manufacturing site in the UK. Previously unknown patterns of energy use are highlighted. Supplementary comments on the timing and use of drying systems are also made. The limitations of such large scope energy surveys are discussed.

Drying processess in the United Kingdom:assessment of industrial energy utilisation and efficiency of drying systems and the modelling of drying characters using neural networks (BL)

Drying is an important unit operation in process industry. Results have suggested that the energy used for drying has increased from 12% in 1978 to 18% of the total energy used in 1990. A literature survey of previous studies regarding overall drying energy consumption has demonstrated that there is little continuity of methods and energy trends could not be established. In the ceramics, timber and paper industrial sectors specific energy consumption and energy trends have been investigated by auditing drying equipment. Ceramic products examined have included tableware, tiles, sanitaryware, electrical ceramics, plasterboard, refractories, bricks and abrasives. Data from industry has shown that drying energy has not varied significantly in the ceramics sector over the last decade, representing about 31% of the total energy consumed. Information from the timber industry has established that radical changes have occurred over the last 20 years, both in terms of equipment and energy utilisation. The energy efficiency of hardwood drying has improved by 15% since the 1970s, although no significant savings have been realised for softwood. A survey estimating the energy efficiency and operating characteristics of 192 paper dryer sections has been conducted. Drying energy was found to increase to nearly 60% of the total energy used in the early 1980s, but has fallen over the last decade, representing 23% of the total in 1993. These results have demonstrated that effective energy saving measures, such as improved pressing and heat recovery, have been successfully implemented since the 1970s. Artificial neural networks have successfully been applied to model process characteristics of microwave and convective drying of paper coated gypsum cove. Parameters modelled have included product moisture loss, core gypsum temperature and quality factors relating to paper burning and bubbling defects. Evaluation of thermal and dielectric properties have highlighted gypsum's heat sensitive characteristics in convective and electromagnetic regimes. Modelling experimental data has shown that the networks were capable of simulating drying process characteristics to a high degree of accuracy. Product weight and temperature were predicted to within 0.5% and 5C of the target data respectively. Furthermore, it was demonstrated that the underlying properties of the data could be predicted through a high level of input noise.

The association between presenteeism and engagement of National Health Service staff

Objective: Although several studies have demonstrated a relationship between staff engagement and health and wellbeing, none has analysed the association with presenteeism in the National Health Service (NHS) context. Our aim is to determine whether there is a relationship between presenteeism and staff engagement. Methods: A hierarchical logistic multilevel modelling of cross-sectional data from the NHS staff survey (2009) was conducted. We controlled for a range of demographic and socioeconomic background variables, including ethnic group, gender, age and occupational group. The sample was 156,951 respondents across all 390 English NHS trusts, each providing a random sample of employees. Engagement was measured using three facets: motivation, advocacy and involvement, which were also used in a composite score. Results: Therewas a low-to-moderate negative correlation between presenteeismand staff engagement: odds ratio 0.42 (95% confidence interval [CI] 0.42-0.43) for overall staff engagement and 0.53 (95% CI 0.52-0.54) for staff advocacy of the trust; 0.53 (95% CI 0.52-0.54) for motivation and 0.50 (95% CI 0.49-0.51) for involvement. Conclusions: Putting pressure on health-care staff to come to work when unwell is associated with poorer staff engagement with their jobs. © The Royal Society of Medicine Press Ltd 2011.

Developments in contact lens measurement:a comparative study of industry standard geometric inspection and optical coherence tomography

Purpose: The aim of this study was to compare a developmental optical coherence tomography (OCT) based contact lens inspection instrument to a widely used geometric inspection instrument (Optimec JCF), to establish the capability of a market focused OCT system. Methods: Measurements of 27 soft spherical contact lenses were made using the Optimec JCF and a new OCT based instrument, the Optimec is830. Twelve of the lenses analysed were specially commissioned from a traditional hydrogel (Contamac GM Advance 49%) and 12 from a silicone hydrogel (Contamac Definitive 65), each set with a range of back optic zone radius (BOZR) and centre thickness (CT) values. Three commercial lenses were also measured; CooperVision MyDay (Stenfilcon A) in −10D, −3D and +6D powers. Two measurements of BOZR, CT and total diameter were made for each lens in temperature controlled saline on both instruments. Results: The results showed that the is830 and JCF measurements were comparable, but that the is830 had a better repeatability coefficient for BOZR (0.065 mm compared to 0.151 mm) and CT (0.008 mm compared to 0.027 mm). Both instruments had similar results for total diameter (0.041 mm compared to 0.044 mm). Conclusions: The OCT based instrument assessed in this study is able to match and improve on the JCF instrument for the measurement of total diameter, back optic zone radius and centre thickness for soft contact lenses in temperature controlled saline.

Introduction: improving manufacturing performance through technology diffusion, implementation and management

The role of technology management in achieving improved manufacturing performance has been receiving increased attention as enterprises are becoming more exposed to competition from around the world. In the modern market for manufactured goods the demand is now for more product variety, better quality, shorter delivery and greater flexibility, while the financial and environmental cost of resources has become an urgent concern to manufacturing managers. This issue of the International Journal of Technology Management addresses the question of how the diffusion, implementation and management of technology can improve the performance of manufacturing industries. The authors come from a large number of different countries and their contributions cover a wide range of topics within this general theme. Some papers are conceptual, others report on research carried out in a range of different industries including steel production, iron founding, electronics, robotics, machinery, precision engineering, metal working and motor manufacture. In some cases they describe situations in specific countries. Several are based on presentations made at the UK Operations Management Association's Sixth International Conference held at Aston University at which the conference theme was 'Achieving Competitive Edge: Getting Ahead Through Technology and People'. The first two papers deal with questions of advanced manufacturing technology implementation and management. Firstly Beatty describes a three year longitudinal field study carried out in ten Canadian manufacturing companies using CADICAM and CIM systems. Her findings relate to speed of implementation, choice of system type, the role of individuals in implementation, organization and job design. This is followed by a paper by Bessant in which he argues that a more a strategic approach should be taken towards the management of technology in the 1990s and beyond. Also considered in this paper are the capabilities necessary in order to deploy advanced manufacturing technology as a strategic resource and the way such capabilities might be developed within the firm. These two papers, which deal largely with the implementation of hardware, are supplemented by Samson and Sohal's contribution in which they argue that a much wider perspective should be adopted based on a new approach to manufacturing strategy formulation. Technology transfer is the topic of the following two papers. Pohlen again takes the case of advanced manufacturing technology and reports on his research which considers the factors contributing to successful realisation of AMT transfer. The paper by Lee then provides a more detailed account of technology transfer in the foundry industry. Using a case study based on a firm which has implemented a number of transferred innovations a model is illustrated in which the 'performance gap' can be identified and closed. The diffusion of technology is addressed in the next two papers. In the first of these, by Lowe and Sim, the managerial technologies of 'Just in Time' and 'Manufacturing Resource Planning' (or MRP 11) are examined. A study is described from which a number of factors are found to influence the adoption process including, rate of diffusion and size. Dahlin then considers the case of a specific item of hardware technology, the industrial robot. Her paper reviews the history of robot diffusion since the early 1960s and then tries to predict how the industry will develop in the future. The following two papers deal with the future of manufacturing in a more general sense. The future implementation of advanced manufacturing technology is the subject explored by de Haan and Peters who describe the results of their Dutch Delphi forecasting study conducted among a panel of experts including scientists, consultants, users and suppliers of AMT. Busby and Fan then consider a type of organisational model, 'the extended manufacturing enterprise', which would represent a distinct alternative pure market-led and command structures by exploiting the shared knowledge of suppliers and customers. The three country-based papers consider some strategic issues relating manufacturing technology. In a paper based on investigations conducted in China He, Liff and Steward report their findings from strategy analyses carried out in the steel and watch industries with a view to assessing technology needs and organizational change requirements. This is followed by Tang and Nam's paper which examines the case of machinery industry in Korea and its emerging importance as a key sector in the Korean economy. In his paper which focuses on Venezuela, Ernst then considers the particular problem of how this country can address the problem of falling oil revenues. He sees manufacturing as being an important contributor to Venezuela's future economy and proposes a means whereby government and private enterprise can co-operate in development of the manufacturing sector. The last six papers all deal with specific topics relating to the management manufacturing. Firstly Youssef looks at the question of manufacturing flexibility, introducing and testing a conceptual model that relates computer based technologies flexibility. Dangerfield's paper which follows is based on research conducted in the steel industry. He considers the question of scale and proposes a modelling approach determining the plant configuration necessary to meet market demand. Engstrom presents the results of a detailed investigation into the need for reorganising material flow where group assembly of products has been adopted. Sherwood, Guerrier and Dale then report the findings of a study into the effectiveness of Quality Circle implementation. Stillwagon and Burns, consider how manufacturing competitiveness can be improved individual firms by describing how the application of 'human performance engineering' can be used to motivate individual performance as well as to integrate organizational goals. Finally Sohal, Lewis and Samson describe, using a case study example, how just-in-time control can be applied within the context of computer numerically controlled flexible machining lines. The papers in this issue of the International Journal of Technology Management cover a wide range of topics relating to the general question of improving manufacturing performance through the dissemination, implementation and management of technology. Although they differ markedly in content and approach, they have the collective aim addressing the concepts, principles and practices which provide a better understanding the technology of manufacturing and assist in achieving and maintaining a competitive edge.

A cross-national comparative study of the roles of men in contemporary France and Britain

The purpose of this thesis is to increase understanding and contribute to knowledge about the attitudes and behaviour of men in contemporary France and Britain. The thesis has three main aims: firstly, to provide the first cross-national comparison of French and British writing and research on the place of men in contemporary society; secondly, to identify similarities and differences in the roles of men in France and Britain; and thirdly, to determine to what extent and in what way such similarities and differences are linked to the social structures and cultural background of each country. The thesis focuses on two main facets of the male experience: the relationship between men and women and the interaction between fathers and their children. Men's attitudes and behaviour are examined in relation to issues such as the division of household tasks and child care within the family, parental roles, female employment, role reversal, gender stereotyping and changes towards a new image of masculinity in society. Particular consideration is given to differences in governmental attitudes in France and Britain towards the introduction of family policy measures for men as fathers. The thesis ends with a discussion of legislative, social and educational measures which could be introduced in France and Britain in order to promote greater flexibility in men's roles and consequently improve gender equality in each country. The data analysed in the thesis are derived from a questionnaire-based empirical study involving 101 men in Britain and seventy-five men in France. The respondents' experience of and attitudes towards their roles in society are analysed and interpreted in the light of profile data relating to their family circumstances and with reference to knowledge about the broader socio-cultural context.

Organizational and textual structuring of radio news discourse in English and Arabic.

The present work studies the overall structuring of radio news discourse via investigating three metatextual/interactive functions: (1) Discourse Organizing Elements (DOEs), (2) Attribution and (3) Sentential and Nominal Background Information (SBI & NBI). An extended corpus of about 73,000 words from BBC and Radio Damascus news is used to study DOEs and a restricted corpus of 38,000 words for Attribution and S & NBI. A situational approach is adopted to assess the influence of factors such as medium and audience on these functions and their frequence. It is found that: (1) DOEs are organizational and their frequency is determined by length of text; (2) Attribution Function in accordance with the editor's strategy and its frequency is audience sensitive; and (3) BI provides background information and is determined by audience and news topics. Secondly, the salient grammatical elements in DOEs are discourse deictic demonstratives, address pronouns and nouns referring to `the news'. Attribution is realized in reporting/reported clauses, and BI in a sentence, a clause or a nominal group. Thirdly, DOEs establish a hierarchy of (1) news, (2) summary/expansion and (3) item: including topic introduction and details. While Attribution is generally, and SBI solely, a function of detailing, NBI and proper names are generally a function of summary and topic introduction. Being primarily addressed to audience and referring metatextually, the functions investigated support Sinclair's interactive and autonomous planes of discourse. They also shed light on the part(s) of the linguistic system which realize the metatextual/interactive function. Strictly, `discourse structure' inevitably involves a rank-scale; but news discourse also shows a convention of item `listing'. Hence only within the boundary of variety (ultimately interpreted across language and in its situation) can textual functions and discourse structure be studied. Finally, interlingual variety study provides invaluable insights into a level of translation that goes beyond matching grammatical systems or situational factors, an interpretive level which has to be described in linguistic analysis of translation data.

A study in Britain and France of the development of cross-cultural in-house sales training using distance learning.

The thesis is concerned with cross-cultural distance learning in two countries: Great Britain and France. Taking the example of in-house sales training, it argues that it is possible to develop courses for use in two or more countries of differing culture and language. Two courses were developed by the researcher. Both were essentially print-based distance-learning courses designed to help salespeople achieve a better understanding of their customers. One used a quantitative, the other qualitative approach. One considered the concept of the return on investment and the other, for which a video support was also developed, considered the analysis of a customer's needs. Part 1 of the thesis considers differences in the training context between France and Britain followed by a review of the learning process with reference to distance learning. Part 2 looks at the choice of training medium course design and evaluation and sets out the methodology adopted, including problems encountered in this type of fieldwork. Part 3 analyses the data and draws conclusions from the findings, before offering a series of guidelines for those concerned with the development of cross-cultural in-house training courses. The results of the field tests on the two courses were analysed in relation to the socio-cultural, educational and experiential background of the learners as well as their preferred learning styles. The thesis argues that it is possible to develop effective in-house sales training courses to be used in two cultures and identifies key considerations which need to be taken into account when carrying out this type of work.

Development of multiphase and multiscale mathematical models for thermal spray process

High velocity oxyfuel (HVOF) thermal spraying is one of the most significant developments in the thermal spray industry since the development of the original plasma spray technique. The first investigation deals with the combustion and discrete particle models within the general purpose commercial CFD code FLUENT to solve the combustion of kerosene and couple the motion of fuel droplets with the gas flow dynamics in a Lagrangian fashion. The effects of liquid fuel droplets on the thermodynamics of the combusting gas flow are examined thoroughly showing that combustion process of kerosene is independent on the initial fuel droplet sizes. The second analysis copes with the full water cooling numerical model, which can assist on thermal performance optimisation or to determine the best method for heat removal without the cost of building physical prototypes. The numerical results indicate that the water flow rate and direction has noticeable influence on the cooling efficiency but no noticeable effect on the gas flow dynamics within the thermal spraying gun. The third investigation deals with the development and implementation of discrete phase particle models. The results indicate that most powder particles are not melted upon hitting the substrate to be coated. The oxidation model confirms that HVOF guns can produce metallic coating with low oxidation within the typical standing-off distance about 30cm. Physical properties such as porosity, microstructure, surface roughness and adhesion strength of coatings produced by droplet deposition in a thermal spray process are determined to a large extent by the dynamics of deformation and solidification of the particles impinging on the substrate. Therefore, is one of the objectives of this study to present a complete numerical model of droplet impact and solidification. The modelling results show that solidification of droplets is significantly affected by the thermal contact resistance/substrate surface roughness.

Background levels of urban land contamination

The research work reported in this thesis is concerned with the development and application of an urban scale sampling methodology for measuring and assessing background levels of heavy metal soil contamination in large and varied urban areas. The policy context of the work is broadly the environmental health problems posed by contaminated land and their implications for urban development planning. Within this wider policy context, the emphasis in the research has been placed on issues, related to the determination and application of 'guidelines' for assessing the significance of contaminated land for environmental planning. In concentrating on background levels of land contamination, the research responds to the need for additional techniques which address both the problems of measuring soil contamination at the urban scale and which are also capable of providing detailed information for use in the assessment of contaminated sites. Therefore, a key component of the work has been the development of a land-use based sampling framework for generating spatially comprehensive data on heavy metals in soil. The utility of the information output of the sampling method is demonstrated in two alternative ways. Firstly, it has been used to map the existing pattern of typical levels of heavy metals in urban soils. Secondly, it can be used to generate both generalised data in the form of 'reference levels' from which the overall significance of .background contamination may be assessed and detailed data, termed 'normal limit levels' for use in the assessment of site specific investigation data. The fieldwork was conducted in the West Midlands Metropolitan County and surface soil has been sampled and analysed for a measure of plant-available' and 'total' lead cadmium, copper and zinc. The research contrasts with much of the previous work on contaminated land which has generally concentrated on either the detailed investigation of individual sites suspected of being contaminated or the appraisal of land contamination resulting from specific point sources.

Diversity faultlines, shared objectives, and top management team performance

Faultline theory suggests that negative effects of team diversity are better understood by considering the influence of different dimensions of diversity in conjunction, rather than for each dimension separately. We develop and extend the social categorization analysis that lies at the heart of faultline theory to identify a factor that attenuates the negative influence of faultlines: the extent to which the team has shared objectives. The hypothesized moderating role of shared objectives received support in a study of faultlines formed by differences in gender, tenure, and functional background in 42 top management teams. The focus on top management teams has the additional benefit of providing the first test of the relationship between diversity faultlines and objective indicators of organizational performance. We discuss how these findings, and the innovative way in which we operationalized faultlines, extend faultline theory and research as well as offer guidelines to manage diversity faultlines.

Relational diversity, social integration and individual effectiveness: a social self-regulation perspective

Relational demographers and dissimilarity researchers contend that group members who are dissimilar (vs. similar) to their peers in terms of a given diversity attribute (e.g. demographics, attitudes, values or traits) feel less attached to their work group, experience less satisfying and more conflicted relationships with their colleagues, and consequently are less effective. However, qualitative reviews suggest empirical findings tend to be weak and inconsistent (Chattopadhyay, Tluchowska and George, 2004; Riordan, 2000; Tsui and Gutek, 1999), and that it remains unclear when, how and to what extent such differences (i.e. relational diversity) affect group members social integration (i.e. attachment with their work group, satisfaction and conflicted relationships with their peers) and effectiveness (Riordan, 2000). This absence of meta-analytically derived effect size estimates and the lack of an integrative theoretical framework leave practitioners with inconclusive advice regarding whether the effects elicited by relational diversity are practically relevant, and if so how these should be managed. The current research develops an integrative theoretical framework, which it tests by using meta-analysis techniques and adding two further empirical studies to the literature. The first study reports a meta-analytic integration of the results of 129 tests of the relationship between relational diversity with social integration and individual effectiveness. Using meta-analytic and structural equation modelling techniques, it shows different effects of surface- and deep-level relational diversity on social integration Specifically, low levels of interdependence accentuated the negative effects of surface-level relational diversity on social integration, while high levels of interdependence accentuated the negative effects of deep-level relational diversity on social integration. The second study builds on a social self-regulation framework (Abrams, 1994) and suggests that under high levels of interdependence relational diversity is not one but two things: visibility and separation. Using ethnicity as a prominent example it was proposed that separation has a negative effect on group members effectiveness leading for those high in visibility and low in separation to overall positive additive effects, while to overall negative additive effects for those low in visibility and high in separation. These propositions were sustained in a sample of 621 business students working in 135 ethnically diverse work groups in a business simulation course over a period of 24 weeks. The third study suggests visibility has a positive effect on group members self-monitoring, while separation has a negative effect. The study proposed that high levels of visibility and low levels of separation lead to overall positive additive effects on self-monitoring but overall negative additive effects for those low in visibility and high in separation. Results from four waves of data on 261 business students working in 69 ethnically diverse work groups in a business simulation course held over a period of 24 weeks support these propositions.