Practical photovoltaic simulator with a cross tackling control strategy based on the first-hand duty cycle processing

This paper proposes a methodological scheme for the photovoltaic (PV) simulator design. With the advantages of a digital controller system, linear interpolation is proposed for precise fitting with higher computational efficiency. A novel control strategy that directly tackles two different duty cycles is proposed and implemented to achieve a full-range operation including short circuit (SC) and open circuit (OC) conditions. Systematic design procedures for both hardware and algorithm are explained, and a prototype is built. Experimental results confirm an accurate steady state performance under different load conditions, including SC and OC. This low power apparatus can be adopted for PV education and research with a limited budget.

Adaptive control of hybrid battery energy storage systems under capacity fade

There is an increasing call for applications which use a mixture of batteries. These hybrid battery solutions may contain different battery types for example; using second life ex-transportation batteries in grid support applications or a combination of high power, low energy and low power, high energy batteries to meet multiple energy requirements or even the same battery types but under different states of health for example, being able to hot swap out a battery when it has failed in an application without changing all the batteries and ending up with batteries with different performances, capacities and impedances. These types of applications typically use multi-modular converters to allow hot swapping to take place without affecting the overall performance of the system. A key element of the control is how the different battery performance characteristics may be taken into account and the how the power is then shared among the different batteries in line with their performance. This paper proposes a control strategy which allows the power in the batteries to be effectively distributed even under capacity fade conditions using adaptive power sharing strategy. This strategy is then validated against a system of three different battery types connected to a multi-modular converter both with and without capacity fade mechanisms in place.

The effect of circuit parasitics on resonant switched capacitor converters

Switched Capacitor (SC) converters have been used for several years in low-power, power electronic energy conversion systems. However, because of their attractive features such as low-weight and high-density energy conversion and with the emergence of new circuit topologies and SiC switching devices, these circuits have recently been proposed for higher power applications. The resonant switched capacitor topology is a good candidate for high-power due to its very low-switching loss, but circuit parasitic inductance and resistance can have a significant effect on the resonant frequency of each cell. This paper discusses the influence of these parasitics on the performance of the converter and proposes a method by which these parasitics can be estimated. Simulation results and measurements from a hardware prototype are used to validate the technique.

DC-link voltage control strategy for reducing capacitance and total harmonic distortion in single-phase grid-connected photovoltaic inverters

High-volume capacitance is required to buffer the power difference between the input and output ports in single-phase grid-connected photovoltaic inverters, which become an obstacle to high system efficiency and long device lifetime. Furthermore, total harmonic distortion becomes serious when the system runs into low power level. In this study, a comprehensive analysis is introduced for two-stage topology with the consideration of active power, DC-link (DCL) voltage, ripple and capacitance. This study proposed a comprehensive DCL voltage control strategy to minimise the DCL capacitance while maintaining a normal system operation. Furthermore, the proposed control strategy is flexible to be integrated with the pulse-skipping control that significantly improves the power quality at light power conditions. Since the proposed control strategy needs to vary DCL voltage, an active protection scheme is also introduced to prevent any voltage violation across the DCL. The proposed control strategy is evaluated by both simulation and experiments, whose results confirm the system effectiveness.

An intelligent approach for deploying applications in WSN's

Wireless sensor networks have been identified as one of the key technologies for the 21st century. They consist of tiny devices with limited processing and power capabilities, called motes that can be deployed in large numbers of useful sensing capabilities. Even though, they are flexible and easy to deploy, there are a number of considerations when it comes to their fault tolerance, conserving energy and re-programmability that need to be addressed before we draw any substantial conclusions about the effectiveness of this technology. In order to overcome their limitations, we propose a middleware solution. The proposed scheme is composed based on two main methods. The first method involves the creation of a flexible communication protocol based on technologies such as Mobile Code/Agents and Linda-like tuple spaces. In this way, every node of the wireless sensor network will produce and process data based on what is the best for it but also for the group that it belongs too. The second method incorporates the above protocol in a middleware that will aim to bridge the gap between the application layer and low level constructs such as the physical layer of the wireless sensor network. A fault tolerant platform for deploying and monitoring applications in real time offers a number of possibilities for the end user giving him in parallel the freedom to experiment with various parameters, in an effort towards the deployed applications running in an energy efficient manner inside the network. The proposed scheme is evaluated through a number of trials aiming to test its merits under real time conditions and to identify its effectiveness against other similar approaches. Finally, parameters which determine the characteristics of the proposed scheme are also examined.

Power electronic interfaces for low voltage residential networks

A proposal to increase the existing residential LV grid voltage from 230 V to 300 V has been made in order to increase existing network capacity. A power-electronic AC-AC converter is then used to provide 230 V at each property. The equipment can also provide power-quality improvements to the network and load. Several constraints such as temperature rise at the converter location lead to a converter design requiring very high efficiency. In this paper different AC/AC converter topologies are presented which compares the power quality benefits, size and efficiency of each converter. The design and the control technique of the most suitable topology are verified using simulation and preliminary experimentally results of prototype hardware are also included. © 2013 IEEE.

Review of low-temperature vapour power cycle engines with quasi-isothermal expansion

External combustion heat cycle engines convert thermal energy into useful work. Thermal energy resources include solar, geothermal, bioenergy, and waste heat. To harness these and maximize work output, there has been a renaissance of interest in the investigation of vapour power cycles for quasi-isothermal (near constant temperature) instead of adiabatic expansion. Quasi-isothermal expansion has the advantage of bringing the cycle efficiency closer to the ideal Carnot efficiency, but it requires heat to be transferred to the working fluid as it expands. This paper reviews various low-temperature vapour power cycle heat engines with quasi-isothermal expansion, including the methods employed to realize the heat transfer. The heat engines take the form of the Rankine cycle with continuous heat addition during the expansion process, or the Stirling cycle with a condensable vapour as working fluid. Compared to more standard Stirling engines using gas, the specific work output is higher. Cryogenic heat engines based on the Rankine cycle have also been enhanced with quasi-isothermal expansion. Liquid flooded expansion and expander surface heating are the two main heat transfer methods employed. Liquid flooded expansion has been applied mainly in rotary expanders, including scroll turbines; whereas surface heating has been applied mainly in reciprocating expanders. © 2014 Elsevier Ltd.

Exploration of a simple, low cost, micro gas turbine recuperator solution for a domestic combined heat and power unit

For micro gas turbines (MGT) of around 1 kW or less, a commercially suitable recuperator must be used to produce a thermal efficiency suitable for use in UK Domestic Combined Heat and Power (DCHP). This paper uses computational fluid dynamics (CFD) to investigate a recuperator design based on a helically coiled pipe-in-pipe heat exchanger which utilises industry standard stock materials and manufacturing techniques. A suitable mesh strategy was established by geometrically modelling separate boundary layer volumes to satisfy y + near wall conditions. A higher mesh density was then used to resolve the core flow. A coiled pipe-in-pipe recuperator solution for a 1 kW MGT DCHP unit was established within the volume envelope suitable for a domestic wall-hung boiler. Using a low MGT pressure ratio (necessitated by using a turbocharger oil cooled journal bearing platform) meant unit size was larger than anticipated. Raising MGT pressure ratio from 2.15 to 2.5 could significantly reduce recuperator volume. Dimensional reasoning confirmed the existence of optimum pipe diameter combinations for minimum pressure drop. Maximum heat exchanger effectiveness was achieved using an optimum or minimum pressure drop pipe combination with large pipe length as opposed to a large pressure drop pipe combination with shorter pipe length. © 2011 Elsevier Ltd. All rights reserved.

Interhemispheric differences of spectral power in expressive language:a MEG study with clinical applications

In the last decade we have seen an exponential growth of functional imaging studies investigating multiple aspects of language processing. These studies have sparked an interest in applying some of the paradigms to various clinically relevant questions, such as the identification of the cortical regions mediating language function in surgical candidates for refractory epilepsy. Here we present data from a group of adult control participants in order to investigate the potential of using frequency specific spectral power changes in MEG activation patterns to establish lateralisation of language function using expressive language tasks. In addition, we report on a paediatric patient whose language function was assessed before and after a left hemisphere amygdalo-hippocampectomy. Our verb generation task produced left hemisphere decreases in beta-band power accompanied by right hemisphere increases in low beta-band power in the majority of the control group, a previously unreported phenomenon. This pattern of spectral power was also found in the patient's post-surgery data, though not her pre-surgery data. Comparison of pre and post-operative results also provided some evidence of reorganisation in language related cortex both inter- and intra-hemispherically following surgery. The differences were not limited to changes in localisation of language specific cortex but also changes in the spectral and temporal profile of frontal brain regions during verb generation. While further investigation is required to establish concordance with invasive measures, our data suggest that the methods described may serve as a reliable lateralisation marker for clinical assessment. Furthermore, our findings highlight the potential utility of MEG for the investigation of cortical language functioning in both healthy development and pathology.

Coherent propagation and energy transfer in low-dimension nonlinear arrays

We present a theory of coherent propagation and energy or power transfer in a low-dimension array of coupled nonlinear waveguides. It is demonstrated that in the array with nonequal cores (e.g., with the central core) stable steady-state coherent multicore propagation is possible only in the nonlinear regime, with a power-controlled phase matching. The developed theory of energy or power transfer in nonlinear discrete systems is rather generic and has a range of potential applications including both high-power fiber lasers and ultrahigh-capacity optical communication systems. © 2012 American Physical Society.

Everyday tactics and spaces of power: the role of informal economies in post-Soviet Ukraine

Utilising de Certeau's concepts of daily life and his delineation between strategies and tactics as everyday practices this paper examines the role of informal economies in post-Ukraine. Based on 700 household surveys and seventy-five in-depth interviews, conducted in three Ukrainian cities, the paper argues that individuals/households have developed a wide range of tactics in response to the economic marginalisation the country has endured since the collapse of the Soviet Union. Firstly, the paper details the importance of informal economies in contemporary Ukraine while highlighting that many such practices are operated out of necessity due to low wage and pension rates and high levels of corruption. This challenges state-produced statistics on the scale of economic marginalisation currently experienced in the country. By exploring a variety of these tactics the paper then examines how unequal power relations shape the spaces in which these practices operate in and how they can be simultaneously sites of exploitation and resistance to economic marginalisation. The paper concludes pessimistically by suggesting that the way in which these economic spaces are shaped precludes the development of state policies which might benefit the economically marginalised.

The EU's 'transnational power over' Central Asia:Developing and applying a structurally integrative approach to the study of the EU's power over Central Asia

This thesis challenges the consensual scholarly expectation of low EU impact in Central Asia. In particular, it claims that by focusing predominantly on narrow, micro-level factors, the prevailing theoretical perspectives risk overlooking less obvious aspects of the EU?s power, including structural aspects, and thus tend to underestimate the EU?s leverage in the region. Therefore, the thesis argues that a more structurally integrative and holistic approach is needed to understand the EU?s power in the region. In responding to this need, the thesis introduces a conceptual tool, which it terms „transnational power over? (TNPO). Inspired by debates in IPE, in particular new realist and critical IPE perspectives, and combining these views with insights from neorealist, neo-institutionalist and constructivist approaches to EU external relations, the concept of TNPO is an analytically eclectic notion, which helps to assess the degree to which, in today?s globalised and interdependent world, the EU?s power over third countries derives from its control over a combination of material, institutional and ideational structures, making it difficult for the EU?s partners to resist the EU?s initiatives or to reject its offers. In order to trace and assess the mechanisms of EU impact across these three structures, the thesis constructs a toolbox, which centres on four analytical distinctions: (i) EU-driven versus domestically driven mechanisms, (ii) mechanisms based on rationalist logics of action versus mechanisms following constructivist logics of action, (iii) agent-based versus purely structural mechanisms of TNPO, and (iv) transnational and intergovernmental mechanisms of EU impact. Using qualitative research methodology, the thesis then applies the conceptual model to the case of EU-Central Asia. It finds that the EU?s power over Central Asia effectively derives from its control over a combination of material, institutional and ideational structures, including its position as a leader in trade and investment in the region, its (geo)strategic and security-related capabilities vis-à-vis Central Asia, as well as the relatively dense level of institutionalisation of its relations with the five countries and the positive image of the EU in Central Asia as a more neutral actor.

A micro gas turbines for UK domestic combined heat and power

Various micro-radial compressor configurations were investigated using one-dimensional meanline and computational fluid dynamics (CFD) techniques for use in a micro gas turbine (MGT) domestic combined heat and power (DCHP) application. Blade backsweep, shaft speed, and blade height were varied at a constant pressure ratio. Shaft speeds were limited to 220 000 r/min, to enable the use of a turbocharger bearing platform. Off-design compressor performance was established and used to determine the MGT performance envelope; this in turn was used to assess potential cost and environmental savings in a heat-led DCHP operating scenario within the target market of a detached family home. A low target-stage pressure ratio provided an opportunity to reduce diffusion within the impeller. Critically for DCHP, this produced very regular flow, which improved impeller performance for a wider operating envelope. The best performing impeller was a low-speed, 170 000 r/min, low-backsweep, 15° configuration producing 71.76 per cent stage efficiency at a pressure ratio of 2.20. This produced an MGT design point system efficiency of 14.85 per cent at 993 W, matching prime movers in the latest commercial DCHP units. Cost and CO2 savings were 10.7 per cent and 6.3 per cent, respectively, for annual power demands of 17.4 MWht and 6.1 MWhe compared to a standard condensing boiler (with grid) installation. The maximum cost saving (on design point) was 14.2 per cent for annual power demands of 22.62 MWht and 6.1 MWhe corresponding to an 8.1 per cent CO2 saving. When sizing, maximum savings were found with larger heat demands. When sized, maximum savings could be made by encouraging more electricity export either by reducing household electricity consumption or by increasing machine efficiency.

Two-dimensional optical power distribution of side-out-coupled radiation from tilted FBGs in multimode fibre

Two-dimensional optical power distribution of the out-coupled radiation from UV-inscribed tilted fibre Bragg gratings (TFBGs) in multimode fibre (MMF) has been side-detected with high spatial/spectral resolution, showing a near-identical radiation mode profile to that measured from the fibre-end detection method. A comparative investigation of the radiation characteristics of TFBGs fabricated in singlemode fibre (SMF) and MMF clearly indicates that the radiation out-coupling is stronger and spatially more confined in MMF. The unique spatial-to-spectral encoding property of the coupling mechanism offers potential application in low-cost WDM devices.

The Effect of low-grade aggregates on the abrasion resistance of concrete

Three types of crushed rock aggregate were appraised, these being Carboniferous Sandstone, Magnesian Limestone and Jurassic Limestone. A comprehensive aggregate testing programme assessed the properties of these materials. Two series of specimen slabs were cast and power finished using recognised site procedures to assess firstly the influence of these aggregates as the coarse fraction, and secondly as the fine fraction. Each specimen slab was tested at 28 days under three regimes to simulate 2-body abrasion, 3-body abrasion and the effect of water on the abrasion of concrete. The abrasion resistance was measured using a recognised accelerated abrasion testing apparatus employing rotating steel wheels. Relationships between the aggregate and concrete properties and the abrasion resistance have been developed with the following properties being particularly important - Los Angeles Abrasion and grading of the coarse aggregate, hardness of the fine aggregate and water-cement ratio of the concrete. The sole use of cube strength as a measure of abrasion resistance has been shown to be unreliable by this work. A graphical method for predicting the potential abrasion resistance of concrete using various aggregate and concrete properties has been proposed. The effect of varying the proportion of low-grade aggregate in the mix has also been investigated. Possible mechanisms involved during abrasion have been discussed, including localised crushing and failure of the aggregate/paste bond. Aggregates from each of the groups were found to satisfy current specifications for direct finished concrete floors. This work strengthens the case for the increased use of low-grade aggregates in the future.