Surface acoustic wave devices with low loss and high frequency operation

This thesis describes an industrial research project carried out in collaboration with STC Components, Harlow, Essex. Technical and market trends in the use of surface acoustic wave (SAW) devices are reviewed. As a result, three areas not previously addressed by STC were identified: lower insertion loss designs, higher operating frequencies and improved temperature dependent stability. A review of the temperature performance of alternative lower insertion loss designs,shows that greater use could be made of the on-site quartz growing plant. Data is presented for quartz cuts in the ST-AT range. This data is used to modify the temperature performance of a SAW filter. Several recently identified quartz orientations have been tested. These are SST, LST and X33. Problems associated with each cut are described and devices demonstrated. LST quartz, although sensitive to accuracy of cut, is shown to have an improved temperature coefficient over the normal ST orientation. Results show that its use is restricted due to insertion loss variations with temperature. Effects associated with split-finger transducers on LST-quartz are described. Two low-loss options are studied, coupled resonator filters for very narrow bandwidth applications and single phase unidirectional transducers (SPUDT) for fractional bandwidths up to about 1%. Both designs can be implemented with one quarter wavelength transducer geometries at operating frequencies up to 1GHz. The SPUDT design utilised an existing impulse response model to provide analysis of ladder or rung transducers. A coupled resonator filter at 400MHz is demonstrated with a matched insertion loss of less than 3.5dB and bandwidth of 0.05%. A SPUDT device is designed as a re-timing filter for timing extraction in a long haul PCM transmission system. Filters operating at 565MHz are demonstrated with insertion losses of less than 6dB. This basic SPUDT design is extended to a maximally distributed version and demonstrated at 450MHz with 9.8dB insertion loss.

Detection of signals corrupted by the combination of Gaussian and Non-Gaussian noise

The detection of signals in the presence of noise is one of the most basic and important problems encountered by communication engineers. Although the literature abounds with analyses of communications in Gaussian noise, relatively little work has appeared dealing with communications in non-Gaussian noise. In this thesis several digital communication systems disturbed by non-Gaussian noise are analysed. The thesis is divided into two main parts. In the first part, a filtered-Poisson impulse noise model is utilized to calulate error probability characteristics of a linear receiver operating in additive impulsive noise. Firstly the effect that non-Gaussian interference has on the performance of a receiver that has been optimized for Gaussian noise is determined. The factors affecting the choice of modulation scheme so as to minimize the deterimental effects of non-Gaussian noise are then discussed. In the second part, a new theoretical model of impulsive noise that fits well with the observed statistics of noise in radio channels below 100 MHz has been developed. This empirical noise model is applied to the detection of known signals in the presence of noise to determine the optimal receiver structure. The performance of such a detector has been assessed and is found to depend on the signal shape, the time-bandwidth product, as well as the signal-to-noise ratio. The optimal signal to minimize the probability of error of; the detector is determined. Attention is then turned to the problem of threshold detection. Detector structure, large sample performance and robustness against errors in the detector parameters are examined. Finally, estimators of such parameters as. the occurrence of an impulse and the parameters in an empirical noise model are developed for the case of an adaptive system with slowly varying conditions.

An investigation into formal and functional characteristics of qualifications in legislative writing and its application to English for academic legal purposes.

The present investigation is based on a linguistic analysis of the 'Housing Act 1980' and attempts to examine the role of qualifications in the structuring of the legislative statement. The introductory chapter isolates legislative writing as a "sub-variety “of legal language and provides an overview of the controversies surrounding the way it is written and the problems it poses to its readers. Chapter two emphasizes the limitations of the available work on the description of language-varieties for the analysis of legislative writing and outlines the approach adopted for the present analysis. This chapter also gives some idea of the information-structuring of legislative provisions and establishes qualification as a key element in their textualisation. The next three chapters offer a detailed account of the ten major qualification-types identified in the corpus, concentrating on the surface form they take, the features of legislative statements they textualize and the syntactic positions to which they are generally assigned in the statement of legislative provisions. The emerging hypotheses in these chapters have often been verified through a specialist reaction from a Parliamentary Counsel, largely responsible for the writing of the ‘Housing Act 1980’• The findings suggest useful correlations between a number of qualificational initiators and the various aspects of the legislative statement. They also reveal that many of these qualifications typically occur in those clause-medial syntactic positions which are sparingly used in other specialist discourse, thus creating syntactic discontinuity in the legislative sentence. Such syntactic discontinuities, on the evidence from psycholinguistic experiments reported in chapter six, create special problems in the processing and comprehension of legislative statements. The final chapter converts the main linguistic findings into a series of pedagogical generalizations, offers indications of how this may be applied in EALP situations and concludes with other considerations of possible applications.

Privatization : problems of implementation in Egypt

This study aims to investigate to what extent the views of the managers of the enterprises to be privatized are a barrier to smooth implementation of privatization as opposed to other problems. Accordingly, the research tackles two main issues: Identification and analysis of the major problems encountered in the implementation of the Egyptian privatization programme and at which level these problems exist while proposing different approaches to tackle them; and views of public sector top and middle-level managers regarding the main issues of privatization. The study relies upon a literature survey, interviews with stakeholders, a survey of managers' attitudes and several illustrative case studies. A model of "good practice" for the smooth and effective implementation of privatization has been designed. Practice in Egypt has then been studied and compared with the "good practice" model. Lack of strictness and firmness in implementing the announced privatization programme has been found to be a characteristic of Egyptian practice. This is partly attributable to the inadequacy of the programme and partly to the different obstacles to implementation. The main obstacles are doubtful desirability of privatization on the part of the managers at different implementation levels, resistance of stakeholders, in adequately of the legal framework governing privatization, redundant labour, lack of an efficient monitoring system allowing for accountability, inefficient marketing of privatization, ineffective communication, insufficient information at different levels and problems related to valuation and selling procedures. A large part of the thesis is concerned with SOE (State Owned Enterprise) managers' attitudes on and understanding of the privatization (appraised through surveys). Although most managers have stated their acceptance of privatization, many of their responses show that they do not accept selling SOEs. They understand privatization to include enterprise reform and restructuring, changing procedures and giving more authority to company executives, but not necessarily as selling SOEs. The majority of managers still see many issues that have to be addressed for smooth implementation of privatization e.g. insufficiency of information, incompleteness of legal framework, restructuring and labour problems. The main contribution to knowledge of this thesis is the study of problems of implementing privatization in developing countries especially managers' resistance to privatization as a major change, partly because of the threat it poses and partly because of the lack of understanding of privatization and implications of operating private businesses. A programme of persuading managers and offsetting the unfavourable effects is recommended as an outcome of the study. Five different phrases and words for the national Index to theses are: Egypt, privatization, implementation of privatization, problems of implementing privatization and managers' attitudes towards privatization.

Aspects of the design and control of manufacturing systems subject to demand uncertainty

The recent explosive growth in advanced manufacturing technology (AMT) and continued development of sophisticated information technologies (IT) is expected to have a profound effect on the way we design and operate manufacturing businesses. Furthermore, the escalating capital requirements associated with these developments have significantly increased the level of risk associated with initial design, ongoing development and operation. This dissertation has examined the integration of two key sub-elements of the Computer Integrated Manufacturing (CIM) system, namely the manufacturing facility and the production control system. This research has concentrated on the interactions between production control (MRP) and an AMT based production facility. The disappointing performance of such systems has been discussed in the context of a number of potential technological and performance incompatibilities between these two elements. It was argued that the design and selection of operating policies for both is the key to successful integration. Furthermore, policy decisions are shown to play an important role in matching the performance of the total system to the demands of the marketplace. It is demonstrated that a holistic approach to policy design must be adopted if successful integration is to be achieved. It is shown that the complexity of the issues resulting from such an approach required the formulation of a structured design methodology. Such a methodology was subsequently developed and discussed. This combined a first principles approach to the behaviour of system elements with the specification of a detailed holistic model for use in the policy design environment. The methodology aimed to make full use of the `low inertia' characteristics of AMT, whilst adopting a JIT configuration of MRP and re-coupling the total system to the market demands. This dissertation discussed the application of the methodology to an industrial case study and the subsequent design of operational policies. Consequently a novel approach to production control resulted. A central feature of which was a move toward reduced manual intervention in the MRP processing and scheduling logic with increased human involvement and motivation in the management of work-flow on the shopfloor. Experimental results indicated that significant performance advantages would result from the adoption of the recommended policy set.

Magnetoencephalography:technical improvements in image co-registration and studies of visual cortical oscillations

The work presented in this thesis is divided into two distinct sections. In the first, the functional neuroimaging technique of Magnetoencephalography (MEG) is described and a new technique is introduced for accurate combination of MEG and MRI co-ordinate systems. In the second part of this thesis, MEG and the analysis technique of SAM are used to investigate responses of the visual system in the context of functional specialisation within the visual cortex. In chapter one, the sources of MEG signals are described, followed by a brief description of the necessary instrumentation for accurate MEG recordings. This chapter is concluded by introducing the forward and inverse problems of MEG, techniques to solve the inverse problem, and a comparison of MEG with other neuroimaging techniques. Chapter two provides an important contribution to the field of research with MEG. Firstly, it is described how MEG and MRI co-ordinate systems are combined for localisation and visualisation of activated brain regions. A previously used co-registration methods is then described, and a new technique is introduced. In a series of experiments, it is demonstrated that using fixed fiducial points provides a considerable improvement in the accuracy and reliability of co-registration. Chapter three introduces the visual system starting from the retina and ending with the higher visual rates. The functions of the magnocellular and the parvocellular pathways are described and it is shown how the parallel visual pathways remain segregated throughout the visual system. The structural and functional organisation of the visual cortex is then described. Chapter four presents strong evidence in favour of the link between conscious experience and synchronised brain activity. The spatiotemporal responses of the visual cortex are measured in response to specific gratings. It is shown that stimuli that induce visual discomfort and visual illusions share their physical properties with those that induce highly synchronised gamma frequency oscillations in the primary visual cortex. Finally chapter five is concerned with localization of colour in the visual cortex. In this first ever use of Synthetic Aperture Magnetometry to investigate colour processing in the visual cortex, it is shown that in response to isoluminant chromatic gratings, the highest magnitude of cortical activity arise from area V2.

Productivity analysis and measurement

The state of the art in productivity measurement and analysis shows a gap between simple methods having little relevance in practice and sophisticated mathematical theory which is unwieldy for strategic and tactical planning purposes, -particularly at company level. An extension is made in this thesis to the method of productivity measurement and analysis based on the concept of added value, appropriate to those companies in which the materials, bought-in parts and services change substantially and a number of plants and inter-related units are involved in providing components for final assembly. Reviews and comparisons of productivity measurement dealing with alternative indices and their problems have been made and appropriate solutions put forward to productivity analysis in general and the added value method in particular. Based on this concept and method, three kinds of computerised models two of them deterministic, called sensitivity analysis and deterministic appraisal, and the third one, stochastic, called risk simulation, have been developed to cope with the planning of productivity and productivity growth with reference to the changes in their component variables, ranging from a single value 'to• a class interval of values of a productivity distribution. The models are designed to be flexible and can be adjusted according to the available computer capacity expected accuracy and 'presentation of the output. The stochastic model is based on the assumption of statistical independence between individual variables and the existence of normality in their probability distributions. The component variables have been forecasted using polynomials of degree four. This model is tested by comparisons of its behaviour with that of mathematical model using real historical data from British Leyland, and the results were satisfactory within acceptable levels of accuracy. Modifications to the model and its statistical treatment have been made as required. The results of applying these measurements and planning models to the British motor vehicle manufacturing companies are presented and discussed.

Building cliques and alliances as practices to 'make things happen' in complex networks

The Roma population has become a policy issue highly debated in the European Union (EU). The EU acknowledges that this ethnic minority faces extreme poverty and complex social and economic problems. 52% of the Roma population live in extreme poverty, 75% in poverty (Soros Foundation, 2007, p. 8), with a life expectancy at birth of about ten years less than the majority population. As a result, Romania has received a great deal of policy attention and EU funding, being eligible for 19.7 billion Euros from the EU for 2007-2013. Yet progress is slow; it is debated whether Romania's government and companies were capable to use these funds (EurActiv.ro, 2012). Analysing three case studies, this research looks at policy implementation in relation to the role of Roma networks in different geographical regions of Romania. It gives insights about how to get things done in complex settings and it explains responses to the Roma problem as a „wicked‟ policy issue. This longitudinal research was conducted between 2008 and 2011, comprising 86 semi-structured interviews, 15 observations, and documentary sources and using a purposive sample focused on institutions responsible for implementing social policies for Roma: Public Health Departments, School Inspectorates, City Halls, Prefectures, and NGOs. Respondents included: governmental workers, academics, Roma school mediators, Roma health mediators, Roma experts, Roma Councillors, NGOs workers, and Roma service users. By triangulating the data collected with various methods and applied to various categories of respondents, a comprehensive and precise representation of Roma network practices was created. The provisions of the 2001 „Governmental Strategy to Improve the Situation of the Roma Population‟ facilitated forming a Roma network by introducing special jobs in local and central administration. In different counties, resources, people, their skills, and practices varied. As opposed to the communist period, a new Roma elite emerged: social entrepreneurs set the pace of change by creating either closed cliques or open alliances and by using more or less transparent practices. This research deploys the concept of social/institutional entrepreneurs to analyse how key actors influence clique and alliance formation and functioning. Significantly, by contrasting three case studies, it shows that both closed cliques and open alliances help to achieve public policy network objectives, but that closed cliques can also lead to failure to improve the health and education of Roma people in a certain region.

Measurement of productivity and cost of the direct labour organisation within highways maintenance departments

The objective of this thesis is to investigate, through an empirical study, the different functions of the highways maintenance departments and to suggest methods by means of which road maintenance work could be carried out in a more efficient way by utilising its resources of men, material and plant to the utmost advantage. This is particularly important under the present circumstances of national financial difficulties which have resulted in continuous cuts in public expenditure. In order to achieve this objective, the researcher carried out a survey among several Highways Authorities by means of questionnaire and interview. The information so collected was analysed in order to understand the actual, practical situation within highways manintenance departments, and highlight any existing problems, and try to answer the question of how they could become more efficient. According to the results obtained by the questionnaire and the interview, and the analysis of these results, the researcher concludes that it is the management system where least has been done, and where problems exist and are most complex. The management of highways maintenance departments argue that the reasons for their problems include both financial and organisational difficulties, apart from the political aspect and nature of the activities undertaken. The researcher believes that this ought to necessitate improving the management's analytical tools and techniques in order to achieve the most effective way of performing each activity. To this end the researcher recommends several related procedures to be adopted by the management of the highways maintenance departments. These recommendations, arising from the study, involve the technical, practical and human aspects. These are essential factors of which management should be aware - and certainly should not neglect - in order to achieve its objectives of improved productivity in the highways maintenance departments.

Changes in information processing in children and their implications for marketing strategy

This thesis examines children's consumer choice behaviour using an information processing perspective, with the fundamental goal of applying academic research to practical marketing and commercial problems. Proceeding a preface, which describes the academic and commercial terms of reference within which this interdisciplinary study is couched, the thesis comprises four discernible parts. Initially, the rationale inherent in adopting an information processing perspective is justified and the diverse array of topics which have bearing on children's consumer processing and behaviour are aggregated. The second part uses this perspective as a springboard to appraise the little explored role of memory, and especially memory structure, as a central cognitive component in children's consumer choice processing. The main research theme explores the ease with which 10 and 11 year olds retrieve contemporary consumer information from subjectively defined memory organisations. Adopting a sort-recall paradigm, hierarchical retrieval processing is stimulated and it is contended that when two items, known to be stored proximally in the memory organisation are not recalled adjacently, this discrepancy is indicative of retrieval processing ease. Results illustrate the marked influence of task conditions and orientation of memory structure on retrieval; these conclusions are accounted for in terms of input and integration failure. The third section develops the foregoing interpellations in the marketing context. A straightforward methodology for structuring marketing situations is postulated, a basis for segmenting children's markets using processing characteristics is adopted, and criteria for communicating brand support information to children are discussed. A taxonomy of market-induced processing conditions is developed. Finally, a case study with topical commercial significance is described. The development, launch and marketing of a new product in the confectionery market is outlined, the aetiology of its subsequent demise identified and expounded, and prescriptive guidelines are put forward to help avert future repetition of marketing misjudgements.

Organisational change and safety culture: the impact of communication

This research examines and explains the links between safety culture and communication. Safety culture is a concept that in recent years has gained prominence but there has been little applied research conducted to investigate the meaning of the concept in 'real life' settings. This research focused on a Train Operating Company undergoing change in a move towards privatisation. These changes were evident in the management of safety, the organisation of the industry and internally in their management. The Train Operating Company's management took steps to improve their safety culture and communications through the development of a cascade communication structure. The research framework employed a qualitative methodology in order to investigate the effect of the new system on safety culture. Findings of the research were that communications in the organisation failed to be effective for a number of reasons, including both cultural and logistical problems. The cultural problems related to a lack of trust in the organisation by the management and the workforce, the perception of communications as management propaganda, and asyntonic communications between those involved, whilst logistical problems related to the inherent difficulties of communicating over a geographically distributed network. An organisational learning framework was used to explain the results. It is postulated that one of the principal reasons why change, either to the safety culture or to communications, did not occur was because of the organisation's inability to learn. The research has also shown the crucial importance of trust between the members of the organisation, as this was one of the fundamental reasons why the safety culture did not change, and why safety management systems were not fully implemented. This is consistent with the notion of mutual trust in the HSC (1993) definition of safety culture. This research has highlighted its relevance to safety culture and its importance for organisational change.

Stand-alone groundwater desalination system using reverse osmosis combined with a cooled greenhouse for use in arid and semi-arid zones of India

In many areas of northern India, salinity renders groundwater unsuitable for drinking and even for irrigation. Though membrane treatment can be used to remove the salt, there are some drawbacks to this approach e.g. (1) depletion of the groundwater due to over-abstraction, (2) saline contamination of surface water and soil caused by concentrate disposal and (3) high electricity usage. To address these issues, a system is proposed in which a photovoltaic-powered reverse osmosis (RO) system is used to irrigate a greenhouse (GH) in a stand-alone arrangement. The concentrate from the RO is supplied to an evaporative cooling system, thus reducing the volume of the concentrate so that finally it can be evaporated in a pond to solid for safe disposal. Based on typical meteorological data for Delhi, calculations based on mass and energy balance are presented to assess the sizing and cost of the system. It is shown that solar radiation, freshwater output and evapotranspiration demand are readily matched due to the approximately linear relation among these variables. The demand for concentrate varies independently, however, thus favouring the use of a variable recovery arrangement. Though enough water may be harvested from the GH roof to provide year-round irrigation, this would require considerable storage. Some practical options for storage tanks are discussed. An alternative use of rainwater is in misting to reduce peak temperatures in the summer. An example optimised design provides internal temperatures below 30EC (monthly average daily maxima) for 8 months of the year and costs about €36,000 for the whole system with GH floor area of 1000 m2 . Further work is needed to assess technical risks relating to scale-deposition in the membrane and evaporative pads, and to develop a business model that will allow such a project to succeed in the Indian rural context.

The 'Healthy Passport' intervention with older people in an English urban environment:effects of incentives and peer-group organisers in promoting healthy living

This paper reports the evaluation of the effectiveness of incentives (viz. points and prizes) and of peer-group organisers ('older people's champions') in the outcomes of a health-improvement programme for people aged 50 + years in a multi-ethnic district of the West Midlands, England. Health promotion activities Were provided, and adherence, outcome variables and barriers to adherence were assessed over six months, using a `passport' format. Those aged in the fifties and of Asian origin Were under represented, but people of Afro-Caribbean origin were well represented and proportionately most likely to stay in the project. Those of greater age and With more illness were most likely to drop out. There were significant improvements in exercise, diet and the uptake of influenza vaccines and eyesight tests, but slighter improvements in wellbeing. Positive outcomes related to the incentives and to liking the format. The number of reported barriers was associated with lower involvement and lack of change, as was finding activities too difficult, the level of understanding, and transport and mobility problems, but when these were controlled, age did not predict involvement. Enjoying the scheme was related to positive changes, and this was associated with support from the older people's champions.

Comparing regional organizations in global multilateral institutions:ASEAN, the EU and the UN

Structural change brought about by the end of the Cold War and accelerated globalisation have transformed the global environment. A global governance complex is emerging, characterised by an ever-greater functional and regulatory role for multilateral organisations such as the United Nations (UN) and its associated agencies. The evolving global governance framework has created opportunities for regional organisations to participate as actors within the UN (and other multilateral institutions). This article compares the European Union (EU) and Association of Southeast Asian Nations (ASEAN) as actors within the UN network. It begins by extrapolating framework conditions for the emergence of EU and ASEAN actorness from the literature. The core argument of this article is that EU and ASEAN actorness is evolving in two succinct stages: Changes in the global environment create opportunities for the participation of regional organisations in global governance institutions, exposing representation and cohesion problems at the regional level. In response, ASEAN and the EU have initiated processes of institutional adaptation.