The combination of smart hydrogels and fibre optic sensor technology for analyte detection

The subject of investigation of the present research is the use of smart hydrogels with fibre optic sensor technology. The aim was to develop a costeffective sensor platform for the detection of water in hydrocarbon media, and of dissolved inorganic analytes, namely potassium, calcium and aluminium. The fibre optic sensors in this work depend upon the use of hydrogels to either entrap chemotropic agents or to respond to external environmental changes, by changing their inherent properties, such as refractive index (RI). A review of current fibre optic technology for sensing outlined that the main principles utilised are either the measurement of signal loss or a change in wavelength of the light transmitted through the system. The signal loss principle relies on changing the conditions required for total internal reflection to occur. Hydrogels are cross-linked polymer networks that swell but do not dissolve in aqueous environments. Smart hydrogels are synthetic materials that exhibit additional properties to those inherent in their structure. In order to control the non-inherent properties, the hydrogels were fabricated with the addition of chemotropic agents. For the detection of water, hydrogels of low refractive index were synthesized using fluorinated monomers. Sulfonated monomers were used for their extreme hydrophilicity as a means of water sensing through an RI change. To enhance the sensing capability of the hydrogel, chemotropic agents, such as pH indicators and cobalt salts, were used. The system comprises of the smart hydrogel coated onto an exposed section of the fibre optic core, connected to the interrogation system measuring the difference in the signal. Information obtained was analysed using a purpose designed software. The developed sensor platform showed that an increase in the target species caused an increase in the signal lost from the sensor system, allowing for a detection of the target species. The system has potential applications in areas such as clinical point of care, water detection in fuels and the detection of dissolved ions in the water industry.

Fibre Bragg grating sensor interrogation using an acousto-optic tunable filter and low-coherence interferometry

We describe how an acousto-optic tunable filter can be used to both demultiplex the signals from multiple fibre Bragg grating sensors and simultaneously provide wide bandwidth signal demodulation in a system using interferometric wavelength shift detection. In an experimental demonstration, the approach provided a noise limited strain resolution of 24.9 n epsilon Hz(-1/ 2) at 15 Hz.

Low thermal sensitivity grating devices based on ex-45° tilting structure capable of forward-propagating cladding modes coupling

The authors describe a detailed investigation on tilted fiber Bragg grating (TFBG) structures with tilted angles exceeding 45°. In contrast to the backward mode coupling mechanism of Bragg gratings with normal and small tilting structures, the ex-45° TFBGs facilitate the light coupling to the forward-propagating cladding modes. The authors have also theoretically and experimentally examined the mode coupling transition of TFBGs with small, medium, and large tilt angles. In particular, experiments are conducted to investigate the spectra and far-field distribution, as well as temperature, strain, and refractive-index sensitivities of ex-45° devices. It has been revealed that these ex-45° gratings exhibit ultralow thermal sensitivity. As in-fiber devices, they may be superior to conventional Bragg and long-period gratings when the low thermal cross sensitivity is required.

Engineering liposomal systems to develop solubility enhancing technology

This research primarily focused on identifying the formulation parameters which control the efficacy of liposomes as delivery systems to enhance the delivery of poorly soluble drugs. Preliminary studies focused on the drug loading of ibuprofen within vesicle systems. Initially both liposomal and niosomal formulations were screened for their drug-loading capacity: liposomal systems were shown to offer significantly higher ibuprofen loading and thereafter lipid based systems were further investigated. Given the key role cholesterol is known to play within the stability of bilayer vesicles. the optimum cholesterol content in terms of drug loading and release of poorly soluble drugs was then investigated. From these studies a concentration of 11 total molar % of cholesterol was used as a benchmark for all further formulations. Investigating the effect of liposomc composition on several low solubility drugs, drug loading was shown to be enhanced by adopting longer chain length lipids. cationic lipids and. decreasing drug molecular weight. Drug release was increased by using cationic lipids and lower molecular weight of drug; conversely, a reduction was noted when employing longer chain lipids thus supporting the rational of longer chain lipids producing more stable liposomes, a theory also supported by results obtained via Langmuir studies· although it was revealed that stability is also dependent on geometric features associated with the lipid chain moiety. Interestingly, reduction in drug loading appeared to be induced when symmetrical phospholipids were substituted for lipids constituting asymmetrical alkyl chain groups thus further highlighting the importance of lipid geometry. Combining a symmetrical lipid with an asymmetrical derivative enhanced encapsulation of a hydrophobic drug while reducing that of another suggesting the importance of drug characteristics. Phosphatidylcholine liposornes could successfully be prepared (and visualised using transmission electron microscopy) from fatty alcohols therefore offering an alternative liposomal stabiliser to cholesterol. Results obtained revealed that liposomes containing tetradecanol within their formulation shares similar vesicle size, drug encapsulation, surface charge. and toxicity profiles as liposomes formulated with cholesterol, however the tetradecanol preparation appeared to release considerably more drug during stability studies. Langmuir monolayer studies revealed that the condensing influence by tetradecanol is less than compared with cholesterol suggesting that this reduced intercalation by the former could explain why the tetradecanol formulation released more drug compared with cholesterol formulations. Environmental scanning electron microscopy (ESEM) was used to analyse the morphology and stability of liposomes. These investigations indicated that the presence of drugs within the liposomal bilayer were able to enhance the stability of the bilayers against collapse under reduced hydration conditions. In addition the presence of charged lipids within the formulation under reduced hydration conditions compared with its neutral counterpart. However the applicability of using ESEM as a new method to investigate liposome stability appears less valid than first hoped since the results are often open to varied interpretation and do not provide a robust set of data to support conclusions in some cases.

Learning by exporting:lessons from high-technology SMEs

We investigate the learning by exporting hypothesis by examining the effect of exporting on the subsequent innovation performance of a sample of high-technology SMEs based in the UK. We find evidence of learning by exporting, but the pattern of this effect is complex. Exporting helps high-tech SMEs innovate subsequently, but does not make them more innovation intensive. There is evidence that consistent exposure to export markets helps firms overcome the innovation hurdle, but that there is a positive scale effect of exposure to export markets which allows innovative firms to sell more of their new-to-market products on entering export markets. Service sector firms are able to reap the benefits of exposure to export markets at an earlier (entry) stage of the internationalization process than are manufacturing firms. Innovation-intensive firms exhibit a different pattern of entry to and exit from export markets from low-intensity innovators, and this is reflected in different effects of exporting. © 2012 Elsevier Ltd.

Learning by exporting:lesson from high-technology SMEs

Theory points to the existence of a learning by exporting effect, in which exposure to export markets enhances performance through exposure to the knowledge stocks of trading partners. We investigate the learning by exporting hypothesis by examining the effect of exporting on the subsequent innovation performance of UK high-tech SMEs. We find evidence of learning by exporting, but the pattern of this effect is relatively complex. Exporting helps high-tech SMEs innovate subsequently, but does not make them more innovation intensive. There is also evidence that it is consistent exposure to export markets that helps firms overcome the innovation hurdle, but that there is a positive scale effect of exposure to export markets which allows innovative firms to sell more of their new-to-market products on entering export markets. Service sector firms are able to reap the benefits of exposure to export markets at an earlier (entry) stage of the internationalization process than are manufacturing firms. Firms producing a rapidly changing portfolio of innovative products exhibit higher churn in terms of entry to and exit from export markets than low-intensity innovators, and this is reflected in the effects of entry and exit into and out of such markets.

Low severity Fischer-Tropsch synthesis for the production of synthetic hydrocarbon fuels

Currently, the main source for the production of liquid transportation fuels is petroleum, the continued use of which faces many challenges including depleting oil reserves, significant oil price rises, and environmental concerns over global warming which is widely believed to be due to fossil fuel derived CO2 emissions and other greenhouse gases. In this respect, lignocellulosic or plant biomass is a particularly interesting resource as it is the only renewable source of organic carbon that can be converted into liquid transportation fuels. The gasification of biomass produces syngas which can then be converted into synthetic liquid hydrocarbon fuels by means of the Fischer-Tropsch (FT) synthesis. This process has been widely considered as an attractive option for producing clean liquid hydrocarbon fuels from biomass that have been identified as promising alternatives to conventional fossil fuels like diesel and kerosene. The resulting product composition in FT synthesis is influenced by the type of catalyst and the reaction conditions that are used in the process. One of the issues facing this conversion process is the development of a technology that can be scaled down to match the scattered nature of biomass resources, including lower operating pressures, without compromising liquid composition. The primary aims of this work were to experimentally explore FT synthesis at low pressures for the purpose of process down-scaling and cost reduction, and to investigate the potential for obtaining an intermediate FT synthetic crude liquid product that can be integrated into existing refineries under the range of process conditions employed. Two different fixed-bed micro-reactors were used for FT synthesis; a 2cm3 reactor at the University of Rio de Janeiro (UFRJ) and a 20cm3 reactor at Aston University. The experimental work firstly involved the selection of a suitable catalyst from three that were available. Secondly, a parameter study was carried out on the 20cm3 reactor using the selected catalyst to investigate the influence of reactor temperature, reactor pressure, space velocity, the H2/CO molar ratio in the feed syngas and catalyst loading on the reaction performance measured as CO conversion, catalyst stability, product distribution, product yields and liquid hydrocarbon product composition. From this parameter study a set of preferred operating conditions was identified for low pressure FT synthesis. The three catalysts were characterized using BET, XRD, TPR and SEM. The catalyst selected was an unpromoted Co/Al2O3 catalyst. FT synthesis runs on the 20cm3 reactor at Aston were conducted for 48 hours. Permanent gases and light hydrocarbons (C1-C5) were analysed in an online GC-TCD/FID at hourly intervals. The liquid hydrocarbons collected were analyzed offline using GC-MS for determination of fuel composition. The parameter study showed that CO conversion and liquid hydrocarbon yields increase with increasing reactor pressure up to around 8 bar, above which the effect of pressure is small. The parameters that had the most significant influence on CO conversion, product selectivity and liquid hydrocarbon yields were reactor temperature and catalyst loading. The preferred reaction conditions identified for this research were: T = 230ºC, P = 10 bar, H2/CO = 2.0, WHSV = 2.2 h-1, and catalyst loading = 2.0g. Operation in the low range of pressures studied resulted in low CO conversions and liquid hydrocarbon yields, indicating that low pressure BTL-FT operation may not be industrially viable as the trade off in lower CO conversions and once-through liquid hydrocarbon product yields has to be carefully weighed against the potential cost savings resulting from process operation at lower pressures.

Attitudes towards advanced manufacturing technology (AMT):the role of AMT experience, skill level and job involvement

Studied the attitudes of shopfloor employees toward AMT as a function of experience with working with AMT, skill level, and job involvement. Survey data were collected from 115 employees of a large microelectronics company in England. Four job types were identified, which differed in terms of mode of work (manual/AMT) and skill level (low/high). Results show that those who worked with computers had more favorable attitudes toward AMT than those who did not. Results support A. Rafaeli's (see record 1986-20891-001) finding that the most favorable attitudes toward AMT were held by those who worked with computers and had high job involvement. Skill level had no significant effects on Ss' attitudes.

Technology transfer and sustainable industrial development for developing countries

This paper reports on a part of work for the UNIDO initiative on technology transfer for sustainable industrial development. The proposed technology transfer framework, adapted from the East Asian late industrialisers model, identifies two categories of countries requiring support for enhancing their technological capabilities: (a) very late industrialisers (“low income” developing countries), and (b) slow industrialisers (countries with sizeable manufacturing sectors but limited success in gaining international competitiveness) and three technology transfer routes: (a) through trade and aid to strengthen indigenous production for domestic markets (Route 1); (b) through FDI and contracting to develop export oriented firms (Route 2), and (c) through the supply chain of capital equipment and materials to develop local subcontracting capacity (Route 3). Very late industrialisers need support to start with Route 1 in selected sectors and upgrade through imported mature technologies. Appropriate product innovations are also possible. The slow industrialisers have more scope for increased technology transfer through Routes 2 and 3.

Hidden in plain sight:low-literacy adults in a developed country overcoming social and educational challenges through mobile learning support tools

Illiteracy is often associated with people in developing countries. However, an estimated 50 % of adults in a developed country such as Canada lack the literacy skills required to cope with the challenges of today's society; for them, tasks such as reading, understanding, basic arithmetic, and using everyday items are a challenge. Many community-based organizations offer resources and support for these adults, yet overall functional literacy rates are not improving. This is due to a wide range of factors, such as poor retention of adult learners in literacy programs, obstacles in transferring the acquired skills from the classroom to the real life, personal attitudes toward learning, and the stigma of functional illiteracy. In our research we examined the opportunities afforded by personal mobile devices in providing learning and functional support to low-literacy adults. We present the findings of an exploratory study aimed at investigating the reception and adoption of a technological solution for adult learners. ALEX© is a mobile application designed for use both in the classroom and in daily life in order to help low-literacy adults become increasingly literate and independent. Such a solution complements literacy programs by increasing users' motivation and interest in learning, and raising their confidence levels both in their education pursuits and in facing the challenges of their daily lives. We also reflect on the challenges we faced in designing and conducting our research with two user groups (adults enrolled in literacy classes and in an essential skills program) and contrast the educational impact and attitudes toward such technology between these. Our conclusions present the lessons learned from our evaluations and the impact of the studies' specific challenges on the outcome and uptake of such mobile assistive technologies in providing practical support to low-literacy adults in conjunction with literacy and essential skills training. © 2013 Her Majesty the Queen in Right of Canada.

Actively modelocked dual-wavelength fibre laser with ultra-low inter-pulse-stream timing jitter

We demonstrate a novel dual-wavelength erbium-fiber laser that uses a single nonlinear-optical loop mirror modulator to simultaneously modelock two cavities with chirped fiber Bragg gratings as end mirrors. We show that this configuration produces synchronized soliton pulse trains with an ultra-low RMS inter-pulse-stream timing jitter of 620 fs enabling application to multiwavelength systems at data rates in excess of 130 Gb/s. © 1995 IEEE

Fibre Bragg grating sensor interrogation using an acousto-optic tunable filter and low-coherence interferometry

We describe how an acousto-optic tunable filter can be used to both demultiplex the signals from multiple fibre Bragg grating sensors and simultaneously provide wide bandwidth signal demodulation in a system using interferometric wavelength shift detection. In an experimental demonstration, the approach provided a noise limited strain resolution of 24.9 nε Hz -1/2 at 15 Hz. © 2007 IOP Publishing Ltd.

Technology adoption in small and medium-sized logistics providers

Purpose - The main aim of the research is to shed light on the role of information and communication technology (ICT) in the logistics innovation process of small and medium-sized third party logistics providers (3PLs). Design/methodology/approach - A triangulated research strategy was designed using a combination of quantitative and qualitative methods. The former involved the use of a questionnaire survey of small and medium-sized Italian 3PLs with 153 usable responses received. The latter comprised a series of focus groups and the use of seven case studies. Findings - There is a relatively low level of ICT expenditure with few companies adopting formal technology investment strategies. The findings highlight the strategic importance of supply chain integration for 3PLs with companies that have embarked on an expansion of their service portfolios showing a higher level of both ICT usage and information integration. Lack of technology skills in the workforce is a major constraint on ICT adoption. Given the proliferation of logistics-related ICT tools and applications in recent years it has been difficult for small and medium-sized 3PLs to select appropriate applications. Research limitations/implications - The paper provides practical guidelines to researchers in the effective use of mixed-methods research based on the concept of methodological triangulation. In particular, it shows how questionnaire surveys, focus groups and case study analysis can be used in combination to provide insights into multi-faceted supply chain phenomena. It also identifies several potentially fruitful avenues for future research in this specific field. Practical implications - The paper's findings provide useful guidance for practitioners on the effective adoption of ICT as part of the logistics innovation process. The findings also provide support for ICT vendors in the design of ICT solutions that are aligned to the needs of small 3PLs. Originality/value - There is currently a paucity of research into the drivers and inhibitors of ICT in the innovation processes of small and medium-sized 3PLs. This paper fills this gap by exploring the issue using a range of complementary research approaches. Copyright © 2013 Emerald Group Publishing Limited. All rights reserved.

A multiwavelength low-power wavelength-locked slotted Fabry-Perot laser source for WDM applications

Wavelength-locking of a multiwavelength stabilized slotted Fabry-Perot (SFP) laser to a single-mode laser source is experimentally demonstrated. The SFP resonates at channels spaced by similar to 8 nm between 1510 and 1565 nm over a wide range of temperatures and drive currents. Under low-power (<- 20 dBm) external optical injection, wavelength-locking with a sidemode suppression ratio (SMSR) > 25 dB is achieved. A locking width of > 25 GHz and SMSR > 30 dB can be achieved for each locked wavelength channel at injection power > - 16 dBm.

Second harmonic generation in a low-loss orientation-patterned GaAs waveguide

The technology of low-loss orientation-patterned gallium arsenide (OP-GaAs) waveguided crystals was developed and realized by reduction of diffraction scattering on the waveguide pattern. The propagation losses in the OP-GaAs waveguide were estimated to be as low as 2.1 dB/cm, thus demonstrating the efficient second harmonic generation at 1621 nm under an external pumping. © 2013 Optical Society of America.