The mechanics of creep crack growth in a Magnox alloy

Magnox AL80 has been used for a study of creep crack propagation. A number of variables have been considered such as specimen geometry,notch root radius, material thickness, creep prestrain and stress level.The work has covered the material behaving under two values of the creep exponent, n=3.5 and n=7, according to the stress level. As well as observing initiation times and crack growth rates, scribed grids have been used to examine the near crack tip strain levels and distributions. It was shown that estimations of COD from notch flank opening can give misleading indications of material behaviour and that a more informative method was to monitor displacements in the material surrounding the crack tip. Strong evidence was found for crack advance being displacement controlled, however it was shown that the COD approach should be considered geometry dependant. The summation of ∈xx and ∈yy provided the most successful description of crack advance as it produced a single value that described propagation in all the cases concidered. The strain distributions indicates that σyy was related to distance from a point ahead of the crack tip by the exponent - (l/n+l) and that σxx is proportional to σyy. The constraint stresses arising in the DEN and CN specimens were evaluated. Initiation time was found to be principally affected by the stress level but was modified by the constraints arising from specimen geometry. Crack growth was found not to obey either the empirical K or σpett relationships but was reviewed in context of the observed strain behaviour.

The effects of substrate water availability on the isolation and growth of fungi

The work reported in this thesis was carried out to contribute to the knowledge of the effects of substrate water availability or water activity (a ) on fungal growth parameters and its implications in the preparationw of materials susceptible to biodeterioration. Fungi were isolated from soils of different ecological sites at a range of substrate aw levels controlled by sodium chloride (NaCl). Three groups of fungi were isolated : firstly, those isolated only at high a (aw about 0.997).secondly, those isolated at high and decreasing aw (aw 0.997 to 0.85) and finally, those isolated at only decreased aw (aw O.95 to 0.80). From these isolations, test fungi were selected to study the effects of pH, temperature, exo-enzyme production and biocide efficacy at decreased aw levels, with glycerol and NaCl as a controlling solutes. The linear extension rates of the fungi increased at all test pH values near optimum a of growth. Test fungi of the Aspergillus glaucus group were found to be most resistant to low aw. Growth and survival of vegetative and fruiting bodies at elevated temperatures were enhanced with the addition of a controlling solutes. A. flavus, A. fumigatus displayed high heat resistance and A. amstelodami, A. versicolor and Penicillium citrinum displayed low heat resistance at high aw levels and vice versa at low aw levels. Amylase, lipase and protease activities were studied at lowered aw , using modifications of the test tube method of Raute11a and Cowling. Amylase and protease production in most xerophilic fungi ceased around 0.80 aw , but lipase production in some xerophilic fungi, including A. glatlcus fungi, was up to and including 0.70 aw with g1ycero1.

The development and diffusion of industrial robots

This thesis describes the history of robots and explains the reasons for the international differences in robot diffusion, and the differences in the diffusion of various robot applications with reference to the UK. As opposed to most of the literature, diffusion is examined with an integrated and interdisciplinary perspective. Robot technology evolves from the interaction of development, supply and manufacture, adoption, and promotion. activities. Emphasis is given to the analysis of adoption, at present the most important limiting factor of robot advancement in the UK. Technical development is inferred from a comparison of surveys on equipment, and from the topics of ten years of symposia papers. This classification of papers is also used to highlight the international and institutional differences in robot development. Analysis of the growth in robot supply, manufacture, and use is made from statistics compiled. A series of interviews with users and potential users serves to illustrate the factors and implications of the adoption of different robot systems in the UK. Adoption pioneering takes place when several conditions exist: when the technology is compatible with the firm, when its advantages outweigh its disadvantages, and particularly when a climate exists which encourages the managerial involvement and the labour acceptance. The degree of compatibility (technical, methodological, organisational, and economic) and the consequences (profitability, labour impacts, and managerial effects) of different robot systems (transfer, manipulative, processing, and assembly) are determined by various aspects of manufacturing operations (complexity, automation, integration, labour tasks, and working conditions). The climate for adoption pioneering is basically determined by the performance of firms. The firms' policies on capital investment have as decisive a role in determining the profitability of robots as their total labour costs. The performance of the motor car industry and its machine builders explains, more than any other factor, the present state of robot advancement in the UK.

The development and stability analysis of a nonlinear growth model for microorganisms

A nonlinear dynamic model of microbial growth is established based on the theories of the diffusion response of thermodynamics and the chemotactic response of biology. Except for the two traditional variables, i.e. the density of bacteria and the concentration of attractant, the pH value, a crucial influencing factor to the microbial growth, is also considered in this model. The pH effect on the microbial growth is taken as a Gaussian function G0e-(f- fc)2/G1, where G0, G1 and fc are constants, f represents the pH value and fc represents the critical pH value that best fits for microbial growth. To study the effects of the reproduction rate of the bacteria and the pH value on the stability of the system, three parameters a, G0 and G1 are studied in detail, where a denotes the reproduction rate of the bacteria, G0 denotes the impacting intensity of the pH value to microbial growth and G1 denotes the bacterial adaptability to the pH value. When the effect of the pH value of the solution which microorganisms live in is ignored in the governing equations of the model, the microbial system is more stable with larger a. When the effect of the bacterial chemotaxis is ignored, the microbial system is more stable with the larger G1 and more unstable with the larger G0 for f0 > fc. However, the stability of the microbial system is almost unaffected by the variation G0 and G1 and it is always stable for f0 < fc under the assumed conditions in this paper. In the whole system model, it is more unstable with larger G1 and more stable with larger G0 for f0 < fc. The system is more stable with larger G1 and more unstable with larger G0 for f0 > fc. However, the system is more unstable with larger a for f0 < fc and the stability of the system is almost unaffected by a for f0 > fc. The results obtained in this study provide a biophysical insight into the understanding of the growth and stability behavior of microorganisms.

Precipitation casting of drug-loaded microporous PCL matrices:incorporation of progesterone by co-dissolution

Microporous, poly(ε-caprolactone) (PCL) matrices were loaded with progesterone by precipitation casting using co-solutions of PCL and progesterone in acetone. Progesterone loadings up to 32% w/w were readily achieved by increasing the drug content of the starting PCL solution. The kinetics of steroid release in PBS at 37°C over 10 days could be described effectively by a diffusional release model although the Korsmeyer-Peppas model indicated the involvement of multiple release phenomena. The diffusion rate constant (D) increased from 8 to 24 μg/mg matrix/day0.5 as the drug loading increased from 3.6 to 12.4% w/w. A total cumulative release of 75%-95% indicates the high efficiency of steroid delivery. Increasing the matrix density from 0.22 to 0.39 g/cm3, by increasing the starting PCL solution concentration, was less effective in changing drug release kinetics. Retention of anti-proliferative activity of released steroid was confirmed using cultures of breast cancer epithelial (MCF-7) cells. Progesterone released from PCL matrices into PBS at 37°C over 14 days retarded the growth of MCF-7 cells by a factor of at least 3.5 compared with progesterone-free controls. These findings recommend further investigation of precipitation-cast PCL matrices for delivery of bioactive molecules such as anti-proliferative agents from implanted, inserted or topical devices.

Delivery of the antibiotic gentamicin sulphate from precipitation cast matrices of polycaprolactone

Microporous, poly(ε-caprolactone) (PCL) matrices were loaded with the aminoglycoside antibiotic, gentamicin sulphate (GS) using the precipitation casting technique by suspension of powder in the PCL solution prior to casting. Improvements in drug loading from 1.8% to 6.7% w/w and distribution in the matrices were obtained by pre-cooling the suspension to 4°C. Gradual release of approximately 80% of the GS content occurred over 11 weeks in PBS at 37°C and low amounts of antibiotic were measured up to 20 weeks. The kinetics of release could be described effectively by the Higuchi model with the diffusion rate constant (D) increasing from of 1.7 to 5.1 μg/mg matrix/day0.5 as the drug loading increased from 1.4% to 8.3% w/w. GS-loaded PCL matrices retained anti-bacterial activity after immersion in PBS at 37°C over 14 days as demonstrated by inhibition of growth of S. epidermidis in culture. These findings recommend further investigation of precipitation-cast PCL matrices for delivery of hydrophilic molecules such as anti-bacterial agents from implanted, inserted or topical devices. © 2005 Elsevier B.V. All rights reserved.

Creative credits:a randomized controlled industrial policy experiment

This report examines the results of a pilot study, which used a method of evaluation called randomised control trials (RCTs) to see if a popular business support scheme called Creative Credits worked effectively. The pilot study, which began in Manchester in 2009, was structured so that vouchers, or 'Creative Credits', would be randomly allocated to small and medium-sized businesses applying to invest in creative projects such as developing websites, video production and creative marketing campaigns, to see if they had a real effect on innovation. The research found that the firms who were awarded Creative Credits enjoyed a short-term boost in their innovation and sales growth in the six months following completion of their creative projects. However, the positive effects were not sustained, and after 12 months there was no longer a statistically significant difference between the groups that received the credits and those that didn’t. The report argues that these results would have remained hidden using the normal evaluation methods used by government, and calls for RCTs to be used more widely when evaluating policies to support business growth.

Do foreign direct investment (FDI) and trade openness explain the disparity in ICT diffusion between Asia-Pacific and the Islamic Middle Eastern countries?

This study investigates the impact of FDI and trade openness on ICT diffusion in the Asia-Pacific and Middle East regions from 1996-2005. The results indicate that while dissimilarities exist between the economies included in this study in terms of their level of socio-economic and political development, education and the growth of GDP have had a positive impact on ICT diffusion in both regions. However, while FDI has generally had a positive and significant impact on ICT diffusion in Asia-Pacific economies, its impact on Middle Eastern economies has been detrimental. The results of this study also show that trade-openness has had, in general, a positive and significant impact on ICT diffusion. Copyright © 2010, IGI Global.

ICT innovation diffusion in small logistics service providers:an empirical study

For companies competing in highly dynamic markets, innovation is considered a fundamental component of a successful business as it allows companies to sustain profit margins, sales growth and reduce competitors’ pressures. Information and communication technology (ICT) is essential innovation enablers especially in service companies. The focus of the paper is on the analysis of the role of ICT in innovation processes of small third-party logistics service providers (3PLs). On the basis of quantitative evidence emerging from a recent survey carried out on the Italian 3PL market, the paper analyses how ICT is used to support innovation and the factors the inhibit/facilitate the usage of ICT in such companies. Implications for supply chain innovation management are derived from the research and managerial perspectives.

The effect of frequency and microstructure on corrosion fatigue crack propagation in high strength aluminium alloys

Fatigue crack growth in high strength aluminium alloy 7150 commercial plate material has been studied in both laboratory air and acidified aqueous salt solution. The aggressive aqueous environment enhanced fatigue crack growth rates by up to an order in magnitude compared to laboratory air. The enhancement in fatigue crack growth rate was accompanied by evidence of embrittlement in the crack path, involving both brittle intergranular and transgranular failure modes. Both the enhancement of fatigue crack growth rates and the extent of intergranular growth modes are dependent on cyclic frequency which, along with the absence of a similar frequency effect in a spray-formed version of the material with a significantly different grain structure, supports a mechanism of grain boundary hydrogen diffusion for intergranular corrosion fatigue crack growth. The convergence of corrosion fatigue crack growth rates at high ΔK in both spray-formed and conventional plate materials coincides with the operation of identical transgranular corrosion fatigue modes dependent on strain-controlled hydrogen diffusion ahead of the crack tip. © 1997 Acta Metallurgica Inc.

Knowledge, technological catch-up and economic growth

‘The literature on economic growth has needed for a long time a simple, but rigorous, textbook exposition of the role of knowledge in the growth process, suitable for undergraduates and policymakers. Mark Rogers’s new book provides an excellent introduction, combining clear and succinct theory with up-to-date empirical evidence on this important topic.’ – A.P. Thirlwall, University of Kent, UK Knowledge, Technological Catch-up and Economic Growth investigates the relationship between knowledge diffusion and economic growth. Using a broad definition of knowledge – encompassing technology, production skills, know-how and firm capabilities – the central argument of the book is that the extent of knowledge diffusion is an important determinant of economic growth.

The role of pinning and instability in a class of non-equilibrium growth models

We study the dynamics of a growing crystalline facet where the growth mechanism is controlled by the geometry of the local curvature. A continuum model, in (2+1) dimensions, is developed in analogy with the Kardar-Parisi-Zhang (KPZ) model is considered for the purpose. Following standard coarse graining procedures, it is shown that in the large time, long distance limit, the continuum model predicts a curvature independent KPZ phase, thereby suppressing all explicit effects of curvature and local pinning in the system, in the "perturbative" limit. A direct numerical integration of this growth equation, in 1+1 dimensions, supports this observation below a critical parametric range, above which generic instabilities, in the form of isolated pillared structures lead to deviations from standard scaling behaviour. Possibilities of controlling this instability by introducing statistically "irrelevant" (in the sense of renormalisation groups) higher ordered nonlinearities have also been discussed.

The effect of Me2SO overexposure during cryopreservation on HOS TE85 and hMSC viability, growth and quality

With the cell therapy industry continuing to grow, the ability to preserve clinical grade cells, including mesenchymal stem cells (MSCs), whilst retaining cell viability and function remains critical for the generation of off-the-shelf therapies. Cryopreservation of MSCs, using slow freezing, is an established process at lab scale. However, the cytotoxicity of cryoprotectants, like Me2SO, raises questions about the impact of prolonged cell exposure to cryoprotectant at temperatures >0 °C during processing of large cell batches for allogenic therapies prior to rapid cooling in a controlled rate freezer or in the clinic prior to administration. Here we show that exposure of human bone marrow derived MSCs to Me2SO for ≥1 h before freezing, or after thawing, degrades membrane integrity, short-term cell attachment efficiency and alters cell immunophenotype. After 2 h's exposure to Me2SO at 37 °C post-thaw, membrane integrity dropped to ∼70% and only ∼50% of cells retained the ability to adhere to tissue culture plastic. Furthermore, only 70% of the recovered MSCs retained an immunophenotype consistent with the ISCT minimal criteria after exposure. We also saw a similar loss of membrane integrity and attachment efficiency after exposing osteoblast (HOS TE85) cells to Me2SO before, and after, cryopreservation. Overall, these results show that freezing medium exposure is a critical determinant of product quality as process scale increases. Defining and reporting cell sensitivity to freezing medium exposure, both before and after cryopreservation, enables a fair judgement of how scalable a particular cryopreservation process can be, and consequently whether the therapy has commercial feasibility.