Hydrodynamic modeling of mineral wool fiber suspensions in a two-dimensional channel flow

A consequence of a loss of coolant accident is the damage of adjacent insulation materials (IM). IM may then be transported to the containment sump strainers where water is drawn into the ECCS (emergency core cooling system). Blockage of the strainers by IM lead to an increased pressure drop acting on the operating ECCS pumps. IM can also penetrate the strainers, enter the reactor coolant system and then accumulate in the reactor pressure vessel. An experimental and theoretical study that concentrates on mineral wool fiber transport in the containment sump and the ECCS is being performed. The study entails fiber generation and the assessment of fiber transport in single and multi-effect experiments. The experiments include measurement of the terminal settling velocity, the strainer pressure drop, fiber sedimentation and resuspension in a channel flow and jet flow in a rectangular tank. An integrated test facility is also operated to assess the compounded effects. Each experimental facility is used to provide data for the validation of equivalent computational fluid dynamic models. The channel flow facility allows the determination of the steady state distribution of the fibers at different flow velocities. The fibers are modeled in the Eulerian-Eulerian reference frame as spherical wetted agglomerates. The fiber agglomerate size, density, the relative viscosity of the fluid-fiber mixture and the turbulent dispersion of the fibers all affect the steady state accumulation of fibers at the channel base. In the current simulations, two fiber phases are separately considered. The particle size is kept constant while the density is modified, which affects both the terminal velocity and volume fraction. The relative viscosity is only significant at higher concentrations. The numerical model finds that the fibers accumulate at the channel base even at high velocities; therefore, modifications to the drag and turbulent dispersion forces can be made to reduce fiber accumulation.

Resonance studies of artificial earth satellites

Orbit determination from artificial satellite observations is a key process in obtaining information about the Earth and its environment. A study of the perturbations experienced by these satellites enables knowledge to be gained of the upper atmosphere, the gravity field, ocean tides, solid-Earth tides and solar radiation. The gravity field is expressed as a double infinite series of associated Legendre functions (tesseral harmonics). In contemporary global gravity field models the overall geoid is well determined. An independent check on these gravity field harmonics of a particular order may be made by analysis of satellites that pass through resonance of that order. For such satellites the perturbations of the orbital elements close to resonance are analysed to derive lumped harmonic coefficients. The orbital parameters of 1984-106A have been determined at 43 epochs, during which time the satellite was close to 14th order resonance. Analysis of the inclination and eccentricity yielded 6 lumped harmonic coefficients of order 14 whilst analysis of the mean motion yielded additional pairs of lumped harmonics of orders 14, 28 and 42, with the 14th order harmonics superseding those obtained from analysis of the inclination. This thesis concentrates in detail on the theoretical changes of a near-circular satellite orbit perturbed by the Earth's gravity field under the influence of minimal air-drag whilst in resonance with the Earth. The satellite 1984-106A experienced the interesting property of being temporarily trapped with respect to a secondary resonance parameter due to the low air-drag in 1987. This prompted the theoretical investigation of such a phenomenon. Expressions obtained for the resonance parameter led to the determination of 8 lumped harmonic coefficients, coincidental to those already obtained. All the derived lumped harmonic values arc used to test the accuracy of contemporary gravity field models and the underlying theory in this thesis.

Precise orbit determination and analysis from satellite altimetry and laser ranging

For optimum utilization of satellite-borne instrumentation, it is necessary to know precisely the orbital position of the spacecraft. The aim of this thesis is therefore two-fold - firstly to derive precise orbits with particular emphasis placed on the altimetric satellite SEASAT and secondly, to utilize the precise orbits, to improve upon atmospheric density determinations for satellite drag modelling purposes. Part one of the thesis, on precise orbit determinations, is particularly concerned with the tracking data - satellite laser ranging, altimetry and crossover height differences - and how this data can be used to analyse errors in the orbit, the geoid and sea-surface topography. The outcome of this analysis is the determination of a low degree and order model for sea surface topography. Part two, on the other hand, mainly concentrates on using the laser data to analyse and improve upon current atmospheric density models. In particular, the modelling of density changes associated with geomagnetic disturbances comes under scrutiny in this section. By introducing persistence modelling of a geomagnetic event and solving for certain geomagnetic parameters, a new density model is derived which performs significantly better than the state-of-the-art models over periods of severe geomagnetic storms at SEASAT heights. This is independently verified by application of the derived model to STARLETTE orbit determinations.

The interaction between master production scheduling and detailed capacity requirements planning : closing the loop in manufacturing resource planning (MRPII) systems

The widespread implementation of Manufacturing Resource Planning (MRPII) systems in this country and abroad and the reported dissatisfaction with their use formed the initial basis of this piece of research which concentrates on the fundamental theory and design of the Closed Loop MRPII system itself. The dissertation concentrates on two key aspects namely; how Master Production Scheduling is carried out in differing business environments and how well the `closing of the loop' operates by checking the capcity requirements of the different levels of plans within an organisation. The main hypothesis which is tested is that in U.K. manufacturing industry, resource checks are either not being carried out satisfactorily or they are not being fed back to the appropriate plan in a timely fashion. The research methodology employed involved initial detailed investigations into Master Scheduling and capacity planning in eight diverse manufacturing companies. This was followed by a nationwide survey of users in 349 companies, a survey of all the major suppliers of Production Management software in the U.K. and an analysis of the facilities offered by current software packages. The main conclusion which is drawn is that the hypothesis is proved in the majority of companies in that only just over 50% of companies are attempting Resource and Capacity Planning and only 20% are successfully feeding back CRP information to `close the loop'. Various causative factors are put forward and remedies are suggested.

Molecular biology and biochemistry of brain tumours

ßElucidating some molecular mechanisms and biochemistry of brain tumours is an important step towards the development of adjuvant medical therapies. The present study concentrates on cholecystokinin (CCK), a gut-brain peptide that has been described to be able to induce mitosis of rat gliomas as well as hormone secretion by the anterior pituitary, via the CCK-B receptor. The significance of a polymorphism in the growth hormone releasing hormone (GHRH) receptor (GHRH-R) gene was also determined. Finally, defects in the ß-catenin gene, an important component of the developmental pathway, in a sub-set of craniopharyngiomas were investigated. Reverse transcription-polymerase chain reaction (RT-PCR), restriction digestion analysis and direct sequencing demonstrated expression of CCK peptide itself and its A and B receptors by human gliomas, meningiomas and pituitary tumours. CCK peptides stimulated growth of cultured gliomas and meningiomas as well as in vitro hormone secretion [growth hormone (GH), luteinizing hormone (LH) and follicle stimulating hormone (FSH)] by human pituitary tumours. These biological effects were reduced or abolished by CCK antagonists. In addition, an antibody to CCK reduced mitosis by gliomas and meningiomas, and the same antibody inhibited hormone secretion by cultured human pituitary tumours. CCK peptides stimulated phosphatidylinositol (PI) hydrolysis, indicating coupling of the CCK receptors to phopsholipase C. Cyclic AMP was unaffected. In addition, caspase-3 activity was significantly and markedly increased, whilst proteasome activity was decreased. Taken together, these results may indicate an autocrine/paracrine role of CCK in the control of growth and/or functioning of gliomas, meningiomas and pituitary tumours. Primer induced restriction analysis (PIRA) of a rarer and alternative polymorphism in the GHRH-R receptor, in which Thr replaces Ala at codon 57, in human GH-secreting pituitary tumours was investigated. Whilst the rarer form correlated with an increased response of the pituitary cells to GHRH in vitro, allele distribution studies revealed that it is unlikely that the polymorphism contributes to increased risk of developing GH-secreting tumours and therefore acromegaly. Further findings of this study, using PCR and direct sequencing, were the demonstration of an association between b-catenin gene alterations and craniopharyngiomas of the adamantinomatous type. Since this gene product is involved with development, these results suggest that p-catenin mutations may contribute to the initiation and subsequent growth of congenital adamantinomatous craniopharyngiomas.

An evaluation of thermal plasmas in pyrometallurgy

The development of reliable, high powered plasma generators has resulted in many plasma processes being proposed as alternatives to existing pyrometallurgical technologies. This work evaluates the advantages and disadvantages of plasma systems by reviewing plasma generators, their integration with reactors and the process economics. Many plasma systems were shown to be technically and economically superior to existing technologies, but some of the plasma system advantages quoted in the literature were found to be impractical because of other system constraints. Process applications were limited by the power inputs available from plasma generators compared to AC electric furnaces. A series of trials were conducted where chromite and steelplant baghouse dusts were smelted in the Tetronics' 2.0 MW transferred arc/open bath reactor to confirm the operating characteristics of the plasma system and its economics. Chromite smelting was technical superior to submerged arc furnace technology, but the economics were unfavourable because of the limited power available from the water-cooled plasma torch and the high electrical energy consumption. A DC graphite electrode plasma furnace using preheated and prereduced chromite concentrates will compete economically with the submerged arc furnace. Ni, Cr and Mo were economically recovered from high alloy content steelplant dusts for recycling. Five Electric Arc Furnace dusts were smelted to produce a non-toxic residue and recover the contained zinc to an enriched zinc oxide product for recycling. It should be possible to condense the zinc vapour directly in a zinc splash condenser to increase the value of the product. Because of the limited power available from plasma generators, plasma processes will be most suitable for treating high and medium value materials such as Au, Pt, Mo, Ni, Ti, V, Cr etc at small production rates, heating metals in tundishes and ladles and remelting superalloy scrap. The treatment of environmentally hazardous waste materials is a particularly interesting application because of the additional financial incentives. Non-transferred arc plasma generators will be used for air and gas preheating in blast furnaces to reduce metallurgical coke consumptions.

State intervention in technology in the post war years: case studies in technology policy

This thesis is concerned with the means by which the state in Britain has attempted to influence the technological development of private industry in the period 1945-1979. Particular emphasis is laid on assessing the abilities of technology policy measures to promote innovation. With that objective, the innovation literature is selectively reviewed to draw up an analytical framework to evaluate the innovation content of policy (Chapter 2). Technology policy is taken to consist of the specific measures utilised by government and its agents that affect the technological behaviour of firms. The broad sweep of policy during the period under consideration is described in Chapter 3 which concentrates on elucidating its institutional structure and the activities of the bodies involved. The empirical core of the thesis consists of three parallel case studies of policy toward the computer, machine tool and textile machinery industries (Chapters 4-6). The studies provide detailed historical accounts of the development and composition of policy, relating it to its specific institutional and industrial contexts. Each reveals a different pattern and level of state intervention. The thesis concludes with a comparative review of the findings of the case studies within a discussion centred on the arguments presented in Chapter 2. Topics arising include the state's differential support for the range of activities involved in innovation, the location of state-funded R&D, the encouragement of supplier-user contact, and the difficulties raised in adoption and diffusion.

Computer aided process planning (CAPP) for flat rolling of copper alloys

The manufacture of copper alloy flat rolled metals involves hot and cold rolling operations, together with annealing and other secondary processes, to transform castings (mainly slabs and cakes) into such shapes as strip, plate, sheet, etc. Production is mainly to customer orders in a wide range of specifications for dimensions and properties. However, order quantities are often small and so process planning plays an important role in this industry. Much research work has been done in the past in relation to the technology of flat rolling and the details of the operations, however, there is little or no evidence of any research in the planning of processes for this type of manufacture. Practical observation in a number of rolling mills has established the type of manual process planning traditionally used in this industry. This manual approach, however, has inherent drawbacks, being particularly dependent on the individual planners who gain their knowledge over a long span of practical experience. The introduction of the retrieval CAPP approach to this industry was a first step to reduce these problems. But this could not provide a long-term answer because of the need for an experienced planner to supervise generation of any plan. It also fails to take account of the dynamic nature of the parameters involved in the planning, such as the availability of resources, operation conditions and variations in the costs. The other alternative is the use of a generative approach to planning in the rolling mill context. In this thesis, generative methods are developed for the selection of optimal routes for single orders and then for batches of orders, bearing in mind equipment restrictions, production costs and material yield. The batch order process planning involves the use of a special cluster analysis algorithm for optimal grouping of the orders. This research concentrates on cold-rolling operations. A prototype model of the proposed CAPP system, including both single order and batch order planning options, has been developed and tested on real order data in the industry. The results were satisfactory and compared very favourably with the existing manual and retrieval methods.

An experimental analysis of operating conditions in cold roll-forming

A detailed literature survey confirmed cold roll-forming to be a complex and little understood process. In spite of its growing value, the process remains largely un-automated with few principles used in set-up of the rolling mill. This work concentrates on experimental investigations of operating conditions in order to gain a scientific understanding of the process. The operating conditions are; inter-pass distance, roll load, roll speed, horizontal roll alignment. Fifty tests have been carried out under varied operating conditions, measuring section quality and longitudinal straining to give a picture of bending. A channel section was chosen for its simplicity and compatibility with previous work. Quality measurements were measured in terms of vertical bow, twist and cross-sectional geometric accuracy, and a complete method of classifying quality has been devised. The longitudinal strain profile was recorded, by the use of strain gauges attached to the strip surface at five locations. Parameter control is shown to be important in allowing consistency in section quality. At present rolling mills are constructed with large tolerances on operating conditions. By reduction of the variability in parameters, section consistency is maintained and mill down-time is reduced. Roll load, alignment and differential roll speed are all shown to affect quality, and can be used to control quality. Set-up time is reduced by improving the design of the mill so that parameter values can be measured and set, without the need for judgment by eye. Values of parameters can be guided by models of the process, although elements of experience are still unavoidable. Despite increased parameter control, section quality is variable, if only due to variability in strip material properties. Parameters must therefore be changed during rolling. Ideally this can take place by closed-loop feedback control. Future work lies in overcoming the problems connected with this control.

Foreign direct investment and corruption

In the last few decades, the world has witnessed an enormous growth in the volume of foreign direct investment (FDI). The global stock of FDI reached US$ 7.5 trillion in 2003 and accounted for 11% of world Gross Domestic Product, up from 7% in 1990. The sales of multinational enterprises at around US$ 19 trillion were more than double the level of world exports. Substantial FDI inflows went into transition countries. Inflows into one of the region's largest recipient, the Russian Federation, almost doubled, enabling Russia to become one of the five top FDI destinations in 2005-2006. FDI inflows in Russia have increased almost threefold from 13.6% in 2003 to 35% in 2007. In 2003, these flows were twice greater than those into China; whilst in 2007 they were six times larger. Russia's FDI inflows were also about 2.5 times greater than those of Brazil. Efficient government institutions are argued by many economists to foster FDI and growth as a result. However, the magnitude of this effect has yet to be measured. This thesis takes a Political Economy approach to explore, empirically, the potential impact of malfunctioning governmental institutions, proxied by three indices of perceived corruption, on FDI stocks accumulation/distribution within Russia over the period of 2002-2004. Using a regional data-set it concentrates on three areas relating to FDI. Firstly, it considers the significance, the size and the sign of the impact of perceived corruption on accumulation of FDI stocks within Russia. Secondly, it quantifies the impact of perceived corruption on the volume of FDI stocks simultaneously estimating the impact of the investment in public capital such as telecommunications and transportation networks on FDI in the presence of corruption. In particular, it addresses the question whether more corrupt regions in Russia are also those that could have accumulated more of FDI stocks, and investigates whether those 'more corrupt' regions would have had lower level of public capital investment. Finally, it examines whether decentralisation increases or decreases corruption and whether a larger extent of decentralisation has a positive or negative impact on FDI (stocks). The results of three studies are as follows. Firstly, along with market potential, corruption is found to be one of the key factors in explaining FDI distribution within Russia between 2002 and 2004. Secondly, corruption on average is found to be related to FDI positively suggesting that it may act as speed money: to save their time foreign direct investors might be willing to bribe the regional authorities so to move in front of the bureaucratic lines. Thirdly, although when corruption is controlled for, the impact of the latter on unobservable FDI is found to be on average positive, no association between FDI and public investment is observed with the only exception of transportation infrastructure (i.e., railway). The results might suggest therefore that it is possible that not only regions with high levels of perceived corruption attract more FDI but also that expansions in public capital investments are not accompanied by an increase of the volume of FDI (stocks) in regions with high levels of corruption. This casts some doubt on the productivity of the investment in public capital in these regions as it might be that bureaucrats may prefer to use these infrastructural projects for rent extraction. Finally, we find decentralisation to have a significant and positive impact on both FDI stock accumulation and corruption, suggesting that local governments may spend more on public goods to make the area more attractive to foreign investors but at the same time they may be interested into extracting rents from foreign investors. These results support the idea that the regulation of FDI is associated with and facilitated by a larger public sector, which distorts competition and introduces opportunities for rent-seeking by particular economic and political factors.

Primary health care management in Nigeria

This research sets out to assess if the PHC system in rural Nigeria is effective by testing the research hypothesis: `PHC can be effective if and only if the Health Care Delivery System matches the attitudes and expectations of the Community'. The field surveys to accomplish this task were carried out in IBO, YORUBA, and HAUSA rural communities. A variety of techniques have been used as Research Methodology and these include questionnaires, interviews and personal observations of events in the rural community. This thesis embraces three main parts. Part I traces the socio-cultural aspects of PHC in rural Nigeria, describes PHC management activities in Nigeria and the practical problems inherent in the system. Part II describes various theoretical and practical research techniques used for the study and concentrates on the field work programme, data analysis and the research hypothesis-testing. Part III focusses on general strategies to improve PHC system in Nigeria to make it more effective. The research contributions to knowledge and the summary of main conclusions of the study are highlighted in this part also. Based on testing and exploring the research hypothesis as stated above, some conclusions have been arrived at, which suggested that PHC in rural Nigeria is ineffective as revealed in people's low opinions of the system and dissatisfaction with PHC services. Many people had expressed the view that they could not obtain health care services in time, at a cost they could afford and in a manner acceptable to them. Following the conclusions, some alternative ways to implement PHC programmes in rural Nigeria have been put forward to improve and make the Nigerian PHC system more effective.

Aspects of design for a spare parts provisioning system

This thesis describes an investigation by the author into the spares operation of compare BroomWade Ltd. Whilst the complete system, including the warehousing and distribution functions, was investigated, the thesis concentrates on the provisioning aspect of the spares supply problem. Analysis of the historical data showed the presence of significant fluctuations in all the measures of system performance. Two Industrial Dynamics simulation models were developed to study this phenomena. The models showed that any fluctuation in end customer demand would be amplified as it passed through the distributor and warehouse stock control systems. The evidence from the historical data available supported this view of the system's operation. The models were utilised to determine which parts of the total system could be expected to exert a critical influence on its performance. The lead time parameters of the supply sector were found to be critical and further study showed that the manner in which the lead time changed with work in progress levels was also an important factor. The problem therefore resolved into the design of a spares manufacturing system. Which exhibited the appropriate dynamic performance characteristics. The gross level of entity presentation, inherent in the Industrial Dynamics methodology, was found to limit the value of these models in the development of detail design proposals. Accordingly, an interacting job shop simulation package was developed to allow detailed evaluation of organisational factors on the performance characteristics of a manufacturing system. The package was used to develop a design for a pilot spares production unit. The need for a manufacturing system to perform successfully under conditions of fluctuating demand is not limited to the spares field. Thus, although the spares exercise provides an example of the approach, the concepts and techniques developed can be considered to have broad application throughout batch manufacturing industry.

A survey of urban open space using colour infra-red aerial photographs

There has been a dramatic change in the U.K. government policy regarding the establishment of new towns. The emphasis is now on the redevelopment of existing cities rather than on building new ones. This has created an urgent need to carry out detailed surveys and inventories of many aspects of urban land use in metropolitan areas: this study concentrates on just one aspect - urban open space. In the first stage a comparison was made between 1:10,000 scale black and white and 1:10,000 scale colour infra-red aerial photographs, to compare the type and amount of open space information which could be obtained from these two sources. The advantages of using colour infra-red photography were clearly demonstrated in this comparison. The second stage was the use of colour infra-red photography as the sole source of data to survey and map the urban open space of a sample area in Merseyside Metropolitan County. This sample area comprised eleven 1/4km2 squares, on each of which a 20m x 20m grid cell was placed to record, directly from the photography, 625 sets of data. Each set of data recorded the type and amount of open space, its surface cover, maintenance status and management. The data recorded were fed into a computer and a suite of programs was developed to provide output in both computer map and statistical form, for each of the eleven -1/4km2 -sample areas. The third stage involved a comparison of open space data with socio-economic status. Merseyside County Planning Authority had previously conducted a socio-economic survey of the county, and this information was used to identify ' the socio-economic status of the population in the eleven ilkm2 areas of this project. This comparison revealed many interesting and useful relationships between the provision of urban open space and socio-economic status.

The application of artificial neural networks to the interpretation and classification of freshwater benthic invertebrate communities

This thesis presents a thorough and principled investigation into the application of artificial neural networks to the biological monitoring of freshwater. It contains original ideas on the classification and interpretation of benthic macroinvertebrates, and aims to demonstrate their superiority over the biotic systems currently used in the UK to report river water quality. The conceptual basis of a new biological classification system is described, and a full review and analysis of a number of river data sets is presented. The biological classification is compared to the common biotic systems using data from the Upper Trent catchment. This data contained 292 expertly classified invertebrate samples identified to mixed taxonomic levels. The neural network experimental work concentrates on the classification of the invertebrate samples into biological class, where only a subset of the sample is used to form the classification. Other experimentation is conducted into the identification of novel input samples, the classification of samples from different biotopes and the use of prior information in the neural network models. The biological classification is shown to provide an intuitive interpretation of a graphical representation, generated without reference to the class labels, of the Upper Trent data. The selection of key indicator taxa is considered using three different approaches; one novel, one from information theory and one from classical statistical methods. Good indicators of quality class based on these analyses are found to be in good agreement with those chosen by a domain expert. The change in information associated with different levels of identification and enumeration of taxa is quantified. The feasibility of using neural network classifiers and predictors to develop numeric criteria for the biological assessment of sediment contamination in the Great Lakes is also investigated.

Effect of processing on sulphur antioxidants in polyolefins

The effect of processing on the antioxidant activity of sulphur-containing compounds, with particular reference to nickel dialkyldithiophosphates and their corresponding di sulphides, were studied in polyolefins under melt, thermal and photo-oxidative conditions. These compounds were evaluated both at low (normal) and high (concentrates) concentrations. In general, the dithiophosphates were found to be very efficient melt stabilisers at normal concentrtion levels, and compare quite favourably with the best commercially available systems. The nickel dithiophosphates were also found to be very efficient thermal stabilisers for polyolefins, but their activity is highly dependent on the alkyl substituent in the molecule. The corresponding disulphides on the other hand showed very little activity under thermal oxidative conditions, and this was attributed to their inefficiency in scavenging alkyl peroxyl radicals since both compounds possess similar peroxidolytic activity. Furthermore, the nickel dithiophosphates were found to be excellent photo stabilisers for mildly-processed polyolefins while the corresponding disulphides only offer slight protection to the polymer. Oxidative processing of the disulphide, however, results in a dramatic improvement in their photo antioxidant activity. Thionophospho-ric acid, a major oxidation product of dithiophosphates, was also shown to have photo antioxidant activity similar to that of the disulphides. A combination of a U.V. absorber with the nickel complex and/or the disulphide resulted in a synergistic stabiliser system which was further augmented by oxidative processing. Moreover, the dilute analogues of such multicomponent stabiliser concentrates also showed excellent melt, thermal and photo-stabilising activity. The mechanistic studies carried out on the nickel complex and the corresponding disulphide clearly identified the thionophosphoric acid a a major transformation product although various triesters were formed as reaction intermediates. The mechanisms of the antioxidant action of the dithiophosphates, which is believed to involve a cyclical process similar to that shown for simple alkyl sulphides and nitroxyls, are discussed.