A micro gas turbines for UK domestic combined heat and power

Various micro-radial compressor configurations were investigated using one-dimensional meanline and computational fluid dynamics (CFD) techniques for use in a micro gas turbine (MGT) domestic combined heat and power (DCHP) application. Blade backsweep, shaft speed, and blade height were varied at a constant pressure ratio. Shaft speeds were limited to 220 000 r/min, to enable the use of a turbocharger bearing platform. Off-design compressor performance was established and used to determine the MGT performance envelope; this in turn was used to assess potential cost and environmental savings in a heat-led DCHP operating scenario within the target market of a detached family home. A low target-stage pressure ratio provided an opportunity to reduce diffusion within the impeller. Critically for DCHP, this produced very regular flow, which improved impeller performance for a wider operating envelope. The best performing impeller was a low-speed, 170 000 r/min, low-backsweep, 15° configuration producing 71.76 per cent stage efficiency at a pressure ratio of 2.20. This produced an MGT design point system efficiency of 14.85 per cent at 993 W, matching prime movers in the latest commercial DCHP units. Cost and CO2 savings were 10.7 per cent and 6.3 per cent, respectively, for annual power demands of 17.4 MWht and 6.1 MWhe compared to a standard condensing boiler (with grid) installation. The maximum cost saving (on design point) was 14.2 per cent for annual power demands of 22.62 MWht and 6.1 MWhe corresponding to an 8.1 per cent CO2 saving. When sizing, maximum savings were found with larger heat demands. When sized, maximum savings could be made by encouraging more electricity export either by reducing household electricity consumption or by increasing machine efficiency.

BTX extraction by sulfolane in a mixer-settler cascade

The literature relating to the extraction of the aromatics, benzene, toluene and xylene (BTX) using different commercial solvents, and to mixer-settler design and performance, has been reviewed. Liquid-liquid equilibria of the ternary systems: hexane-benzene-sulfolane, n-heptane-toluene-sulfolane, and octane-xylene-sulfolane were determined experimentally at temperatures of 30oC, 35oC, and 40oC. The work was then extended to a multicomponent system. The data were correlated by using Hand's method and were found to be in a good agreement with theoretical predictions using the UNIFAC method. A study was made of the performance of a 10-stage laboratory mixer-settler cascade for the extraction of BTX from a synthetic reformate utilizing sulfolane as a solvent. Murphree stage efficiency decreased with stage number but 99% extraction was achievable within 4 stages. The effects of temperature, phase ratio, and agitator speed were investigated. The efficiency increased with agitator speed but > 1050 rpm resulted in secondary haze formation. An optimum temperature of 30oC was selected from the phase equilibria; the optimum solvent: feed ratio was 3:1 for 4 stages. The experimental overall mass transfer coefficients were compared with those predicted from single drop correlations and were in all cases greater, by a factor of 1.5 to 3, due to the surface renewal associated with drop break-up and coalescence promoted by agitation. A similar investigation was performed using real reformate from the Kuwait Oil Company. The phase ratios were in the range 0.5 to 1 to 3.25 to 1, the agitator speed 1050 rpm, and the operating temperature 30oC. A maximum recovery of 99% aromatics was achieved in 4 stages at a phase ratio of 3.25 to 1. A backflow model was extended to simulate conditions in the mixer-settler cascade with this multicomponent system. Overall mass transfer coefficients were estimated by obtaining the best fit between experimental and predicted concentration profiles. They were up to 10% greater than those with the synthetic feed but close agreement was not possible because the distribution coefficient and phase ratio varied with stage number. Sulfolane was demonstrated to be an excellent solvent for BTX recovery and a mixer-settler cascade was concluded to be a technically viable alternative to agitated columns for this process.

Hydrodynamics and mass transfer studies in a scheibel extractor

A 10 cm diameter four-stage Scheibel column with dispersed phase wetted packing sections has been constructed to study the hydrodynamics and mass transfer using the system toluene-acetone-water. The literature pertaining to the above extractor has been examined and the important phenomena such as droplet break-up and coalescence, mass transfer and backmixing have been reviewed. A critical analysis of the backmixing or axial mixing models and the corresponding techniques for parameter estimation was applied and an optimization technique based on Marquardt's algorithm was implemented. A single phase sampling technique was developed to estimate the acetone concentration profile in both phases along the column. Column flooding characteristics were investigated under various operating conditions and it was found that, when the impellers were located at about DI/5cm from the upper surface of the pads, the limiting flow rates increased with impeller speed. This unusual behaviour was explained in terms of the pumping effect created by the turbine impellers. Correlations were developed to predict Sauter mean drop diameters. A five-cell with backflow model was used to estimate the column performance (stage efficiency) and phases non-ideality (backflow parameters). Overall mass transfer coefficients were computed using the above model and compared with those calculated using the correlations based on single drop mechanism.

The determinants of firms' performance:can finance constraints improve technical efficiency?

This paper analyses the mechanisms through which binding finance constraints can induce debt-constrained firms to improve technical efficiency to guarantee positive profits. This hypothesis is tested on a sample of firms belonging to the Italian manufacturing. Technical efficiency scores are computed by estimating parametric production frontiers using the one stage approach as in Battese and Coelli [Battese, G., Coelli, T., 1995. A model for technical efficiency effects in a stochastic frontier production function for panel data. Empirical Economics 20, 325-332]. The results support the hypothesis that a restriction in the availability of financial resources can affect positively efficiency. © 2004 Elsevier B.V. All rights reserved.

Organizational capital, product market competition and technical efficiency in Italian cooperatives

This paper tries to identify under which conditions increasing market competition may help cooperatives to improve technical efficiency to guarantee positive profits. This hypothesis is first formalized in a partial equilibrium framework and then is tested on a sample of Italian conventional and cooperative firms, using frontier analysis. Technical efficiency indexes are computed by using the one-stage approach as suggested by Battese and Coelli (1995), where proxies for competition are introduced as determinants of efficiency, along with other exogenous factors accounting for the firms’ heterogeneity. However, the overall impact of increasing competition on efficiency is negative.

The ecology of percolating filters containing a plastic filter medium in relation to their efficiency in The treatment of domestic sewage

The suitability of a new plastic supporting medium for biofiltration was tested over a three year period. Tests were carried out on the stability, surface properties, mechanical strength, and dimensions of the medium. There was no evidence to suggest that the medium was deficient in any of these respects. The specific surface (320m2m-3) and the voidage (94%) of the new medium are unlike any other used in bio-filtration and a pilot plant containing two filters was built to observe its effects on ecology and performance. Performance was estimated by chemical analysis and ecology studied by film examination and fauna counts. A system of removable sampling baskets was designed to enable samples to be obtained from two intermediate depths of filter. One of the major operating problems of percolating filters is excessive accumulation of film. The amount of film is influenced by hydraulic and organic load and each filter was run at a different loading. One was operated at 1.2m3m-3day-1 (DOD load 0.24kgm-3day-1) judged at the time to be the lowest filtration rate to offer advantages over conventional media. The other filter was operated at more than twice this loading (2.4m3m-3day-lBOD load 0.55kgm-3day-1) giving a roughly 2.5x and 6x the conventional loadings recommended for a Royal Commission effluent. The amount of film in each filter was normally low (0.05-3kgm(3 as volatile solids) and did not affect efficiency. The evidence collected during the study indicated that the ecology of the filters was normal when compared with the data obtained from the literature relating to filters with mineral media. There were indications that full ecological stability was yet to be reached and this was affecting the efficiency of the filters. The lower rate filter produced an average 87% BOD removal giving a consistent Royal Commission effluent during the summer months. The higher rate filter produced a mean 83% BOD removal but at no stage a consistent Royal Commission effluent. From the data on ecology and performance the filters resembled conventional filters rather than high rate filters.

Development of techniques to predict production line efficiency

This industrial based research project was undertaken for British Leyland and arose as a result of poor system efficiency on the Maxi and Marina vehicle body build lines. The major factors in the deterioration of system efficiency were identified as: a) The introduction of a 'Gateline' system of vehicle body build. b) The degeneration of a newly introduced measured daywork payment scheme. By relating the conclusions of past work on payment systems to the situation at Cowley, it was concluded that a combination of poor industrial relations and a lack of managerial control had caused the measured daywork scheme to degenerate into a straightforward payment for time at work. This ellminated the monetary incentive to achieve schedule with the consequence that both inefficiency and operating costs increased. To analyse further the cause of inefficiency, a study of Marina gateline stoppage logs was carried out. This revealed that poor system efficiency on the gateline was caused more by the nature of its design than poor reliability on individual items of' plant. The consideration given to system efficiency at the design stage was found to be negligible, the main obstacles being: a) A lack of understanding pertaining to the influence of certain design factors on the efficiency of a production line. b) The absence of data and techniques to predict system efficiency at the design stage. To remedy this situation, a computer simulation study of' the design factors was carried out from which relationships with system efficiency were established and empirical efficiency equations developed. Sets of tables were compiled from the equations and efficiency data relevant to vehicle body building established from the gateline stoppage logs. Computer simulation, the equations and the tables,when used in conjunction. with good efficiency data, are shown to be accurate methods of predicting production line system.efficiency.

HTHP syngas cleaning concept of two stage biomass gasification for FT synthesis

The EU intends to increase the fraction of fuels from biogenic energy sources from 2% in 2005 to 8% in 2020. This means a minimum of 30 million TOE/a of fuels from biomass. This makes technical-scale generation of syngas from high-grade biomass, e.g. straw, hay, bark, or paper/cardboard waste, and the production of synthetic fuels by Fischer-Tropsch (FT) synthesis highly attractive. The BTL concept (Biomass to Liquids) of the Karlsruhe Research Center, labeled bioliq, focuses on this challenge by locally concentrating the biomass energy content by fast pyrolysis in a coke/oil slurry followed by slurry conversion to syngas in a central entrained flow gasifier at 1200C and pressures above 4MPa. FT synthesis generates intermediate products for synthetic fuels. To prevent the sensitive catalysts from being poisoned the syngas must be free of tar and particulates. Trace concentrations of H2S, COS, CS2, HCl, NH3, and HCN must be on the order of a few ppb. Moreover, maximum conversion efficiency will be achieved by cleaning the gas above the synthesis conditions. (T>350C, P>4MPa). The concept of an innovative dry HTHP syngas cleaning process is presented. Based on HT particle filtration and suitable sorption and catalysis processes for the relevant contaminants, an overall concept will be derived, which leads to a syngas quality required for FT synthesis in only two combined stages. Results of filtration experiments on a pilot scale are presented. The influence of temperature on the separation and conversion, respectively, of particulates and gaseous contaminants is discussed on the basis of experimental results obtained on a laboratory and pilot scale. Extensive studies of this concept are performed in a scientific network comprising the Karlsruhe Research Center and five universities; funding is provided by the Helmholtz Association of National Research Centers in Germany.

Evaluating productive efficiency:comparative study of commercial banks in Gulf countries

Financial institutes are an integral part of any modern economy. In the 1970s and 1980s, Gulf Cooperation Council (GCC) countries made significant progress in financial deepening and in building a modern financial infrastructure. This study aims to evaluate the performance (efficiency) of financial institutes (banking sector) in GCC countries. Since, the selected variables include negative data for some banks and positive for others, and the available evaluation methods are not helpful in this case, so we developed a Semi Oriented Radial Model to perform this evaluation. Furthermore, since the SORM evaluation result provides a limited information for any decision maker (bankers, investors, etc...), we proposed a second stage analysis using classification and regression (C&R) method to get further results combining SORM results with other environmental data (Financial, economical and political) to set rules for the efficient banks, hence, the results will be useful for bankers in order to improve their bank performance and to the investors, maximize their returns. Mainly there are two approaches to evaluate the performance of Decision Making Units (DMUs), under each of them there are different methods with different assumptions. Parametric approach is based on the econometric regression theory and nonparametric approach is based on a mathematical linear programming theory. Under the nonparametric approaches, there are two methods: Data Envelopment Analysis (DEA) and Free Disposal Hull (FDH). While there are three methods under the parametric approach: Stochastic Frontier Analysis (SFA); Thick Frontier Analysis (TFA) and Distribution-Free Analysis (DFA). The result shows that DEA and SFA are the most applicable methods in banking sector, but DEA is seem to be most popular between researchers. However DEA as SFA still facing many challenges, one of these challenges is how to deal with negative data, since it requires the assumption that all the input and output values are non-negative, while in many applications negative outputs could appear e.g. losses in contrast with profit. Although there are few developed Models under DEA to deal with negative data but we believe that each of them has it is own limitations, therefore we developed a Semi-Oriented-Radial-Model (SORM) that could handle the negativity issue in DEA. The application result using SORM shows that the overall performance of GCC banking is relatively high (85.6%). Although, the efficiency score is fluctuated over the study period (1998-2007) due to the second Gulf War and to the international financial crisis, but still higher than the efficiency score of their counterpart in other countries. Banks operating in Saudi Arabia seem to be the highest efficient banks followed by UAE, Omani and Bahraini banks, while banks operating in Qatar and Kuwait seem to be the lowest efficient banks; this is because these two countries are the most affected country in the second Gulf War. Also, the result shows that there is no statistical relationship between the operating style (Islamic or Conventional) and bank efficiency. Even though there is no statistical differences due to the operational style, but Islamic bank seem to be more efficient than the Conventional bank, since on average their efficiency score is 86.33% compare to 85.38% for Conventional banks. Furthermore, the Islamic banks seem to be more affected by the political crisis (second Gulf War), whereas Conventional banks seem to be more affected by the financial crisis.

Public sector efficiency, foreign aid and small island development states

This paper examines the efficiency of public sector expenditures and foreign aid at achieving social sector outcomes in Small Island Developing States (SIDS). Efficiency is estimated using a Stochastic Production Function (SPF) approach and panel data since 1990. A second stage of the analysis examines the determinants of efficiency. Results indicate that the efficiency of aid and public sectors at improving life expectancy has deteriorated during the 1990s but efficiency at improving school enrolments has increased. Higher levels of governance are associated with higher efficiency. There is also evidence to suggest that efficiency is lower in SIDS, as well as in Sub-Saharan Africa.

A non-parametric data envelopment analysis approach for improving energy efficiency of grape production

Grape is one of the world's largest fruit crops with approximately 67.5 million tonnes produced each year and energy is an important element in modern grape productions as it heavily depends on fossil and other energy resources. Efficient use of these energies is a necessary step toward reducing environmental hazards, preventing destruction of natural resources and ensuring agricultural sustainability. Hence, identifying excessive use of energy as well as reducing energy resources is the main focus of this paper to optimize energy consumption in grape production.In this study we use a two-stage methodology to find the association of energy efficiency and performance explained by farmers' specific characteristics. In the first stage a non-parametric Data Envelopment Analysis is used to model efficiencies as an explicit function of human labor, machinery, chemicals, FYM (farmyard manure), diesel fuel, electricity and water for irrigation energies. In the second step, farm specific variables such as farmers' age, gender, level of education and agricultural experience are used in a Tobit regression framework to explain how these factors influence efficiency of grape farming.The result of the first stage shows substantial inefficiency between the grape producers in the studied area while the second stage shows that the main difference between efficient and inefficient farmers was in the use of chemicals, diesel fuel and water for irrigation. The use of chemicals such as insecticides, herbicides and fungicides were considerably less than inefficient ones. The results revealed that the more educated farmers are more energy efficient in comparison with their less educated counterparts. © 2013.

Hospital performance:efficiency or quality? Can we have both with IT?

The influence of IT investment on hospital efficiency and quality are of great interest to healthcare executives as well as insurers. Few studies have examined how IT investments influence both efficiency and quality or whether there is an optimal IT investment level that influences both in the desired direction. Decision makers in healthcare wonder if there are tradeoffs between their pursuit of hospital operational efficiency and quality. Our study involving a 2-stage double bootstrap DEA analysis of 187 US hospitals over 2. years found direct effects of IT investment upon service quality and a moderating effect of quality upon operational efficiency. Further, our findings indicate a U-shaped relationship between IT investments and operational efficiency suggesting that IT investments have diminishing returns beyond a certain point.

Social and financial efficiency of Islamic microfinance institutions:a Data Envelopment Analysis application

Microfinance has been developed as alternative solution for global poverty alleviation effort in the last 30 years. Microfinance institution (MFI) has unique characteristic wherein they face double bottom line objectives of outreach to the poor and financial sustainability. This study proposes a two-stage analysis to measure Islamic Microfinance institutions (IMFIs) performance by comparing them to conventional MFIs. First, we develop a Data Envelopment Analysis (DEA) framework to measure MFIs' efficiency in its double bottom line objectives, i.e. in terms of social and financial efficiency. In the second stage non-parametric tests are used to compare the performance and identify factors that contribute to the efficiency of IMFIs and MFIs.

Maximising the efficiency of logistics operations with radio frequency identification technology

Radio frequency identification (RFID) technology has gained increasing popularity in businesses to improve operational efficiency and maximise costs saving. However, there is a gap in the literature exploring the enhanced use of RFID to substantially add values to the supply chain operations, especially beyond what the RFID vendors could offer. This paper presents a multi-agent system, incorporating RFID technology, aimed at fulfilling the gap. The system is developed to model supply chain activities (in particular, logistics operations) and is comprised of autonomous and intelligent agents representing the key entities in the supply chain. With the advanced characteristics of RFID incorporated, the agent system examines ways logistics operations (i.e. distribution network) particular) can be efficiently reconfigured and optimised in response to dynamic changes in the market, production and at any stage in the supply chain. © 2012 IEEE.

A linear relational DEA model to evaluate two-stage processes with shared inputs

Two-stage data envelopment analysis (DEA) efficiency models identify the efficient frontier of a two-stage production process. In some two-stage processes, the inputs to the first stage are shared by the second stage, known as shared inputs. This paper proposes a new relational linear DEA model for dealing with measuring the efficiency score of two-stage processes with shared inputs under constant returns-to-scale assumption. Two case studies of banking industry and university operations are taken as two examples to illustrate the potential applications of the proposed approach.