Mg/Ca ratios in planktonic foraminifera

The primary Mg/Ca ratio of foraminiferal shells is a potentially valuable paleoproxy for sea surface temperature (SST) reconstructions. However, the reliable extraction of this ratio from sedimentary calcite assumes that we can overcome artifacts related to foraminiferal ecology and partial dissolution, as well as contamination by secondary calcite and clay. The standard batch method for Mg/Ca analysis involves cracking, sonicating, and rinsing the tests to remove clay, followed by chemical cleaning, and finally acid-digestion and single-point measurement. This laborious procedure often results in substantial loss of sample (typically 30-60%). We find that even the earliest steps of this procedure can fractionate Mg from Ca, thus biasing the result toward a more variable and often anomalously low Mg/Ca ratio. Moreover, the more rigorous the cleaning, the more calcite is lost, and the more likely it becomes that any residual clay that has not been removed by physical cleaning will increase the ratio. These potentially significant sources of error can be overcome with a flow-through (FT) sequential leaching method that makes time- and labor-intensive pretreatments unnecessary. When combined with time-resolved analysis (FT-TRA) flow-through, performed with a gradually increasing and highly regulated acid strength, produces continuous records of Mg, Sr, Al, and Ca concentrations in the leachate sorted by dissolution susceptibility of the reacting material. Flow-through separates secondary calcite from less susceptible biogenic calcite and clay, and further resolves the biogenic component into primary and more resistant fractions. FT-TRA reliably separates secondary calcite (which is not representative of original life habitats) from the more resistant biogenic calcite (the desired signal) and clay (a contaminant of high Mg/Ca, which also contains Al), and further resolves the biogenic component into primary and more resistant fractions that may reflect habitat or other changes during ontogeny. We find that the most susceptible fraction of biogenic calcite in surface dwelling foraminifera gives the most accurate value for SST and therefore best represents primary calcite. Sequential dissolution curves can be used to correct the primary Mg/Ca ratio for clay, if necessary. However, the temporal separation of calcite from clay in FT-TRA is so complete that this correction is typically <=2%, even in clay-rich sediments. Unlike hands-on batch methods, that are difficult to reproduce exactly, flow-through lends itself to automation, providing precise replication of treatment for every sample. Our automated flow-through system can process 22 samples, two system blanks, and 48 mixed standards in <12 hours of unattended operation. FT-TRA thus represents a faster, cheaper, and better way to determine Mg/Ca ratios in foraminiferal calcite.

Concentration profiles in batch fermentation of hydrolyzed lignocellulose

Experimental data was obtained for profiling changes in concentrations of two inhibiting compounds in batch fermentation of a synthesized liquor resembling hydrolyzed lignocellulose, a furan (furfural) and a phenolic compound (vanillin), along with standard fermentation data, i.e. substrate, biomass and ethanol concentrations. The initial inhibitor concentrations and fermentation temperatures in the 18 experiments were varied according to a two-level complete center composite experimental design. Based upon these observed variations in the fermentative behavior, the fermentation kinetics were modeled, as published in the corresponding article, including microbial conversion rates of the inhibitive compounds into their less toxic derivatives.

Experimental data from column and batch samples

The presented thesis was written in the frame of a project called 'seepage water prognosis'. It was funded by the Federal Ministry for Education and Science (BMBF). 41 German institutions among them research institutes of universities, public authorities and engineering companies were financed for three years respectively. The aim was to work out the scientific basis that is needed to carry out a seepage water prognosis (Oberacker und Eberle, 2002). According to the Federal German Soil Protection Act (Federal Bulletin, 1998) a seepage water prognosis is required in order to avoid future soil impacts from the application of recycling products. The participants focused on the development of either methods to determine the source strength of the materials investigated, which is defined as the total mass flow caused by natural leaching or on models to predict the contaminants transport through the underlying soil. Annual meetings of all participants as well as separate meetings of the two subprojects were held. The department of Geosciences in Bremen participated with two subprojects. The aim of the subproject that resulted in this thesis was the development of easily applicable, valid, and generally accepted laboratory methods for the determination of the source strength. In the scope of the second subproject my colleague Veith Becker developed a computer model for the transport prognosis with the source strength as the main input parameter.