Petrophysical investigation on sediment core CRP-3 from the Ross Sea, Antarctica

A suite of petrophysical properties - velocity, resistivity, bulk density, porosity, and matrix density - was measured on 88 core plugs from the CRP-3 drillhole. Core-plug bulk densities were used to recalibrate both whole-core and downhole bulk density logs. Core-plug measurements of matrix density permit conversion of the whole-core and downhole bulk density logs to porosity. Both velocity and formation factor (a normalized measure of resistivity) are strongly correlated with porosity. The velocity/porosity pattern is similar to that for the lower part of CRP-2A and is consistent with the empirical relationship for sandstones. Core-plug and whole-core measurements of P-wave velocity at atmospheric pressure exhibit excellent agreement. Measurements of velocity as a function of pressure indicate a significantly higher velocity sensitivity to pressure than has been observed at CRP-1 and CRP-2A; rebound or presence of microcracks at CRP-3 may be responsible. The percentage difference between velocities at in situ pressures and atmospheric pressures increases downhole from 0% at the seafloor to 9% at the bottom. This pattern can be used to correct whole-core velocity data, measured at atmospheric pressure, to in situ velocities for depth-to-time conversion and associated comparison to the seismic profile across the drillsite

Petrophysical investigations on sediment core CRP-2A from the Ross Sea, Antarctica

A suite of petropysical measurements - velocity versus pressure, bulk density, porosity, matrix density, and magnetic susceptibility -was undertaken on 63 core plugs from CRP-2A. These data are used to calibrate neutron, resistivity, and magnetic susceptibility well logs. Agreement between core-plug magnetic susceptibility measurements and both well-log and whole-core data is excellent. Comparison of core-plug bulk densities with continious well-log density records shows very good agreement. Core-plug measurements of matrix density permit conversion of the well-log and whole-core density records to porosity. Sands and muds exhibit similar downhole compaction patterns, and both patterns are consistent with 250 ± 150 m of exhumation. Pervasive cementation, particularly in the lower half of the core, has affected many CRP-2A petrophysical parameters: (1) fractional porosities are reduced by about 0.05 - 0.10 in the lower part of the hole; (2) velocity and porosity rebound are much smaller than is usually observed for unconsolidated sediments with burial depths similar to CRP-2A; (3) velocities are unusually insensitive to pressure, suggesting that any exhumation-induced microcracks have been scaled subsequently; (4) the velocity/porosity relationship lacks the characteristic signature of exhumation-induced microcracks; (5) the velocity/porosity relationship changes with depth, indicating downhole increase in consolidation; (6) Vp/Vs ratios of the highest-porosity sediments are unusually low, implying enhancement of framework stiffness.

(Table 1) Sample characteristics, test consolidations and calculated elastic parameters of ODP Sites 194-1193 and 194-1196

This study is based on rock mechanical tests of samples from platform carbonate strata to document their petrophysical properties and determine their potential for porosity loss by mechanical compaction. Sixteen core-plug samples, including eleven limestones and five dolostones, from Miocene carbonate platforms on the Marion Plateau, offshore northeast Australia, were tested at vertical effective stress, sigma1', of 0-70 MPa, as lateral strain was kept equal to zero. The samples were deposited as bioclastic facies in platform-top settings having paleo-water depths of <10-90 m. They were variably cemented with low-Mg calcite and five of the samples were dolomitized before burial to present depths of 39-635 m below sea floor with porosities of 8-46%. Ten samples tested under dry conditions had up to 0.22% strain at sigma1' = 50 MPa, whereas six samples tested saturated with brine, under drained conditions, had up to 0.33% strain. The yield strength was reached in five of the plugs. The measured strains show an overall positive correlation with porosity. Vp ranges from 3640 to 5660 m/s and Vs from 1840 to 3530 m/s. Poisson coefficient is 0.20-0.33 and Young's modulus at 30 MPa ranged between 5 and 40 GPa. Water saturated samples had lower shear moduli and slightly higher P- to S-wave velocity ratios. Creep at constant stress was observed only in samples affected by pore collapse, indicating propagation of microcracks. Although deposited as loose carbonate sand and mud, the studied carbonates acquired reef-like petrophysical properties by early calcite and dolomite cementation. The small strains observed experimentally at 50 MPa indicate that little mechanical compaction would occur at deeper burial. However, as these rocks are unlikely to preserve their present high porosities to 4-5 km depth, further porosity loss would proceed mainly by chemical compaction and cementation.