Stress field of basaltic rocks of ODP Hole 127-794C

We carried out an experiment to estimate in-situ stresses at ODP Hole 794C (water depth: 2809 m) from the basaltic core samples by deformation rate analysis (DRA). Site 794 is located at the northern end of the Yamato Basin and 70 km west of the eastern Japan Sea intraplate or interplate convergent zone. Stress previously applied to a rock specimen is identified in the inelastic strain behavior of the specimen under uniaxial compression by the method used. Natural remanent magnetization of the sample was also measured to get a reference for the orientation of the horizontal stresses. The vertical, maximum, and minimum horizontal in-situ stresses estimated at a depth of 582 mbsf are 36.4, 43.1, and 31.2 MPa, respectively. The average of the largest and the least horizontal stresses is nearly equal in value to the vertical stress. This suggests that the site is in the stress field of the strike slip regime at the depth, while the stress field of the reverse fault regime has been estimated from the focal mechanism solutions of the earthquakes whose hypocenters are located near or on the convergent boundary. The directions of the largest and the least horizontal stress are estimated to be northeast-southwest and in northwest-southeast, respectively, in taking account of rotation tectonics of the Japan Sea since its formation. The directions of the largest and the least horizontal stresses are opposite to those determined from the earthquakes. These discrepancies of our results with those from earthquakes may be due mainly to the fact that the site is not in the convergent zone.

Compression and expansion index and void ratio of samples from Lomonosov Ridge and Yermak Plateau

With the coupled use of multibeam swath bathymetry, high-resolution subbottom profiling and sediment coring from icebreakers in the Arctic Ocean, there is a growing awareness of the prevalence of Quaternary ice-grounding events on many of the topographic highs found in present water depths of <1000 m. In some regions, such as the Lomonosov Ridge and Yermak Plateau, overconsolidated sediments sampled through either drilling or coring are found beneath seismically imaged unconformities of glacigenic origin. However, there exists no comprehensive analysis of the geotechnical properties of these sediments, or how their inferred stress state may be related to different glacigenic processes or types of ice-loading. Here we combine geophysical, stratigraphic and geotechnical measurements from the Lomonosov Ridge and Yermak Plateau and discuss the glacial geological implications of overconsolidated sediments. The degree of overconsolidation, determined from measurements of porosity and shear strength, is shown to result from consolidation and/or deformation below grounded ice and, with the exception of a single region on the Lomonosov Ridge, cannot be explained by erosion of overlying sediments. We demonstrate that the amount and depth of porosity loss associated with a middle Quaternary (~ 790-950 thousand years ago - ka) grounding on the Yermak Plateau is compatible with sediment consolidation under an ice sheet or ice rise. Conversely, geotechnical properties of sediments from beneath late Quaternary ice-groundings in both regions, independently dated to Marine Isotope Stage (MIS) 6, indicate a more transient event commensurate with a passing tabular iceberg calved from an ice shelf.

Stress tests of ODP Site 131-808 sediments

Sediments undergoing accretion in trench-forearc systems are subjected to conditions of large lateral thrusting. This stress regime controls the mechanism of faulting as well as the yield and strength properties of the sediment. Understanding them is therefore crucial for the construction of quantitative models of sediment dynamics in convergent margin settings. For this purpose triaxial and oedometer tests were performed on six whole-round core samples recovered from Site 808 from depths between 173 and 705 mbsf. Samples from five depth intervals were subjected to a triaxial test program that was primarily designed to define yield and strength behavior. Test specimens were cut parallel and normal to the core axis. Additional five oedometer tests with similarly prepared specimens were performed on samples from four depth intervals to evaluate the directional state and degree of sediment compaction. Test results show that the degree of sediment compaction is higher than expected from overburden. This overcompaction increases with depth. A well-developed mechanical anisotropy is evident in all samples tested, regardless of their depth and lithology. Values of yield limit, stiffness, and shear strength are up to 40% higher in the horizontal direction compared to the vertical direction. In addition the test data demonstrate that the axis of the volumetric yield loci have rotated into extensional stress field. This verifies that the mechanical state of sediment in the accretionary wedge is controlled by in-situ stress conditions of extensional nature. The coefficients of lateral stress inferred suggest that the extensional stress regime becomes increasingly effective with depth.