Glassy objects from DSDP Hole 5-32 in the northeastern Pacific Ocean

Small glassy spheres, ellipsoids, teardrops, cylinders and dumbbells occur in large numbers in Tertiary deep sea clays cored in the northeastern Pacific by the Deep Sea Drilling Project. These objects morphologically resemble microtektites, but have the composition of an oceanic tholeiite. On the basis of their composition and stratigraphic relationship it is considered that they are of volcanic origin and most likely have been formed in deep water by submarine volcanic processes.

Colored dissolved organic matter (cDOM) absorption measurements in terrestrial water objects of Yamal, Yavai and Gydan Peninsula

The datasets present measurements of cDOM absorption in lakes, rivers and streams of Yamal and Gydan Peninsula area during the summer periods from 2012-2014 and 2016. In summer seasons of 2012 - 2013 water samples was collected during "Yamal-Arctic" Expedition. All of the research areas were located near the coastline of Yamal, Yavay, and Gydan Peninsula and Bely Island. In 2012 water samples from rivers, lakes and streams were taken near New Port, Cape Kamenny and Tambey settlements and in basins (water catchments) of the Sabetta, Seyakha, Yuribey (Baydaratskaya Bay, Gydan Peninsula) and Mongocheyakha rivers. In 2013 water samples from rivers, lakes and streams were taken in the Yavai Peninsula, Yayne Vong bay and in the basins (water catchments) of the Sabetta, Mongocheyakha and Yuribey (Gydan Peninsula) rivers. In 2014 lakes were sampled in the Erkuta River basin, south of Yamal Peninsula. In 2016 lakes and rivers were sampled it the Erkuta River basin and Polar Ural area. cDOM is operationally defined by the chosen filter pore size. Samples have been consistently filtrated through 0.7 µm pore size glas fibre filters. cDOM filtrates have been stored in darkness and have been measured after the expedition using the dual-beam Specord200 laboratory spectrometer (Jena Analytik) at the Otto Schmidt Laboratory OSL, Arctic and Antarctic Research Institute, St. Petersburg, Russia. The OSL cDOM protocol (Heim and Roessler, 2016) prescribes 3 Absorbance (A) measurements per sample from UV to 750 nm against ultra-pure water. The absorption coefficient, a, is calculated by a = 2.303A/L, where L is the pathlength of the cuvette [m], and the factor 2.303 converts log10 to loge. The output of the calculation is a continuous spectrum of a. The cDOM a spectra are used to determine the exponential slope value for specific wavelength ranges, S by fitting the data between min and max wavelength to an exponential function. We provide cDOM absorption coefficients for the wavelengths 254, 260, 350, 375, 400, 412, 440, 443 nm [1/m] and Slope values for three different UV, VIS, wavelength ranges: 275 to 295 nm, 350 to 400 nm, 300 to 500 nm [1/m]. All data were carried out by scientists from Arctic and Antarctic Research Institute and Saint Petersburg State University of Russia during "Yamal-Arctic" expeditions in 2012-2013, RFBR project No 14-04-10065 in 2014, No 14-05-00787 in 2016.

A stereo-image analysis JAVA software with links to executable and source code

Scientists planning to use underwater stereoscopic image technologies are often faced with numerous problems during the methodological implementations: commercial equipment is too expensive; the setup or calibration is too complex; or the imaging processing (i.e. measuring objects in the stereo-images) is too complicated to be performed without a time-consuming phase of training and evaluation. The present paper addresses some of these problems and describes a workflow for stereoscopic measurements for marine biologists. It also provides instructions on how to assemble an underwater stereo-photographic system with two digital consumer cameras and gives step-by-step guidelines for setting up the hardware. The second part details a software procedure to correct stereo-image pairs for lens distortions, which is especially important when using cameras with non-calibrated optical units. The final part presents a guide to the process of measuring the lengths (or distances) of objects in stereoscopic image pairs. To reveal the applicability and the restrictions of the described systems and to test the effects of different types of camera (a compact camera and an SLR type), experiments were performed to determine the precision and accuracy of two generic stereo-imaging units: a diver-operated system based on two Olympus Mju 1030SW compact cameras and a cable-connected observatory system based on two Canon 1100D SLR cameras. In the simplest setup without any correction for lens distortion, the low-budget Olympus Mju 1030SW system achieved mean accuracy errors (percentage deviation of a measurement from the object's real size) between 10.2 and -7.6% (overall mean value: -0.6%), depending on the size, orientation and distance of the measured object from the camera. With the single lens reflex (SLR) system, very similar values between 10.1% and -3.4% (overall mean value: -1.2%) were observed. Correction of the lens distortion significantly improved the mean accuracy errors of either system. Even more, system precision (spread of the accuracy) improved significantly in both systems. Neither the use of a wide-angle converter nor multiple reassembly of the system had a significant negative effect on the results. The study shows that underwater stereophotography, independent of the system, has a high potential for robust and non-destructive in situ sampling and can be used without prior specialist training.