Sediment grain size and carbon/carbonate at DSDO Leg 55 Holes

CaCO3 content was determined on board ship by the "Karbonat Bomb" technique (Müller and Gastner, 1971). In this simple procedure, a sample is powdered and treated with HCl in a closed cylinder. Any resulting CO2 pressure is proportional to the CaCO3 content of the sample. Application of the calibration factor to the manometer reading (x 100) yields per cent CaCO3. The error can be as low as 1 per cent for sediments high in CaCO3, and in general an accuracy of ±2 to 5 per cent can be obtained.

(Table 1) Percentage of non-opaque heavy minerals, heavy residue, magnetite, and opaque heavy minerals, DSDP Sites 58-445 and 58-446

Heavy-mineral analyses were made for 39 samples, 27 from DSDP Site 445 and 12 from Site 446. About one-fourth of the samples were so loose that they were easily disaggregated in water. The amount of heavy residue and the magnetite content of the heavy fraction were very high, 0.2 to 44 per cent and (on the average) more than 20 per cent, respectively. Among the non-opaque heavy minerals, common hornblende (0 to 80%) and augite (0 to 98%) are most abundant. Pale-green and bluish-green amphiboles (around 10%) and the epidote group (a few to 48%) are next in abundance. Euhedral apatite and biotite and irregularly shaped chromite are not abundant, but are present throughout the sequence. Hacksaw structure is developed in pale-green amphibole and augite. At Site 445, a fair amount of chlorite and a few glauconite(?) grains are present from Core 445-81 downward. The content of common hornblende and opaque minerals also changes from Core 445-81 downward. A geological boundary may exist between Cores 445-77 and 445-81. Source rocks of the sediments at both sites were basaltic volcanic rocks (possibly alkali suite), schists, and ultramafic rocks. The degree of lithification and amount of heavy residue, and the content of magnetite, non-opaque heavy minerals (excluding mafic minerals), and mafic minerals in the cores were compared with Eocene, Oligocene, and Miocene sandstones of southwest Japan. In many respects, the sediments at Sites 445 and 446 are quite different from those of southwest Japan. From the early Eocene to the early Miocene, the area of these sites belonged to a different geologic province than southwest Japan.

(Table 1) Carbon and isotopic composition of organic carbon in sediments from DSDP Leg 56 Holes

We have analyzed inorganic and organic carbons and determined the isotopic composition of both sedimentary organic carbon and inorganic carbon in carbonates contained in sediments recovered from Holes 434, 434A, 434B, 435, and 435A in the landward slope of Japan and from Hole 436 in the oceanic slope of the Japan Trench. Both inorganic and organic carbons were assayed at the P. P. Shirshov Institute of Oceanology, in the same sample, using the Knopp technique and measuring evolved CO2 gravimetrically. Each sample was analyzed twice in parallel. Measurements were of a ±0.05 per cent accuracy and a probability level of 0.95. Carbon isotopic analysis was carried out on a MI-1305 mass spectrometer at the I. M. Gubkin Institute of Petrochemical and Gas Industry and the results presented as dC13 values related to the PDB standard. The procedure for preparing samples for organic carbon isotopic analysis involved (1) drying damp sediments at 60°C; (2) treating samples, while heating, with 10 N HCl to remove carbonate carbon; and (3) evaporating surplus HCl at 60°C. The organic substance was turned to CO2 by oxidizing it in an oxygen atmosphere. To prepare samples for inorganic carbon isotopic analysis we decomposed the carbonates with orthophosphoric acid and refined the gas evolved. The dC13 measurements, including a full cycle of sample preparation, were of a ±0.5 per cent accuracy and a probability level of 0.95.

(Fig 1, page 350) A manganese nodule in the top part of the CHUBASCO station 17 core taken in the Pacific Ocean

The vast extent of pelagic deposits, covering about 70 per cent of the ocean floor, thus about half of the earth, makes them of obvious importance to all Earth Science. All the pelagic (eupelagic) sediments, whether largely of plankton remains or fine inorganic particles, have certain distinctive characteristics to reflect their environment of accumulation. The great segregation of manganese in pelagic sediments presents many problems. It is hypothesized that in the formation of present day nodules a relatively slow accumulation in order to permit deposition of more of the manganese as large nodules, rather than as the disseminated micronodules that are in larger proportion in the Tertiary.

Description and chemical composition of ferromanganese deposits from Trout Lake, northern Wisconsin

Sediments were collected with Eckman and Petersen dredges from the bottom of Trout Lake, northern Wisconsin, at 221 stations. Sampling was done with a spud sampler at 32 stations, and core samples were obtained with a Jenkins and Mortimer and a Twenhofel sampler at 17 stations. The shore and offshore deposits of the shores of Trout Lake and the shores of the islands are described. Megascopic descriptions are given of the samples collected with the Eckman and Petersen dredges. Sediments on bottoms of about 10 meters or deeper are mainly gyttja, or crusts composed of mixtures of organic matter, ferric hydroxide, and some form of manganese oxide. The latter deposits are extensive. Detailed descriptions of some of the samples of sands are given, and generalizations respecting size and distribution are made. Tables showing quartiles, medians, and coefficients of sorting and skewness of the coarse sediments collected from the bottom are given in tables. Mechanical analyses of all fine sediments, mainly gyttja, were not made, as previous experience seems to have demonstrated that results have no sedimentational value. Organic matter of the gyttja was determined and also the percentages of lignin in the organic matter. Core samples are composed almost entirely of fine materials, mainly gyttja, and determinations were made on these samples in the same way as on the samples obtained with the Eckman and Petersen dredges. Studies of the core samples show that the fine sediments usually contain in excess of 90 per cent moisture and there is very little change in the moisture content from top to bottom of cores. A map shows the distribution of the iron and manganese deposits. These deposits were found to contain 10 to 20 per cent of organic matter, 11 to 16 per cent of metallic iron, and 12 to 30 per cent of metallic manganese. No stratification of any kind was found in any of the deep-water sediments of Trout Lake except in the iron and manganese crusts. Absence of stratification is considered to be due to the slow rate of deposition and the mixing of sediments by organisms which dwell in them. The data indicate that the rate of deposition in the deep waters of Trout Lake is of the order of 1 foot in 15,000 years.

Tab. 1 Mole % CO2 and 13C values of CO2 at baseline and at the final monitoring event for the eight observation wells

During CO2 storage operations in mature oilfields or saline aquifers it is desirable to trace the movement of injected CO2 for verification and safety purposes. We demonstrate the successful use of carbon isotope abundance ratios for tracing the movement of CO2 injected at the Cardium CO2 Storage Monitoring project in Alberta between 2005 and 2007. Injected CO2 had a d13C value of -4.6±1.1 per mil that was more than 10 per mil higher than the carbon isotope ratios of casing gas CO2 prior to CO2 injection with average d13C values ranging from -15.9 to -23.5 per mil. After commencement of CO2 injection, d13C values of casing gas CO2 increased in all observation wells towards those of the injected CO2 consistent with a two-source end-member mixing model. At four wells located in a NE-SW trend with respect to the injection wells, breakthrough of injected CO2 was registered chemically (>50 mol % CO2) and isotopically 1-6 months after commencement of CO2 injection resulting in cumulative CO2 fluxes exceeding 100000 m**3 during the observation period. At four other wells, casing gas CO2 contents remained below 5 mol % resulting in low cumulative CO2 fluxes (<2000 m**3) throughout the entire observation period, but carbon isotope ratios indicated contributions between <30 and 80% of injected CO2. Therefore, we conclude that monitoring the movement of CO2 in the injection reservoir with geochemical and isotopic techniques is an effective approach to determine plume expansion and to identify potential preferential flow paths provided that the isotopic composition of injected CO2 is constant and distinct from that of baseline CO2.

(Table 1) Stable isotope data of chemoherm carbonates at Hydrate Ridge on the Cascadia continental margin

Two active chemoherm build-ups growing freely up into the oceanic water column, the Pinnacle and the South East-Knoll Chemoherms, have been discovered at Hydrate Ridge on the Cascadia continental margin. These microbially-mediated carbonate formations rise above the seafloor by several tens of meters and display a pinnacle-shaped morphology with steep flanks. The recovered rocks are pure carbonates dominated by aragonite. Based on fabric and mineralogic composition different varieties of authigenic aragonite can be distinguished. Detailed visual and petrographic investigations unambiguously reveal the involvement of microbes during the formation of the carbonates. The fabric of the cryptocrystalline and fibrous aragonite can be described as thrombolitic. Fossilized microbial filaments in the microcrystalline aragonite indicate the intimate relationship between microbes and carbonates. The strongly 13C-depleted carbon isotope values of the samples (as low as -48.1 per mill PDB) are characteristic of methane as the major carbon source for the carbonate formation. The methane-rich fluids from which the carbonates are precipitated originate most probably from a gas reservoir below the bottom-simulating reflector (BSR) and rise through fault systems. The d18O values of the aragonitic chemoherm carbonates are substantially higher (as high as 5.0 per mill PDB) than the expected equilibrium value for an aragonite forming from ambient seawater (3.5 per mill PDB). As a first approximation this indicates formation from glacial ocean water but other factors are considered as well. A conceptual model is presented for the precipitation of these chemoherm carbonates based on in situ observations and the detailed petrographic investigation of the carbonates. This model explains the function of the consortium of archaea and sulfate-reducing bacteria that grows on the carbonates performing anaerobic oxidation of methane (AOM) and enabling the precipitation of the chemoherms above the seafloor surrounded by oxic seawater. Beggiatoa mats growing on the surface of the chemoherms oxidize the sulfide provided by sulfate-dependent anaerobic oxidation of methane within an oxic environment. The contact between Beggiatoa and the underlying microbial consortium represents the interface between the overlying oxic water column and an anoxic micro-environment where carbonate formation takes place.

Geochemistry of recent sediments from the Indian Ocean

During the International Indian Ocean Expedition (1964/65) sediment cores were taken on six profiles off the western coast of the Indian Subcontinent. These profiles run approximately perpendicular to the coast, from the deep-sea over the continental slope to the continental shelf. Additional samples and cores were taken in a dense pattern in front of the delta of the Indus River. This pattern of sampling covered not only marine sediments, but also river and beach sediments in Pakistan. The marine samples were obtained with piston, gravity and box corers and by a Van Veen grab sampler. The longest piston core is about 5 meters long. 1. Distribution of the elements on the sediment surface The area of maximal carbonate values (aprox. 80-100% CaCO3) essentially coincides with the continental shelf. The highest Sr values were observed largely within this area, but only in the vicinity of the Gulf of Cambay. Mainly the aragonitic coprolites are responsible for those high Sr contents. The Mg contents of the carbonates are comparatively low; surprisingly enough the highest Mg concentrations were also measured in the coprolites. The maximum contents of organic matter (Core) were found along the upper part of the continental slope. They coincide with the highest porosity and water content of the sediments. Frequently the decomposition of organic matter by oxydation is responsible for the measured Corg contents. On the other side the quantity of originally deposited organic material is less important in most cases. The enrichment of the "bauxitophile" elements Fe, Ti, Cr and V in the carbonate- and quartz-free portions of the sediments is essentially due to the influence of coarse terrigenous detritus. For the elements Mn, Ni and Cu (in per cent of the carbonateand quartz-free sediment) a strong enrichment was observed in the deep-sea realm. The strong increase in Mn toward the deep-sea is explained by authigenesis of Mn-Fe-concretions. Mn-nodules form only under oxydizing conditions which obviously are possible only at very low rates of deposition. The Mg, B and, probably also Mn contents in the clay minerals increase with increasing distance from the continent. This can be explained by the higher adsorption of those elements from sea water because of increasing duration of the clay mineral transport. The comparison of median contents of some elements in our deep-sea samples with deep-sea sediments described by TUREKIAN & WEDEPOHL (1961) shows that clear differences in concentration exist only in the case of "bauxitophile" elements Cr and Be. The Cr and Be contents show a clear increase in the Indian Ocean deep-sea samples compared to those described by TUREKIAn & WEDEPOHL (1961) which can obviously be attributed to the enrichment in the lateritic and bauxitic parent rocks. The different behaviour of the elements Fe, Ti and Mn during decomposition of the source rocks, transport to the sea and during oxydizing and reducing conditions in the marine environment can be illustrated by Ti02/Fe and MnO/Fe ratios. The different compositions of the sediments off the Indus Delta and those of the remaining part of the area investigated are characterized by a different distribution of the elements Mn and Ti. 2. Chemical inhomogenities in the sediments Most longer cores show 3 intervals defined by chemical and sedimentological differences. The top-most interval is coarse-grained, the intermedial interval is fine grained and the lower one again somewhat coarser. At the same time it is possible to observe differences from interval to interval in the organogenic and detrital constituents. During the formation of the middle interval different conditions of sedimentation from those active during the previous and subsequent periods have obviously prevailed. Looking more closely at the organogenic constituents it is remarkable that during the formation of the finer interval conditions of a more intensive oxydation have prevailed that was the case before and after: Core decreases, whereas P shows a relative increase. This may be explained by slower sedimentation rate or by a vertical migration of the oxygen rich zone of the sea-water. The modifications of the elements from minerals in detrital portion of the sediments support an explanation ascribing this fact to modifications of the conditions of denudation and transportation which can come about through a climatic change or through tectonic causes. The paleontological investigations have shown (ZOBEL, in press) that in some of the cores the middle stratum of fine sedimentation represents optimal conditions for organic life. This fact suggests also oxydizing conditions during the sedimentation of this interval. In addition to the depositional stratification an oxydation zone characterized by Mn-enrichment can be recognized. The thickness of the oxidation zone decreases towards the coast and thins out along the middle part of the continental slope. At those places, where the oxydation zone is extremely thin, enrichment of Mn has its maximum. This phenomenon can probably be attributed to the migration of Mn taking place in its dissociated form within the sediment under reducing conditions. On the other side this Mn-migration in the sediment does not take place in the deep-sea, where oxydizing conditions prevail. 3. Interstitial waters in the sediments Already at very small core depths, the interstitial waters have undergone a distinct modification compared with the overlying sea water. This distinct modification applies both to total salinity and to the individual ions. As to the beginning of diagenesis the following conclusions can be drawn: a) A strong K-increase occurs already at an early stage. It may be attributable to a diffusion barrier or to an exchange of Mg-ions on the clays. Part of this increase may also originate from the decomposition of K-containing silicates (mica and feldspars). A K-decrease owing to the formation of illite (WEAVER 1967), however, occurs only at much greater sediment depth. b) Because of an organic protective coating, the dissolution of carbonate is delayed in recent organogenic carbonates. At the same time some Ca is probably being adsorbed on clay minerals. Consequently the Ca-content of the interstitial water drops below the Ca-content of the sea water. c) Already at an early stage the Mg adsorption on the clays is completed. The adsorbed Mg is later available for diagenetic mineral formations and transformations.

Pebbles and carbonate nodules Legs 56-57 Holes

At all DSDP Leg 56 drilling sites, exotic pebbles occur commonly, throughout the cores. Chips of carbonate nodules occur only at Site 434 on the lower inner trench wall. Both exotic pebbles and carbonate nodule chips sometimes tend to be concentrated at particular levels of cores. Exotic pebbles are generally well rounded and consist of various rock types, such as dacite, andesite, basalt, tuff, gabbro, granodiorite, metaquartzite, biotite hornfels, lithic wacke, mudstone, etc., of which dacite occurs commonly at all the sites. Almost all pebbles at Site 436 and most at Sites 434 and 435 may have been rafted by ice. Some at the latter sites may have been derived by down-slope slumping. Carbonate nodules consist of microcrystalline dolomite, manganoan calcite, and siderite; CaCO3 content ranges from 22 to 65 per cent. They are also generally characterized by a high content of P2O5. The nodules are commonly rich in diatom remains, some of which indicate that the nodules are autochthonous. Some nodules contain abundant glass shards, with a modal refractive index of 1.499, almost identical to shards in the surrounding mud and ooze. These facts suggest that the carbonate nodules may have been formed diagenetically, in situ. This may throw light on problems of the formation of carbonate nodules in ancient "geosynclinal" sediments. It is also very important to point out that these carbonate nodules were formed within sediment deposited well below the CCD.

Synthesized grounding line and ice shelf mask for Antarctica

Iceberg calving has been assumed to be the dominant cause of mass loss for the Antarctic ice sheet, with previous estimates of the calving flux exceeding 2,000 gigatonnes per year. More recently, the importance of melting by the ocean has been demonstrated close to the grounding line and near the calving front. So far, however, no study has reliably quantified the calving flux and the basal mass balance (the balance between accretion and ablation at the ice-sheet base) for the whole of Antarctica. The distribution of fresh water in the Southern Ocean and its partitioning between the liquid and solid phases is therefore poorly constrained. Here we estimate the mass balance components for all ice shelves in Antarctica, using satellite measurements of calving flux and grounding-line flux, modelled ice-shelf snow accumulation rates and a regional scaling that accounts for unsurveyed areas. We obtain a total calving flux of 1,321 ± 144 gigatonnes per year and a total basal mass balance of -1,454 ± 174 gigatonnes per year. This means that about half of the ice-sheet surface mass gain is lost through oceanic erosion before reaching the ice front, and the calving flux is about 34 per cent less than previous estimates derived from iceberg tracking. In addition, the fraction of mass loss due to basal processes varies from about 10 to 90 per cent between ice shelves. We find a significant positive correlation between basal mass loss and surface elevation change for ice shelves experiencing surface lowering and enhanced discharge. We suggest that basal mass loss is a valuable metric for predicting future ice-shelf vulnerability to oceanic forcing.

(Table 1) Geochemical and geothermometry data from fibrous calcite vein fills in the Dabashan Fold Belt, China

Fibrous calcite veins with organic inclusions have been widely considered as indicators of oil and gas generation and migration under overpressure. Abundant fibrous calcite veins containing organic-bearing inclusions occur in faulted Lower Paleozoic through Triassic hydrocarbon source rocks in the Dabashan Foreland Belt (DBF). d13CPDB and d18OPDB values of the fibrous calcite range from - 4.8 to -1.9 to per mil and - 12.8 to - 8.4 per mil respectively, which is lighter than that of associated carbonate host rocks ranging from - 1.7 to + 3.1 per mil and - 8.7 to - 4.5 per mil. A linear relationship between d13CPDB and d18OPDB indicates that the calcite veins were precipitated from a mixture of basinal and surface fluids. The fibrous calcite contains a variety of inclusions, such as solid bitumen, methane bearing all-liquid inclusions, and vapor-liquid aqueous inclusions. Homogenization temperatures of aqueous inclusions range from 140 to 196° with an average of 179°. Salinities of aqueous inclusions average 9.7 wt% NaCl. Independent temperatures from bitumen reflectance and inclusion phase relationships of aqueous and methane inclusions were used to determine fluid pressures. Results indicate high pressures, elevated above typical lithostatic confining pressure, from 150 to 200 MPa. The elevated salinity and high temperature and pressure conditions of the fibrous calcite veins argue against an origin solely from burial overpressure resulting from clay transformation and dehydration reactions. Instead fluid inclusion P-T data and geochemistry results and regional geology indicate abnormally high pressures during fluid migration. These findings indicate that tectonic stress generated fracture and fault fluid pathways and caused migration of organic bearing fluids from the DBF during the Yanshan orogeny.

40Ar/39Ar ages of boulders drilled at DSDP Hole 57-439

The 40Ar/39Ar stepheating dating method was applied to parts of three boulders recovered at Site 439, DSDP Leg 57. All the samples gave a well-defined isochron. The isochron ages agree with each other within the experimental uncertainties and give a mean value of 21.4 ± 1.0 Ma.

Biometry, isotopic composition and diet of Arctic charr (Salvelinus alpinus) from Lake Aigneau, Northern Quebec

Two modal size groups of sexually mature Arctic charr (Salvelinus alpinus) differing in shape and found at different depths in Lake Aigneau in the Canadian sub-Arctic are described and tested for genetic and ecological differentiation. Forms consisted of a small littoral resident, mean size 21.7 cm, and a large profundal resident, mean size 53.9 cm. Mitochondrial DNA analysis indicated that seven of eight haplotypes were diagnostic for either the littoral or profundal fish, with 66.6% of the variation being found within form groupings. Pairwise tests of microsatellite data indicated significant differences in nine of 12 loci and a significant difference between the forms across all tested loci. Molecular variation was partitioned to 84.1% within and 15.9% between forms and suggestive of either restricted interbreeding over time or different allopatric origins. Stable isotope signatures were also significantly different, with the profundal fish having higher d13C and d15N values than the littoral fish. Overlap and separation, respectively, in the range of form d13C and d15N signatures indicated that carbon was obtained from similar sources, but that forms fed at different trophic levels. Littoral fish relied on aquatic insects, predominantly chironomids. Profundal fish were largely piscivorous, including cannibalism. Predominantly empty stomachs and low per cent nitrogen muscle-tissue composition among profundal fish further indicated that the feeding activity was limited to the winter when ice-cover increases the density of available prey at depth. Results provide evidence of significant differences between the modal groups, with origins in both genetics and ecology.