Consolidation properties and permeability values of sediments from three ODP Leg 205 sites

Vertical permeability and sediment consolidation measurements were taken on seven whole-round drill cores from Sites 1253 (three samples), 1254 (one sample), and 1255 (three samples) drilled during Ocean Drilling Program Leg 205 in the Middle America Trench off of Costa Rica's Pacific Coast. Consolidation behavior including slopes of elastic rebound and virgin compression curves (Cc) was measured by constant rate of strain tests. Permeabilities were determined from flow-through experiments during stepped-load tests and by using coefficient of consolidation (Cv) values continuously while loading. Consolidation curves and the Casagrande method were used to determine maximum preconsolidation stress. Elastic slopes of consolidation curves ranged from 0.097 to 0.158 in pelagic sediments and 0.0075 to 0.018 in hemipelagic sediments. Cc values ranged from 1.225 to 1.427 for pelagic carbonates and 0.504 to 0.826 for hemipelagic clay-rich sediments. In samples consolidated to an axial stress of ~20 MPa, permeabilities determined by flow-through experiments ranged from a low value of 7.66 x 10**-20 m**2 in hemipelagic sediments to a maximum value of 1.03 x 10**-16 m**2 in pelagic sediments. Permeabilities calculated from Cv values in the hemipelagic sediments ranged from 4.81 x 10**-16 to 7.66 x 10**-20 m**2 for porosities 49.9%-26.1%.

Diffusion transport of water in basalts

Studying diffusive transport in porous rocks is of fundamental importance in understanding a variety of geochemical processes including: element transfer, primary mineral dissolution kinetics and precipitation of secondary phases. Here we report new findings on the relationship between diffusive transport and textural characteristics of the pore systems on the example of mid-oceanic ridge basalts having different degree of alteration but very similar bulk pore volume. Diffusion processes in porous basalts were studied in situ using H2O -> D2O exchange experiments. The effective diffusion coefficients of water molecules increase systematically from 5.05*10**-11 to 1.19*10**-10 m**2/s for fresh and moderately altered basalts and from 2.40*10**-11 to 6.72*10**-11 m**2/s for completely altered basalt as temperature increases from 5 to 50 °C. The activation energy of the diffusion process increases from 12.29 ± 0.71 kJ/mol for fresh and moderately altered basalts to 14.3 ± 1.33 kJ/mol for completely altered basalt. The results indicate that neither the bulk porosity nor the degree of alteration can be used as proxies for the efficiency of element transport during MORB-water interaction. The formation of secondary phases that replace primary minerals and fill the pore space in the rock leads to the formation of tiny pores and phases with large specific surface area. These factors might have a dominant control on the transport properties of altered basaltic rocks.

Slope stability analyses based on sediment cores of the Ligurian Margin, Southern France

Submarine slope failures of various types and sizes are common along the tectonic and seismically active Ligurian margin, northwestern Mediterranean Sea, primarily because of seismicity up to ~M6, rapid sediment deposition in the Var fluvial system, and steepness of the continental slope (average 11°). We present geophysical, sedimentological and geotechnical results of two distinct slides in water depth >1,500 m: one located on the flank of the Upper Var Valley called Western Slide (WS), another located at the base of continental slope called Eastern Slide (ES). WS is a superficial slide characterized by a slope angle of ~4.6° and shallow scar (~30 m) whereas ES is a deep-seated slide with a lower slope angle (~3°) and deep scar (~100 m). Both areas mainly comprise clayey silt with intermediate plasticity, low water content (30-75 %) and underconsolidation to strong overconsolidation. Upslope undeformed sediments have low undrained shear strength (0-20 kPa) increasing gradually with depth, whereas an abrupt increase in strength up to 200 kPa occurs at a depth of ~3.6 m in the headwall of WS and ~1.0 m in the headwall of ES. These boundaries are interpreted as earlier failure planes that have been covered by hemipelagite or talus from upslope after landslide emplacement. Infinite slope stability analyses indicate both sites are stable under static conditions; however, slope failure may occur in undrained earthquake condition. Peak earthquake acceleration from 0.09 g on WS and 0.12 g on ES, i.e. M5-5.3 earthquakes on the spot, would be required to induce slope instability. Different failure styles include rapid sedimentation on steep canyon flanks with undercutting causing superficial slides in the west and an earthquake on the adjacent Marcel fault to trigger a deep-seated slide in the east.