Table 2: Firn temperature, ram resistance, mass balance and submergence velo city measurements on Colle Gnifetti

Distributional patterns of glaciological parameters at the Colle Gnifetti core drilling site are described and their interrelationships are brietly discussed. Observations within a stake network established in 1980 furnish information about snow accumulation (short term balance), submergence velocity of ice tlow (long term balance), ram hardness (melt layer stratigraphy), and firn temperature. In addition, a numerical model was used to estimate local variations of available radiant energy. Melt layer formation is considerably more intensive on the south facing parts of the firn saddie where incoming radiation is high. These melt layers seem to effectively protect some of the fallen snow from wind erosion. As a result, balance ist up to one order of magnitude larger on south facing slopes. Heat applied to the surface is therefore positively correlated with balance, whereas the relation between solar radiation and firn temperature is less dear. Distributional patterns of submergence velocity confirm that the observed spatial variability of surface balance is representative for longer time periods and greatly intluences the time scale and the stratigraphy of firn and ice cores from Colle Gnifetti.

Laboratory investigation of flow structure and resistance of high- and low-angle dunes

A prominent control on the flow over subaqueous dunes is the slope of the downstream leeside. While previous work has focused on steep (~30°), asymmetric dunes with permanent flow separation, little is known about dunes with lower lee-slope angles for which flow separation is absent or intermittent. Here, we present a laboratory investigation where we systematically varied the dune lee-slope, holding other geometric parameters and flow hydraulics constant, to explore effects on the turbulent flow field and flow resistance. Three sets of fixed dunes (lee-slopes of 10°, 20° and 30°) were separately installed in a 15 m long and 1 m wide flume and subjected to 0.20 m deep flow. Measurements consisted of high-frequency, vertical profiles collected with a Laser Doppler Velocimeter (LDV). We show that the temporal and spatial occurrence of flow separation decreases with dune lee-slope. Velocity gradients in the dune leeside depict a free shear layer downstream of the 30° dunes and a weaker shear layer closer to the bed for the 20° and 10° dunes. The decrease in velocity gradients leads to lower magnitude of turbulence production for gentle lee-slopes. Aperiodic, strong ejection events dominate the shear layer, but decrease in strength and frequency for low-angle dunes. Flow resistance of dunes decreases with lee-slope; the transition being non-linear. Over the 10°, 20° and 30° dunes, shear stress is 8%, 33% and 90 % greater than a flat bed, respectively. Our results demonstrate that dune lee-slope plays an important, but often ignored role in flow resistance.

Heat flow measurements on METEOR cruise M86/5

Mud volcanoes (MV) are sources of mass and energy, transported from deeper levels of the sediment pile to the surface. Together with fluid and gas, thermal energy is emitted through these structures. Therefore heat flow determination is a sensible tool to detect and quantify the amount of convective flow. In the Gulf of Cadiz several mud volcanoes can be found along major tectonic lines (SWIM faults). We employ geothermal measurements to observe the activity of mud volcanoes and possible leakage at the faults apart from pronounced structures.

(Table 2) Bottom-hole temperature measurements at DSDP Sites 68-501, 69-504, and 69-505

Drilling durin Deep Sea Drilling Project Legs 68, 69, and 70 on the southern limb of the Costa Rica Rift was used to study geothermal processes in the ocean crust. Two areas were drilled. One was a geothermally hot site on 6.2-m.y.-old crust, where topography is smooth, heat flow is close to that predicted by conductive cooling of the lithosphere (200 mWm**-2), and hydrothermal circulation may be sealed within the crust. The other was on 3.9-m.y.-old crust, where rough topography is associated with low heat flow (15 to 50 mWm**-2) and possible open convection of sea water. At both sites, about 250 m of siliceous-calcareous sediments overlies igneous basement. In the hot area, it blankets the topography, whereas in the cold area, basement outcrops still occur. Operations included numerous down-hole experiments in both areas and hydraulic piston coring of a 230-m sediment section in the hot area. Diagenesis of the sediments appears closely related to temperature. At the hot site, chert was found near basement, and the chemistry of pore fluids, sampled from both sediments and basement, is strongly influenced by reactions within the basement. Strong lateral gradients in the composition of pore fluids occur in the sediments. At the cold site, no chert was found, and bacterial processes within the sediment dominated the chemistry of the pore fluids. Basaltic basement in both areas consists mainly of pillow lavas and thin flows, with occasional more massive units. The basalt is relatively magnesian. The degree of alteration is very small in the cold area, but much more extensive in the hot area. Ease of drilling also shows a strong contrast. Basement penetration reached 562 m in the hot area and was halted because of lack of time; at the cold site, 43 m of basement was cored only with difficulty. The most intensive in-hole experiments were conducted in the hot area. Successful runs with the borehole televiewer allowed basement lithology to be determined and showed the presence of more and less fractured zones. Pulse tests using a single borehole packer gave values of basement permeability of about 2 to 40 millidarcies. Numerous temperature logs established a broadly conductive in situ temperature gradient, with temperatures reaching 120°C at 562 m into the basement. However, anomalously low temperatures in the upper part of the hole, which persisted after drilling disturbance had decayed away, showed that cold ocean water was flowing down the hole and into the basement at about 90 m below the base of the sediments, at rates of about 80 to 100 m/hr. The packer records indicate a pressure at this depth of 10 bars below hydrostatic.

Measurements of fracture toughness applying a four-point-bending technique of ice core B34 from Kohnen Station, Dronning Maud Land, Antarctica

The critical fracture toughness is a material parameter describing the resistance of a cracked body to further crack extension. It is an important parameter to simulate and predict the break-up behaviour of ice shelves from calving of single icebergs to the disintegration of entire ice shelves over a wide range of length scales. The fracture toughness values are calculated with equations that are derived from an elastic stress analysis. Additionally, an X-ray computer tomography (CT scanner) was used to identify the density as a function of depth. The critical fracture toughness of 91 Antarctic inland ice samples with densities between 840 to 870 kg/m**3 has been determined by applying a four-point-bending technique on single edge v-notched beam samples. The examined ice core was drilled 70m north of Kohnen Station, Dronnning Maud Land (75°00' S, 00°04' E, 2882 m).