Composition of hydrothermal manganese oxide deposits from Galapagos mounds, DSDP Leg 70, Hole 509B

During DSDP Leg 70, a 1.60 m thick manganese oxide layer was sampled in hole 509B. This deposit is formed of alternating layers of hard plates of pure todorokite, about 2 mm thick, and of a more powdery material deeply impregnated with manganese oxide, about 3 mm thick. A SEM study of the plates and the associated powder shows that the powdery material is a transformation of a pre-existing sediment, while the plates are a direct precipitation from a hydrothermal solution. The uranium series disequilibrium method was used to determine the ages of the plates. They are found to be in good chronological sequence and in accordance with the sedimentation rate of the area (4.9 cm/10^3 years) which implies that they have been formed at the sediment-seawater interface during a pulsed injection of hydrothermal solution. The powder presents systematically an "older age" which is explained by a slowing down of the injection while the normal sediment settles; the older age is due to the 230Th excess of the sediment.

Biogeochemistry of the Darwin Mounds, NE Atlantic

The Darwin Mounds are a series of small (<=5 m high, 75-100 m diameter) sandy features located in the northern Rockall Trough. They provide a habitat for communities of Lophelia pertusa and associated fauna. Suspended particulate organic matter (sPOM) reaching the deep-sea floor, which could potentially fuel this deep-water coral (DWC) ecosystem, was collected during summer 2000. This was relatively "fresh" (i.e. dominated by labile lipids such as polyunsaturated fatty acids) and was derived largely from phytoplankton remains and faecal pellets, with contributions from bacteria and microzooplankton. Labile sPOM components were enriched in the benthic boundary layer (~10 m above bottom (mab)) relative to 150 mab. The action of certain benthic fauna that are exclusively associated with the DWC ecosystem (e.g. echiuran worms) leads to the subduction of fresh organic material into the sediments. The mound surface sediments are enriched in organic carbon, relative to off-mound sites. There is no evidence for hydrocarbon venting at this location.

Elemental and isotopic compositions of metalliferous and pelagic sediments from the Galapagos mounds area, data of DSDP Leg 70

Nontronite, the main metalliferous phase of the Galapagos mounds, occurs at a subsurface depth of ~2-20 m; Mn-oxide material is limited to the upper 2 m of these mounds. The nontronite forms intervals of up to a few metres thickness, consisting essentially of 100% nontronite granules, which alternate with intervals of normal pelagic sediment. The metalliferous phases represent essentially authigenic precipitates, apparently formed in the presence of upwelling basement-derived hydrothermal solutions which dissolved pre-existent pelagic sediment. Electron microprobe analyses of nontronite granules from different core samples indicate that: (1) there is little difference in major-element composition between nontronitic material from varying locations within the mounds; and (2) adjacent granules from a given sample have very similar compositions and are internally homogeneous. This indicates that the granules are composed of a single mineral of essentially constant composition, consistent with relatively uniform conditions of solution Eh and composition during nontronite formation. The Pb-isotopic composition of the nontronite and Mn-oxide sediments indicates that they were formed from solutions which contained variable proportions of basaltic Pb, introduced into pore waters by basement-derived solutions, and of normal-seawater Pb. However, the Sr-isotopic composition of these sediments is essentially indistinguishable from the value for modern seawater. On the basis of 18O/16O ratios, formation temperatures of ~20-30°C have been estimated for the nontronites. By comparison, temperatures of up to 11.5°C at 9 m depth have been directly measured within the mounds and heat flow data suggest present basement-sediment interface temperatures of 15-25°C.