Heavy metal contents in bottom sediments and Fe-Mn nodules and their states in bottom and interstitial waters from the Clarion-Clipperton province

Ultrafiltration with tagged atoms was used to study physicochemical states (dissolved, colloidal, suspended) of Mn, Co, Ni, Zn, and Ce in bottom and interstitial waters collected in two areas of the Pacific Ocean with Fe-Mn nodules of different size, shape, structure and origin in different abundances. Use of filters with pore diameter of 0.05 ?m allowed to identify colloidal forms of the metals in bottom sediments and interstitial waters. It was demonstrated experimentally that differences in physicochemical situation in the studied areas could result in formation of nodules by different mechanisms, producing characteristic differences that were observed.

(Table 1) Percentage of non-opaque heavy minerals, heavy residue, magnetite, and opaque heavy minerals, DSDP Sites 58-445 and 58-446

Heavy-mineral analyses were made for 39 samples, 27 from DSDP Site 445 and 12 from Site 446. About one-fourth of the samples were so loose that they were easily disaggregated in water. The amount of heavy residue and the magnetite content of the heavy fraction were very high, 0.2 to 44 per cent and (on the average) more than 20 per cent, respectively. Among the non-opaque heavy minerals, common hornblende (0 to 80%) and augite (0 to 98%) are most abundant. Pale-green and bluish-green amphiboles (around 10%) and the epidote group (a few to 48%) are next in abundance. Euhedral apatite and biotite and irregularly shaped chromite are not abundant, but are present throughout the sequence. Hacksaw structure is developed in pale-green amphibole and augite. At Site 445, a fair amount of chlorite and a few glauconite(?) grains are present from Core 445-81 downward. The content of common hornblende and opaque minerals also changes from Core 445-81 downward. A geological boundary may exist between Cores 445-77 and 445-81. Source rocks of the sediments at both sites were basaltic volcanic rocks (possibly alkali suite), schists, and ultramafic rocks. The degree of lithification and amount of heavy residue, and the content of magnetite, non-opaque heavy minerals (excluding mafic minerals), and mafic minerals in the cores were compared with Eocene, Oligocene, and Miocene sandstones of southwest Japan. In many respects, the sediments at Sites 445 and 446 are quite different from those of southwest Japan. From the early Eocene to the early Miocene, the area of these sites belonged to a different geologic province than southwest Japan.

Table 1. Mean geochemical values for Baseline (pre-injection) and Monitor-1 (post-injection) samples, and the percent change between the two weighted means

The Weyburn Oil Field, Saskatchewan is the site of a large (5000 tonnes/day of CO2) CO2-EOR injection project By EnCana Corporation. Pre- and post-injection samples (Baseline and Monitor-1, respectively) of produced fluids from approximately 45 vertical wells were taken and chemically analyzed to determine changes in the fluid chemistry and isotope composition between August 2000 and March 2001. After 6 months of CO2 injection, geochemical parameters including pH, [HCO3], [Ca], [Mg], and ?13CO2(g) point to areas in which injected CO2 dissolution and reservoir carbonate mineral dissolution have occurred. Pre-injection fluid compositions suggest that the reservoir brine in the injection area may be capable of storing as much as 100 million tonnes of dissolved CO2. Modeling of water-rock reactions show that clay minerals and feldspar, although volumetrically insignificant, may be capable of acting as pH buffers, allowing injected CO2 to be stored as bicarbonate in the formation water or as newly precipitated carbonate minerals, given favorable reaction kinetics.

Oil viscosity from experiments and model calculations

Five frequently-used models were chosen and evaluated to calculate the viscosity of the mixed oil. Totally twenty mixed oil samples were prepared with different ratios of light to crude oil from different oil wells but the same oil field. The viscosities of the mixtures under the same shear rates of 10 s**-1 were measured using a rotation viscometer at the temperatures ranging from 30°C to 120°C. After comparing all of the experimental data with the corresponding model values, the best one of the five models for this oil field was determined. Using the experimental data, one model with a better accuracy than the existing models was developed to calculate the viscosity of mixed oils. Another model was derived to predict the viscosity of mixed oils at different temperatures and different values of mixing ratio of light to heavy oil.