(Table T1) Porosity and permeability of samples from ODP Leg 180 sites

Woodlark Basin, an area of continental extension, is an ideal location to study the evolution of permeability and the development of overpressures within an active rift basin. In this investigation, we measured sediment permeabilities of cores from Woodlark Basin and used numerical modeling to determine if pore fluid overpressures are likely at the base of the rift basin. Constant-rate flow tests were conducted on cores from Site 1108, located in the rift basin, and Sites 1115 and 1118, located on the northern margin of the basin. Results of the laboratory tests indicated permeabilities that range from 1.5 x 10**-18 to 1 x 10**-16 m**2. Results of the numerical modeling of Site 1108 suggest that overpressures due to sedimentation are unlikely.

(Table 1) Chemical composition of ethmodiscus oozes from the Indian Ocean

This paper synthesizes all known finds of Ethmodiscus ooze in the Eastern Indian Ocean and indicates areas of its occurrence. Accumulation of Ethmodiscus ooze is controlled by water circulation and relief of the ocean floor. Bedding of Ethmodiscus ooze has gradational layering and cyclicity caused by multiple redeposition of diatom tests. The maximum occurrence of Ethmodiscus rex in sediments corresponds to Late Pleistocene.

(Table 1) Petrological description and consolidation properties of ODP Site 186-1150 and Hole 186-1151A

In order to determine the shear parameters of the forearc sedimentary strata drilled during Ocean Drilling Program Leg 186, West Pacific Seismic Network, Japan Trench, eight whole-round samples were selected from different depths in the drilled sections of Sites 1150 and 1151. Whereas Site 1150 lays above the seismically active part of the subduction zone, Site 1151 is situated in an aseismic zone. The aim of the triaxial tests was, apart from determination of the static stress strain behavior of the sediments, to test the hypothesis that the static stress strain parameter could differ for each sites. In order to simulate undrained deformation conditions according to the high clay mineral content of the strata, consolidated undrained shear tests were performed in a triaxial testing setup. Measurements of water content, grain density, organic content, and microtextural investigations under the scanning electron microscope (SEM) accompanied the compression experiments. After the saturation and consolidation stages were completed, failure occurred in the compression stage of the experiments at peak strengths of 280-7278 kPa. The stiffness moduli calculated for each sample from differential stress vs. strain curves show a linear relationship with depth and range between 181 and 5827 kPa. Under the SEM, the artificial fault planes of the tested specimen only show partial alignment of clay minerals because of the high content of microfossils.

Distribution of foraminifera, pre-Pliocene foraminifera and macrofossil debris in sediment core CRP-2 (Table 1)

The stratigraphic distribution, assemblage content, paleoecology and age of foraminifera recovered in fourteen of sixteen samples from the 5.63 m thick CRP-2 (Lithostratigraphic Unit 2.2) are discussed. LSU 2.2 comprises four discrete lithologic beds. The upward sequence is informally referred to as the lower sand bed, diamicton bed, middle sand bed, and upper sand bed and it is surmised that these four units are closely related in time. The lower sand bed (~1.5m), which overlies lower Miocene sediments and from which it is separated by the Ross Sea Unconformity, contains traces of recycled Miocene diatoms but is otherwise barren of biogenic material. The diamicton bed (~2.42 m) contains 21 species of benthic foraminifera, with assemblages consistently dominated by Cassidulinoides porrectus, Ammoelphidiella antarctica, Rosalina cf. globularis, Cibicides refulgens, and Ehrenbergina glabra. The overlying middle sand bed (~1.9 m) contains 13 species. with C. porrectus and E. glabra dominant and A. antarctica less common than in the underlying diamicton bed. The upper sand bed (~0.46 m) contains four species and very few tests. The diamicton bed and middle sand bed assemblages are considered to be near in situ thanatocoenoses; and sediments interpreted as marine in origin but influenced by hyposaline waters and nearby ice. Planktic taxa are absent, perhaps indicating the presence of tidewater glaciers, sea ice and/or hyposaline surface waters. The small assemblage in the upper sand bed is more problematic and may be recycled. On the basis of foraminifera in the diamicton and middle sand beds. LSU 2.2 is assigned to the Pliocene. The overlying diamicton in LSU 2.1 contains abundant Quaternary foraminifera.

(Table T1) Age determination of seven ODP Leg 201 sites

As part of a wider paleoclimate and paleoceanographic study of Holocene-upper Pleistocene laminated sediments from the eastern equatorial Pacific and Peru continental margin, we completed 32 accelerator mass spectrometry (AMS) 14C dates from cores recovered during Ocean Drilling Program (ODP) Leg 201. Sample preparation and measurement were carried out at the ANTARES AMS facility, Australian Nuclear Science and Technology Organisation (ANSTO), in Sydney, Australia (Lawson et al., 2000, doi:10.1016/S0168-583X(00)00276-7; Fink et al., 2004, doi:10.1016/j.nimb.2004.04.025). Although the sediments are predominantly diatomaceous oozes (D'Hondt, Jørgensen, Miller, et al., 2003, doi:10.2973/odp.proc.ir.201.2003), they contain sufficient inorganic (e.g., foraminifer tests and nannofossil plates) and organic (Meister et al., 2005, doi:10.2973/odp.proc.sr.201.105.2005) carbon to allow 14C dating. These dates permitted us to reconstruct a history of sediment accumulation over the past 20 k.y., particularly on the Peru continental margin. In this report we present 14C AMS dates and other pertinent data from cores from Sites 1227, 1228, and 1229 collected during Leg 201 at the Peru continental margin.

(Table T3) Vitrinite reflection of samples obtained from ODP Leg 180 sites

Seventy-one samples from Ocean Drilling Program Leg 180 sites were analyzed for vitrinite reflectance and organic type. The objective was to define maximum paleotemperatures across the western Woodlark Basin as a function of depth. The organic matter is of early Pliocene to Holocene age and was recovered from drilled depths of 4.5 to 851.3 meters below seafloor. Organic matter is generally restricted to woody fragments within the sediment, although in a number of fine-grained samples, organic matter is dispersed throughout the sample. Virtually all samples contain vitrinite, part of which may be derived from drifted logs. One sample was found to be barren of organic matter, and two contain only fusinite and semifusinite. Variation of vitrinite reflectance is not systematic with either depth or location, and it appears that formation temperatures have been insufficient to cause an increase in vitrinite reflectance levels. Textural variations within the vitrinite show better correlation with depth. Samples of hypautochthonous peats represent either a terrestrial phase of sedimentation or large peat intraclasts within the section, possibly produced by forest fires in the source areas of the organic matter. The vitrinite and peat-derived samples appear to come from eucalyptus forest settings away from the coastline. Liptinite is not abundant in most of the samples (excluding suberinite associated with woody tissues). Marine liptinite is rare to absent, although many of the samples contain abundant foraminiferal tests. Pyrite is abundant in many of the wood fragments, and some pyritization of woody tissues has taken place.

Distribution of the sand-ascidian Seriocarpa rhizoides in surface sediments of Josephine-Bank, North Atlantic (Table 4)

Seriocarpa rhizoides Diehl 1969 was collected in abundance from the calcareous sand of the Josephine Bank (between Portugal and Madeira) during the "Meteor" seamount cruises in 1967. Attachment in this loose soft substratum is effected by fine anchoring strands of the tests. Two irregular series of small polycarp-like hermaphrodite bodies which are embedded in a connective tissue lie directly below the endostyle, forming a tubular compound gonad, but without common ducts. The intermediate nature of the reproductive system with respect to arrangement and structure increases our knowledge about the polygenetic relations of the stylid-genera. Some of the hitherto known ecological facts point to the presumed "seamounts effect" on this species.

(Table 1) Consolidation test for sediments of ODP Leg 130 sites

Consolidation tests were performed on 19 samples of calcareous ooze from the Ontong Java Plateau, obtained during Ocean Drilling Program Leg 130. Rebound curves from consolidation tests on Ontong Java Plateau samples yield porosity rebounds of 1%-4% for these sediments at equivalent depths up to 1200 mbsf. The exception is a radiolarian-rich sample that has 6% rebound. A rebound correction derived from the porosity rebound vs. depth data has been combined with a correction for pore-water expansion to correct the shipboard laboratory porosity data to in-situ values. Comparison of the laboratory porosity data corrected in this manner with the downhole log data shows good agreement.

Relative abundance of pennate diatoms Thalassionema spp. and Thalassiothrix spp. im Upper Miocene-Lower Pliocene bulk sediment at ODP Hole 145-886B, North Pacific (Table 1)

Rapidly deposited Thalassionema-Thalassiothrti pennate diatom oozes previously have been described in Upper Miocene-Lower Pliocene sediment beneath the frontal boundary of the eastern equatorial Pacific. Here we document a new occurrence of Thalassionema-Thalassiothrix ooze in Upper Miocene-Lower Pliocene sediment beneath the frontal boundary of the subarctic North Pacific. The ooze is a 6 m interval of siliceous sediment at Ocean Drilling Program (ODP) sites 885/886 that was rapidly deposited between approximately 5.0 and 5.9 Ma. Bulk sediment in this interval may contain greater than 85% pennate diatom tests. There are also abundant laminae and pockets that are composed entirely of Thalassionema and Thalassiothrix diatoms. The presence of a rapidly deposited ooze dominated by pennate diatoms indicates unusual past conditions in the overlying surface waters. Time coincident deposition of such oozes at two distinct frontal boundary locations of the Pacific suggests that the unusual surface water conditions were causally linked to large-scale oceanographic change. This same oceanographic change most likely involved (1) addition of nutrients to the ocean, or (2) redistribution of nutrients within the ocean. The occurrence and origin of pennate diatom oozes may be a key component to an integrative understanding of late Neogene paleoceanography and biogeochemical cycling.

(Table 1) Summary of basalt unit thickness, vesicularity, number of flow units, and average porosity at ODP Site 135-839

An inflatable drill-string packer was used at Site 839 to measure the bulk in-situ permeability within basalts cored in Hole 839B. The packer was inflated at two depths, 398.2 and 326.9 mbsf; all on-board information indicated that the packer mechanically closed off the borehole, although apparently the packer hydraulically sealed the borehole only at 398.2 mbsf. Two pulse tests were run at each depth, two constant-rate injection tests were run at the first set, and four were run at the second. Of these, only the constant-rate injection tests at the first set yielded a permeability, calculated as ranging from 1 to 5 * 10**-12 m**2. Pulse tests and constant-rate injection tests for the second set did not yield valid data. The measured permeability is an upper limit; if the packer leaked during the experiments, the basalt would be less permeable. In comparison, permeabilities measured at other Deep Sea Drilling Project and Ocean Drilling Program sites in pillow basalts and flows similar to those measured in Hole 839B are mainly about 10**-13 to 10**-14 m**2. Thus, if our results are valid, the basalts at Site 839 are more permeable than ocean-floor basalts investigated elsewhere. Based on other supporting evidence, we consider these results to be a valid measure of the permeability of the basalts. Temperature data and the geochemical and geotechnical properties of the drilled sediments all indicate that the site is strongly affected by fluid flow. The heat flow is very much less than expected in young oceanic basalts, probably a result of rapid fluid circulation through the crust. The geochemistry of pore fluids is similar to that of seawater, indicating seawater flow through the sediments, and sediments are uniformly underconsolidated for their burial depth, again indicating probable fluid flow. The basalts are highly vesicular. However, the vesicularity can only account for part of the average porosity measured on the neutron porosity well log; the remainder of the measured porosity is likely present as voids and fractures within and between thin-bedded basalts. Core samples, together with porosity, density, and resistivity well-log data show locations where the basalt section is thin bedded and probably has from 15% to 35% void and fracture porosity. Thus, the measured permeability seems reasonable with respect to the high measured porosity. Much of the fluid flow at Site 839 could be directed through highly porous and permeable zones within and between the basalt flows and in the sediment layer just above the basalt. Thus, the permeability measurements give an indication of where and how fluid flow may occur within the oceanic crust of the Lau Basin.

87Sr/86Sr ratios of middle Miocene to Pleistocene planktonic foraminifers from ODP Site 117-722 (Table 3)

Continuous magnetostratigraphy and biostratigraphy made it possible to construct a detailed late Neogene record of 87Sr/86Sr isotopic ratios of ocean water, as measured in the tests of planktonic foraminifers. Sediments recovered during Leg 117, in the western Arabian Sea, provide a continuous, high resolution sedimentary record from the early Miocene to present. The late Miocene to Recent is marked by rapidly increasing 87Sr/86Sr ratios in seawater, which results in a chronostratigraphical resolution varying from 0.2 Ma to 1.5 Ma. The 87Sr/86Sr seawater curve has a stepwise character similar to the one determined by DePaolo on Site 590B, in the Tasman Sea, and to the one determined by McKenzie on Site 653A, in the Mediterranean, confirming its use as a chronostratigraphic tool for this time span. Periods of rapid increase in the 87Sr/86Sr isotopic ratio of seawater are correlated with important changes in tectonic and climatic conditions. Experiments showed that bulk carbonate sediment samples have differing 87Sr/86Sr ratios from those of planktonic and benthic foraminifers from the same depth.

(Table 1) Boron concentration and d11B ratios of ODP Hole 130-803D

The pH of the surface ocean is a sensitive function of its alkalinity and total inorganic carbon concentration, properties which also control the partial pressure of atmospheric carbon dioxide (Broecker and Peng, 1982). Thus, an accurate proxy for past ocean pH could yield information about variations in atmospheric CO2. Recently, it has been suggested that the boron isotopic composition of foraminiferal tests depends on the pH of sea water as well as its isotopic composition (Vengosh et al., 1991, doi:10.1016/0016-7037(91)90139-V; Hemming and Hanson, 1992, doi:10.1016/0016-7037(92)90151-8). Here we present boron isotope and elemental data for sedimentary pore fluids and isotope data for bulk foraminiferal samples from a deep-sea sediment core. The composition of the pore waters implies that sea water boron concentrations and isotopic composition have been constant during the past 21 Myr, allowing us to reconstruct past ocean pH directly from the foraminiferal isotope data. We find that 21 Myr ago, surface ocean pH was only 7.4 ±0.2, but it then increased to 8.2 ±0.2 (roughly the present value) about 7.5 Myr ago. This is consistent with suggestions (Popp et al., 1989; Cerling, 1991; Arthur et al., 1991) that atmospheric CO2 concentrations may have been much higher 21 Myr ago than today.