Phytol and phytyldiol concentrations at DYFAMED time series station and sediment trap

Particulate samples from the water column were collected monthly from depths of 5-150 m, between May 1996 and March 1997, in the northwestern Mediterranean Sea (Ligurian Sea) as part of the DYFAMED project within the French JGOFS program. These samples were analyzed by gas chromatography-electron impact mass spectrometry for their phytol and 3-methylidene-3,7,11-trimethylhexadecan-1,2-diol (phytyldiol) content. The corresponding Chlorophyll Phytyl side chain Photodegradation Index, molar ratio of phytyldiol to phytol, was calculated and the mean amount of chlorophyll photodegraded within the euphotic zone estimated. Seasonal differences in the chlorophyll photodegradation process appear in the one-year study. The chlorophyll appeared more photodegraded in the surface water (generally more than 40% photodegraded at 5-10 m) than at the deep chlorophyll maximum (DCM) (40-50 m) observed in the summer stratified waters (about 20% photodegraded). This difference was attributed to the healthy state of the phytoplankton community (coincidence with the highest primary production levels) and to the lower intensity of irradiance at the DCM level. On the other hand, the bulk of the detrital chlorophyll (chlorophyll associated with phytodetritus, phaeopigments) undergoes photodegradation before it sinks out of the photic zone. However, in January (winter mixed water) the pigments exported towards the sea floor were less photodegraded. This is thought to result from a shorter period of residence of the pigments in the photic zone due to vertical convection and grazing activity of macrozooplankton (salps), which are producers of rapid sinking fecal pellets.

Consolidation properties and hydraulic conductivities of sediments from ODP Leg 207 sites

The stress history, permeability, and compressibility of sediments from Demerara Rise recovered during Ocean Drilling Program Leg 207 were determined using one-dimensional incremental load consolidation and low-gradient flow pump permeability tests. Relationships among void ratio, effective stress, and hydraulic conductivity are presented for sampled lithologic units and used to reconstruct effective stress, permeability, and in situ void ratio profiles for a transect of three sites across Demerara Rise. Results confirm that a significant erosional event occurred on the northeastern flank of the rise during the late Miocene, resulting in the removal of ~220 m of upper Oligocene-Miocene deposits. Although Neogene and Paleogene sediments tend to be overconsolidated, Cretaceous sediments are normally consolidated to underconsolidated, suggesting the presence of overpressure. A pronounced drop in permeability occurs at the transition from the Cretaceous black shales into the overlying Maastrichtian-upper Paleocene chalks and clays. The development of a hydraulic seal at this boundary may be responsible for overpressure in the Cretaceous deposits, leading to the lower overconsolidation ratios of these sediments. Coupled with large regional variations in sediment thickness (overburden stresses), the higher permeability overpressured Cretaceous sediments represent a regional lateral fluid conduit on Demerara Rise, possibly venting methane-rich fluids where it outcrops on the margin's northeastern flank.

Flow rates, hydraulic conductivities and permeabilities of sediments from ODP Holes 190-1173A and 190-1174B

Understanding the role of fluids in active accretionary prisms requires quantitative knowledge of parameters such as permeability. We report here the results of permeability tests on four samples from Ocean Drilling Program Leg 190 at the Nankai Trough accretionary prism-two from Site 1173 and two from Site 1174. Volcanic ash is present in one of the samples; otherwise, the material is hemipelagic mud. A constant-rate-of-flow technique was used at various effective pressures and rates of flow. The permeability of the four samples ranges between 10**-15 and 10**-18 m**2, with the ash-bearing sample showing the highest values.

Hydraulic conductivity and experiments of sediment beds

In marine environments, sediments from different sources are stirred and dispersed, generating beds that are composed of mixed and layered sediments of differing grain sizes. Traditional engineering formulations used to predict erosion thresholds are however, generally for unimodal sediment distributions, and so may be inadequate for commonly occurring coastal sediments. We tested the transport behavior of deposited and mixed sediment beds consisting of a simplified two-grain fraction (silt (D50 = 55 µm) and sand (D50 = 300 µm)) in a laboratory-based annular flume with the objective of investigating the parameters controlling the stability of a sediment bed. To mimic recent deposition of particles following large storm events and the longer-term result of the incorporation of fines in coarse sediment, we designed two suites of experiments: (1) "the layering experiment": in which a sandy bed was covered by a thin layer of silt of varying thickness (0.2 - 3 mm; 0.5 - 3.7 wt %, dry weight in a layer 10 cm deep); and (2) "the mixing experiment" where the bed was composed of sand homogeneously mixed with small amounts of silt (0.07 - 0.7 wt %, dry weight). To initiate erosion and to detect a possible stabilizing effect in both settings, we increased the flow speeds in increments up to 0.30 m/s. Results showed that the sediment bed (or the underlying sand bed in the case of the layering experiment) stabilized with increasing silt composition. The increasing sediment stability was defined by a shift of the initial threshold conditions towards higher flow speeds, combined with, in the case of the mixed bed, decreasing erosion rates. Our results show that even extremely low concentrations of silt play a stabilizing role (1.4% silt (wt %) on a layered sediment bed of 10 cm thickness). In the case of a mixed sediment bed, 0.18% silt (wt %, in a sample of 10 cm depth) stabilized the bed. Both cases show that the depositional history of the sediment fractions can change the erosion characteristics of the seabed. These observations are summarized in a conceptual model that suggests that, in addition to the effect on surface roughness, silt stabilizes the sand bed by pore-space plugging and reducing the inflow in the bed, and hence increases the bed stability. Measurements of hydraulic conductivity on similar bed assemblages qualitatively supported this conclusion by showing that silt could decrease the permeability by up to 22% in the case of a layered bed and by up to 70% in the case of a mixed bed.