(Table 1) Chemical composition and bulk densities of dolerites from ODP Hole 504B lower dikes

Chemical interactions between seawater and the oceanic crust have been widely investigated during recent years. However, most of these studies concern the uppermost volcanic part of the crust. The contribution of the underlying sheeted dike complex to the global budget of the oceans is inferred solely from some ophiolite studies and from the 500-m high-level dike section of DSDP/ODP 504B which was drilled in 1981. Hole 504B is the only place where a continuous and long (1260 m) section in the sheeted dike complex has been cored, and it is now regarded as a reference section for the upper oceanic crust. Many petrological and chemical data from these dolerites are available, including the relative proportions of veins, extensively altered adjacent rocks, and less altered 'host-rocks'. For these three reasons, considering the entire dike section penetrated by Hole 504B is a unique chance to study chemical fluxes related to hydrothermal alteration of this part of the oceanic crust. The calculation of any chemical flux implies knowledge of the chemical composition of the fresh precursor (protolith). Previously, mean compositions of glasses (=P1a) or basalts from the Hole 504B volcanics have been used as protoliths. In this paper, we calculate and discuss the use of various protoliths based on dolerites from Hole 504B. We show that the most adequate and realistic protolith is the mean of individual protoliths that we calculated from the acquisition, by automatic mode, of about 1000 microprobe analyses in each thin-section of dolerite from the Hole 504B lower dikes. Consequently, PFm is further used to calculate chemical fluxes in the dike section of Hole 504B. The chemical compositions of the host-rocks adjacent to alteration halos tend to converge to that of PFm with depth, except for Fe2O3t and TiO2. Because the volume percent of alteration halos increases with depth, the total fluxes related to these halos increase with depth. This explains why the mean flux (host-rocks+halos+veins) of the upper dikes is roughly similar to the mean flux of the lower dikes. During the alteration of the entire Hole 504B dike section, the dolerites gained relatively large quantities of Fe2O3t (+4.0 g/100 cm**3) and released much SiO2 (-6.8 g/100 cm**3), CaO (-5.8 g/100 cm**3), and TiO2 (1.6 g/100 cm**3), and minor Al2O3 (-0.7 g/100 cm**3) and MgO (-0.7 g/100 cm**3). We show the importance of the choice of the protolith in the calculation of chemical budget, particularly for elements showing low flux values. In Hole 504B, the Mg uptake by the volcanics during low temperature alteration added to the Mg release by the dikes gives a net flux of -0.07x10**14 g/year. We propose that part of the Mg uptake by the oceanic crust, which is necessary to compensate the rivers input (-1.33x10**14 g/year), occurs in the underlying gabbros and/or in sections which are altered such as Trinity and Troodos ophiolites. Compared with ophiolites, fluxes calculated for elements other than Mg for the entire crust are generally similar (in tendency, if not in absolute value) to that we obtained from Hole 504B.

Mean grain size and structure of ODP Hole 140-504B samples

Microstructural investigations of ocean crust samples provide a complementary approach to both marine surveys and laboratory experiments. The recovery of relatively undeformed diabases from Deep Sea Drilling Project (DSDP)/Ocean Drilling Program (ODP) Hole 504B provides a first opportunity to examine a reference section of microstructural features that influence strain localization at depths of 2 km in the ocean crust. Syn- and post-crystallization features in plagioclase and augite crystals have been examined by optical microscopy and secondary and backscattered electron imaging. These features show a strong influence of modal composition and primary textures on early sites of strain localization. Thermal cracking and subsequent alteration intensities and distribution are strongly phase dependent. A consistently higher intragranular fracture density is observed in augite crystals relative to plagioclase. The impact of alteration on the mechanical response of diabases is likely to depend on the primary textural characteristics. Even where extensive augite alteration occurs, the rock remains supported by a framework of weakly altered plagioclase crystals. The Hole 504B diabases from Leg 140 provide a valuable comparison for future studies of more deformed sections likely to be encountered at depth. Advances in constraining the detailed rheology of the ocean crust at spreading centers would benefit from experimental deformation of texturally diverse diabase and gabbro samples.

(Figure 1) Silicoflagellates at DSDP Hole 69-504

Diverse and abundant late Miocene to Pleistocene silicoflagellates at DSDP Site 504 can be correlated by tropical biostratigraphic zones and relative paleotemperature values to eastern tropical Pacific reference site DSDP 503A farther to the west. Early Pliocene assemblages, which were poorly known until now, are present and can be correlated locally between DSDP Holes 504, 503A, and 495, using species events associated with the new Dictyocha pulchella Subzone and Dictyocha angulata Subzone. Silicoflagellate relative paleotemperature values show major warming at 4.7 to 5.0 Ma (Cores 45-48), 3.4 to 3.8 Ma (Cores 32-33), 1.5 to 1.7 Ma (Cores 12-16), and 0.5 to 0.8 Ma (Cores 3-6). Major coolings occurred at 5.0 to 5.1 Ma (Core 51), 3.9 to 4.4 Ma (Cores 38-44), and 1.0 to 1.3 Ma (Cores 8-10). The appearance of Dictyocha longa is proposed to replace the asperoid/fibuloid ratio reversal as the bottom of the Dictyocha fibula Zone, because the non-evolutionary ratio reverses several times in the upper Miocene of Hole 503A, and at least once in Hole 504. Three new Pliocene silicoflagellates are defined: Dictyocha concinna Bukry, n. sp., D. helix Bukry, n. sp., and D. tamarae Bukry, n. sp.