(Table 1) Composition of organic matter in bottom sediments from the Kuril-Kamchatka Trench

From results of analyses of sediment samples collected on a profile crossing the Kuril-Kamchatka Trench distribution of organic D, N. carbohydrates, lipids and humic substances was established, as well as nature of their relationship with amorphous silica and clay fraction. Sum of the main biochemical groups of organic matter in the surface layer of sediments (0-1 cm) from the Kuril-Kamchatka Trench amounts to about 15%; neogenetic forms not encountered in living organisms make up 85% of organic matter. Among such forms 26% comprise humic substances formed during initial stages of polymerization of decomposition products of biochemical macromolecules.

(Table 1) Magnetic characteristic properties of selected samples of ODP Hole 134-831B

During Ocean Drilling Program Leg 134 (Vanuatu), geological high sensitivity magnetic tools (GHMT) developed by CEA-LETI and TOTAL were used at two drill sites. GHMT combine two sensors, a proton magnetometer for total magnetic field measurements with an operational accuracy of 0.1 nanoteslas (nT), and a highly sensitive induction tool to measure the magnetic susceptibility with an operational accuracy of a few 10**-6 SI units. Hole 829A was drilled through an accretionary prism and the downhole measurements of susceptibility correlate well with other well-log physical properties. Sharp susceptibility contrasts between chalk and volcanic silt sediment provide complementary data that help define the lithostratigraphic units. At Hole 831B magnetic susceptibility and total field measurements were performed through a 700-m reef carbonate sequence of a guyot deposited on top of an andesitic volcano. The downhole magnetic susceptibility is very low and the amplitude of peak-to-peak anomalies is less than a few 10**-5 SI units. Based on the repeatability of the measurements, the accuracy of the magnetic logging measurements was demonstrated to be excellent. Total magnetic field data at Hole 831B reveal low magnetic anomalies of 0.5 to 5 nT and the measurement of a complete repeat section indicates an accuracy of 0.1 to 0.2 nT. Due to the inclination of the earth's magnetic field in this area (~-40°) and the very low magnetic susceptibility of the carbonate, the contribution of the induced magnetization to the total field measured in the hole is negligible. Unfortunately, because the core recovery was extremely poor (<5%) no detailed comparison between the core measurements and the downhole magnetic data could be made. Most samples have a diamagnetic susceptibility and very low intensity of remanent magnetization (< 10**-4 A/m), but a few samples have a stable remanent magnetization up to 0.005 A/m. These variations of the intensity of the remanent magnetization suggest a very heterogeneous distribution of the magnetization in the carbonate sequence that could explain the magnetic field anomalies measured in these weakly magnetized rocks.

(Table 1) Compositional variation with depth in a nodule of sediment sample RVG-10D

A detailed study of a nodule from the Somali Basin dated by 230Thexcess was correlated with the paleoceanographic events recorded in Site 236 (Leg 24) Deep Sea Drilling Project (DSDP) cores. Tentative indications are that the phase of nodule accretion starting with the development of pillar structure at a depth of 20 mm in the nodule around 13 Ma coincides with increased Antarctic Bottom Water (AABW) flow and an elevated calciumcarbonate compensation depth (CCD). The Late Miocene lowering of the CCD is represented by the mottled zones between 8 and 18 mm in the nodule is characterised by an abundant silicate component (>20%) of aeolian origin. The Miocene/Pliocene boundary (5 Ma) occurs at a depth of about 8 mm and is represented by the development of pillar structure and a minimum of aeolian dust (10.3%). The increased biological productivity of the Somali surface water since the Middle Miocene is demonstrated by the increasing Corg content of the nodule (from 0.11 to 0.19%) towards its surface.

(Table 1) Conditions of vertical near-bottom profiling and the main parameters of the benthic boundary layer in several regions of the Black Sea shelf

Measurements of 14 vertical profiles of currents and hydrological parameters in the near-bottom layer with depth resolution of 0.1 m were carried out in several regions of the Black Sea shelf, at five points over the continental slope, and in three deep water regions. The upper boundary of the benthic boundary layer (BBL) was reliably determined at a point at distance from 5-7 to 35-40 m from the bottom where the gradients of density and current velocity changed. Experimental data obtained were used to determine the coefficient of bottom friction, friction velocity, coefficients of vertical diffusion of momentum and density, and vertical fluxes of temperature and salinity in the BBL.

(Table 1) Minor and trace element concentrations in interstitial waters from ODP Leg 166 sites

Concentrations of minor and trace elements (Li, Rb, Sr, Ba, Fe, and Mn) in interstitial water (IW) were found in samples collected during Ocean Drilling Program (ODP) Leg 166 from Sites 1005, 1006, and 1007 on the western flank of the Great Bahama Bank (GBB). Concentrations of Li range from near-seawater values immediately below the sediment/water interface to a maximum of 250 µM deep in Site 1007. Concentrations determined during shore-based studies are substantially lower than the shipboard data presented in the Leg 166 Initial Reports volume (range of 28-439 µM) because of broad-band interferences from high dissolved Sr concentrations in the shipboard analyses. Rubidium concentrations of 1.3-1.7 µM were measured in IW from Site 1006 when salinity was less than 40 psu. A maximum of 2.5 µM is reached downhole at a salinity of 50 psu. Shipboard and shore-based concentrations of Sr2+ are in excellent agreement and vary from 0.15 mM near the sediment water interface to 6.8 mM at depth. The latter represent the highest dissolved Sr2+ concentrations observed to date in sediments cored during the Deep Sea Drilling Project (DSDP) or ODP. Concentrations of Ba2+ span three orders of magnitude (0.1-227µM). Concentrations of Fe (<0.1-14 µM) and Mn (0.1-2 µM) exhibit substantially greater fluctuations than other constituents. The concentrations of minor and trace metals in pore fluids from the GBB transect sites are mediated principally by changes in pore-water properties resulting from early diagenesis of carbonates associated with microbial degradation of organic matter, and by the abundance of detrital materials that serve as a source of these elements. Downcore variations in the abundance of detrital matter reflect differences in carbonate production during various sea-level stands and are more evident at the more proximal Site 1005 than at the more pelagic Site 1006. The more continuous delivery of detrital matter deep in Site 1007 and throughout all of Site 1006 is reflected in a greater propensity to provide trace elements to solution. Concentrations of dissolved Li+ derive principally from (1) release during dissolution of biogenic carbonates and subsequent exclusion during recrystallization and (2) release from partial dissolution of Li-bearing detrital phases, especially ion-exchange reactions with clay minerals. A third but potentially less important source of Li+ is a high-salinity brine hypothesized to exist in Jurassic age (unsampled) sediments underlying those sampled during Leg 166. The source of dissolved Sr2+ is almost exclusively biogenic carbonate, particularly aragonite. Concentrations of dissolved Sr2+ and Ba2+ are mediated by the solubility of their sulfates. Barite and detrital minerals appear to be the more important source of dissolved Ba2+. Concentrations of Fe and Mn2+ in anoxic pore fluids are mediated by the relative insolubility of pyrite and incorporation into diagenetic carbonates. The principal sources of these elements are easily reduced Fe-Mn-rich phases including Fe-rich clays found in lateritic soils and aoelian dust.

(Table 1) Results from XRD analysis as well as sediment type and selected results from ring shear experiments

The location of the seaward tip of a subduction thrust controls material transfer at convergent plate margins, and hence global mass balances. At approximately half of those margins, the material of the subducting plate is completely underthrust so that no accretion or even subduction erosion takes place. Along the remaining margins, material is scraped off the subducting plate and added to the upper plate by frontal accretion. We here examine the physical properties of subducting sediments off Costa Rica and Nankai, type examples for an erosional and an accretionary margin, to investigate which parameters control the level where the frontal thrust cuts into the incoming sediment pile. A series of rotary-shear experiments to measure the frictional strength of the various lithologies entering the two subduction zones were carried out. Results include the following findings: (1) At Costa Rica, clay-rich strata at the top of the incoming succession have the lowest strength (µres = 0.19) while underlying calcareous ooze, chalk and diatomite are strong (up to µres = 0.43; µpeak = 0.56). Hence the entire sediment package is underthrust. (2) Off Japan, clay-rich deposits within the lower Shikoku Basin inventory are weakest (µres = 0.13-0.19) and favour the frontal proto-thrust to migrate into one particular horizon between sandy, competent turbidites below and ash-bearing mud above. (3) Taking in situ data and earlier geotechnical testing into account, it is suggested that mineralogical composition rather than pore-pressure defines the position of the frontal thrust, which locates in the weakest, clay mineral-rich (up to 85 wt.%) materials. (4) Smectite, the dominant clay mineral phase at either margin, shows rate strengthening and stable sliding in the frontal 50 km of the subduction thrust (0.0001-0.1 mm/s, 0.5-25 MPa effective normal stress). (5) Progressive illitization of smectite cannot explain seismogenesis, because illite-rich samples also show velocity strengthening at the conditions tested.

Physical properties of sediment core CRP-1

The relationship between whole-core compressional wave velocities and gamma-ray attenuation porosities of sediments cored at CRP-1 is examined and compared with results from core-plug samples and global models. Both core-plug and whole-core velocities show a strong dependence on porosity: this relationship appears to be independent of lithology. In the range from 0.1 to 0.4 of fractional porosity (Miocene strata), plug velocities are generally 0.2 - 0.5 km s-1 higher than whole-core velocities. Possible reasons include decreased rigidity in the whole core and diagenetic changes in the plugs. Possibly both velocity measurements are correct but neither is fully representative for in situ conditions. It appears that the core-plug results are more compatible with data from other regions than the whole-core data. After removing first-order compaction control from the whole-core porosity record, a second-order control by clay content can be quantified as a simple positive linear regression (R=0.6). In contrast, after correction for first-order control, porosity and velocity are not significantly influenced by lonestone abundance except for rare, very large lonestones.

(Table 1) Grain size composition of surface sediments from the Barents Sea shelf

The surface layer of bottom sediments on the Barents Sea shelf has an irregular but generally very low abundance of diatoms. Tests of species belonging to present-day diatom flora were absent in nearly half of samples; their abundance was only a few shells per gram of dry sediment in 30% of the samples, it was up to 100 shells per gram in 9% of the samples, and was in thousands of shells per gram in only 13% of the samples. The lowest abundances of diatom shells were found in sediments of the eastern and northeastern parts of the sea owing to unfavorable sedimentation conditions and deficiency of dissolved silica in water. But distribution of diatom species on the surface of bottom sediments is strictly consistent with their present-day ranges. About 30% of the samples contained re-deposited Cretaceous and Paleogene diatoms indicating that bottom sediments have largely formed by scouring and re-deposition of underlying material.