Interstitial-water geochemistry of Kerguelen Plateau sediments

This report synthesizes all of the interstitial-water chemistry studies associated with the Kerguelen Plateau phase of ODP Leg 119. Sediments were cored at six sites (49°24'S to 59°36'S) in water depths ranging from 564 to 4082 m. A total of 77 interstitial-water samples was recovered as part of the routine sampling protocol. In addition, a novel, highresolution pore-water sampling program was tested during Leg 119 that enabled us to pinpoint reaction zones and extend our data base to deeper, drier levels that were heretofore inaccessible. Data collected include interstitial-water sodium, potassium, calcium, magnesium, pH, alkalinity, sulfate, ammonia, phosphate, aqueous silica, salinity, chloride, oxidation-reduction potentials, and sediment chemistry. The northern sector (Sites 736 and 737) is characterized by the highest sedimentation rates (up to 140 m/m.y.) and thermal gradients (70°-98°C/km) encountered on the Kerguelen Plateau during Leg 119. Site 737 represents the most reactive sediment column cored on the Kerguelen Plateau. Major cation fluxes at Site 737 are the strongest measured during Leg 119. High dissolved calcium concentrations (141.5 mM) were encountered near the bottom of Hole 737B. Elevated temperatures promote silica diagenesis and the alteration of volcanic material below 300 mbsf, and a diagenetic front was discovered near 370 mbsf at Site 737. The southern portion of the Kerguelen Plateau (Sites 738 and 744) records the lowest sedimentation rates (less than 5 m/m.y.) and thermal gradients (43°C/km) of the three study areas. Major cation fluxes at the southern sites are the lowest that we measured on the Kerguelen Plateau. High-resolution sampling provided evidence for significant silica release to the pore waters during the weathering of basement basalt. The relatively low thermal gradient does not appear to be sufficient for the formation of the opal-CT and quartz chert beds and nodules that were encountered below 120 mbsf at Site 738. Sediment-accumulation rates on the Eastern Kerguelen Sediment Ridge (Sites 745 and 746) are intermediate to those of the northern and southern sites. Deposition below the regional CCD accounts for the nearly carbonate-free, siliceous sediments. Despite their low organic carbon contents (mean = 0.15%), sediments on the Eastern Kerguelen Sediment Ridge exhibit the highest pore-water alkalinity (6.77 mM), ammonium (0.50 mM), and phosphate (23 µM) concentrations measured on the Kerguelen Plateau. Major cation fluxes are intermediate to those calculated for the northern and southern sites. The Eastern Kerguelen Sediment Ridge interstitial waters are unusual, however, in that the downward flux of magnesium is greater than the upward flux of calcium.

Chemical composition of basalts from ODP holes at the Kerguelen Plateau

Petrographic and geochemical study of basalts in the Kerguelen Plateau basement revealed changes in composition and character of volcanism during development of this tectonovolcanic structure. The Kerguelen Plateau is one of the largest intraplate rises in the World Ocean. It started to form about 120 Ma ago. Age of basalts and overlying sediments shows that plateau formation was in the northwest direction. Basalts of the Kerguelen Plateau basement are products of tholeiitic melts in terms of geochemistry, but differ from mid-ocean ridge basalt (MORB). They are enriched in incompatible trace elements and rare earth elements (REE) relative to MORB, and degree of enrichment varies in basalts from different segments of the plateau. Composition of basalts does not directly depend on their age. Specific features of plateau magmatism are commonly explained in terms of a long-living deep magma plume, which variously interacted with a depleted upper mantle source at different stages of plateau formation. However, taking into account block morphology and deep structure of the plateau, one can suggest that plateau volcanism was initiated by a large fault. As the volcanism prograded to the northwest, depth of fault penetration into the mantle changed. Composition of basalts in the plateau basement was also governed by formation depth of primary melts.

Chemistry of gabbroic rocks of ODP Hole 118-735B

We present results of a microprobe investigation of fresh and least-deformed and metamorphosed gabbroic rocks from Leg 118, Hole 735B, drilled on the east side of the Atlantis II Fracture Zone, Southwest Indian Ridge. This rock collection comprises cumulates ranging from troctolites to olivine-gabbro and olivine-gabbronorite to ilmenite-rich ferrogabbros and ferrogabbronorites. As expected, the mineral chemistry is variable and considerably expands the usual oceanic reference spectrum. Olivine, plagioclase, and clinopyroxene are present in all the studied samples. Orthopyroxene and ilmenite, although not rare, are not ubiquitous. Olivine compositions range from Fo85 to Fo30, while plagioclase compositions vary from An70 to An27. Mg/(Mg + Fe2+) of clinopyroxene (mostly diopside to augite) varies from 0.88 to 0.54. Mg/(Mg + Fe2+) of orthopyroxene varies from 0.84 to 0.50. These minerals are not significantly zoned. All mineralogical data indicate that fractional crystallization is an important factor for the formation of cumulates. However, sharp contacts, interpreted as layering boundaries or intrusion margins, suggest polycyclic fractionation of several magma batches of limited volumes. Calculated compositions of magmas in equilibrium with the most magnesian mineral samples at the bottom of the hole represent fractionated liquids through separation of olivine, plagioclase, and clinopyroxene at moderate to low pressures (less than 9 kb). Crystallization of orthopyroxene and ilmenite occurs in the most differentiated liquids. Mixing of magmas having various compositions before entering the cumulate zone is another mechanism necessary to explain extremely differentiated iron-rich gabbros formed in this slow-spreading ridge environment.

Geochemistry of Kerguelen-Heard Plateau basalts

During Leg 120 basalts were recovered at four drill holes on the Kerguelen-Heard Plateau. This paper reports the trace element and Sr, Nd, Hf, and Pb isotopic characteristics of these basalts and compares these basalts with Indian Ocean basalts and Kerguelen and Heard island volcanics. Kerguelen-Heard Plateau basalts are extremely heterogeneous in character. Intersite variations are larger than intrasite variations. Part of the chemical variations of the plateau volcanics overlap with those characteristics of Kerguelen Island volcanics, which indicates tapping of the same mantle source during the two different periods of activity. The estimates of the degree of melting for the plateau basalts (smaller degree of melting than for mid-ocean ridge basalts) and the heterogeneous character of the plateau exclude an origin that requires large degrees of melting or more rigorous convection than at ocean ridges. However, all characteristics indicate an oceanic origin for the Kerguelen-Heard Plateau.

Geochemistry of pore water and sediments from Exmouth Plateau

During Leg 122, a transect was drilled across the Wombat Plateau, a marginal spur of the Exmouth Plateau, complemented by two sites on the Exmouth Plateau proper. In this report, pore-water analyses for major seawater constituents, alkalinity, Ba, Fe, Mn, Li, Sr, Rb, and silica are presented. Large gradients in the pore-water profiles provide evidence of complex sediment/pore-water interactions associated with carbonate and silica diagenesis and the formation of authigenic minerals. Diffusion affects pore-water profiles but differs considerably from site to site. Advection of freshwater, probably of continental origin, helps maintain negative Cl and salinity gradients deep within the sediments of the Exmouth Plateau.

Magnetic petrology of ODP Leg 121 holes

Given the importance of the inversion of seamount magnetic anomalies, particularly to the motion of the Pacific plate, it is important to gain a better understanding of the nature of the magnetic source of these features. Although different in detail, Ninetyeast Ridge is composed of submarine and subaerial igneous rocks that are similar to those found at many seamounts, making it a suitable proxy. We report here on the magnetic petrology of a collection of samples from Ninetyeast Ridge in the Indian Ocean. Our purpose is to determine the relationship between primary petrology, subsequent alteration, and magnetic properties of the recovered rocks. Such information will eventually lead to a more complete understanding of the magnetization of seamounts and presumably improvements in the accuracy of anomaly inversions. Three basement sites were drilled on Ninetyeast Ridge, with recovery of subaerial basalt flows at the first two (Sites 756 and 757) and submarine massive and pillow flows at the final one (Site 758). The three sites were distinctly different. Site 756 was dominated by ilmenite. What titanomagnetite was present had undergone deuteric alteration and secondary hematite was present in many samples. The magnetization was moderate and stable although it yielded a paleolatitude somewhat lower than expected. Site 757 was highly oxidized, presumably while above sea level. It was dominated by primary titanomagnetite, which was deuterically altered. Secondary hematite was common. Magnetization was relatively weak but quite stable. The paleolatitude for all but the lowermost flows was approximately 40° lower than expected. Site 758 was also dominated by primary titanomagnetite. There was relatively little oxidation with most primary titanomagnetite showing no evidence of high-temperature alteration. No secondary hematite was in evidence. This site had the highest magnetization of the three (although somewhat low relative to other seamounts) but was relatively unstable with significant viscous remanence in many samples. Paleolatitude was close to the expected value. It is not possible, at present, to confidently associate these rocks with specific locations in a seamount structure. A possible and highly speculative model would place rocks similar to Site 757 near the top of the edifice, Site 756 lower down but still erupted above sea level, and Site 758 underlying these units, erupted while the seamount was still below sea level.

(Table 1) Sea ice and snow characteristics and heat fluxes observed during R/V Aurora Australis cruise to East Antarctica in September/October 2007

The properties of snow on East Antarctic sea ice off Wilkes Land were examined during the Sea Ice Physics and Ecosystem Experiment (SIPEX) in late winter of 2007, focusing on the interaction with sea ice. This observation includes 11 transect lines for the measurement of ice thickness, freeboard, and snow depth, 50 snow pits on 13 ice floes, and diurnal variation of surface heat flux on three ice floes. The detailed profiling of topography along the transects and the d18O, salinity, and density datasets of snow made it possible to examine the snow-sea-ice interaction quantitatively for the first time in this area. In general, the snow displayed significant heterogeneity in types, thickness (mean: 0.14 +- 0.13 m), and density (325 +- 38 kg/m**3), as reported in other East Antarctic regions. High salinity was confined to the lowest 0.1 m. Salinity and d18O data within this layer revealed that saline water originated from the surface brine of sea ice in 20% of the total sites and from seawater in 80%. From the vertical profiles of snow density, bulk thermal conductivity of snow was estimated as 0.15 W/K/m on average, only half of the value used for numerical sea-ice models. Although the upward heat flux within snow estimated with this value was significantly lower than that within ice, it turned out that a higher value of thermal conductivity (0.3 to 0.4 W/K/m) is preferable for estimating ice growth amount in current numerical models. Diurnal measurements showed that upward conductive heat flux within the snow and net long-wave radiation at the surface seem to play important roles in the formation of snow ice from slush. The detailed surface topography allowed us to compare the air-ice drag coefficients of ice and snow surfaces under neutral conditions, and to examine the possibility of the retrieval of ice thickness distribution from satellite remote sensing. It was found that overall snow cover works to enhance the surface roughness of sea ice rather than moderate it, and increases the drag coefficient by about 10%. As for thickness retrieval, mean ice thickness had a higher correlation with ice surface roughness than mean freeboard or surface elevation, which indicates the potential usefulness of satellite L-band SAR in estimating the ice thickness distribution in the seasonal sea-ice zone.

Primary mineralogy of ODP Leg 115 basalts

Basement rocks were recovered at four sites on Leg 115 along the Reunion hotspot track in the western Indian Ocean. Plate tectonic reconstructions indicate that the drilled structures formed in three different volcanic environments. Sites 706 and 713 from the eastern side of the Saya de Malha Bank and the northern end of the Chagos Bank, respectively, are on a large volcanic platform analogous to Iceland on the Mid-Atlantic Ridge. Lavas at Site 707 on the northwestern side of the Saya de Malha Bank erupted during the early stages of rifting of the Seychelles from India. Basalts from Site 715 were erupted onto an isolated oceanic island that was distant from ocean ridges and continents much as Reunion Island is today. Many of the rocks were examined in thin section and found to be primarily augite-plagioclase basalts with minor olivine and rare opaque oxides. Site 715 is unusual in that it contains a variety of basalts including olivine-rich and aphyric Fe-Ti basalts. At each of the four sites the rocks were grouped into chemical types (units) on the basis of ship- board bulk-rock analyses and at least one thin section from each chemical unit was analyzed by electron microprobe. The plagioclase and augite chemistry reflects the bulk-rock chemistry and, in general, these minerals were in equilibrium with their host magmas at the time the basalts were quenched. Olivine was rarely preserved, but where it is still present it also appears to have crystallized in equilibrium with the host magma. At three of the drill sites plagioclase phenocrysts or megacrysts that crystallized from a primitive magma are also present. The one site (715) that does not contain these primitive plagioclase phenocrysts is also the site that appears to have been influenced the least by ocean- ridge or Deccan-type magmas. Site 715, furthermore, has a mineralogy that is dominated by olivine as compared with the plagioclase-rich lavas of the other sites.

(Table 2) Actual and synthetic mass accumulation rate data and their absolute differences for ODP Site 115-707

Synthetic mass accumulation rates have been calculated for ODP Site 707 using depth-density and depth-porosity functions to estimate values for these parameters with increasing sediment thickness, at 1 Ma time intervals determined on the basis of published microfossil datums. These datums were the basis of the age model used by Peterson and Backman (1990, doi:10.2973/odp.proc.sr.115.163.1990) to calculate actual mass accumulation rate data using density and porosity measurements. A comparison is made between the synthetic and actual mass accumulation rate values for the time interval 37 Ma to the Recent for 1 Myr time intervals. There is a correlation coefficient of 0.993 between the two data sets, with an absolute difference generally less than 0.1 g/cm**2/kyr. We have used the method to extend the mass accumulation rate analysis back to the Late Paleocene (60 Ma) for Site 707. Providing age datums (e.g. fossil or magnetic anomaly data) are available the generation of synthetic mass accumulation rates can be calculated for any sediment sequence.

Isotope geochemistry of Ninetyeast Ridge basalts

The Ninetyeast Ridge lavas have Sr and Nd isotopic ratios intermediate between those of Indian Ocean MORBs and those of the very enriched Kerguelen hot spot. In an Nd-Sr isotope diagram, they also plot close to the fields of St. Paul Island lavas and of the early magmatism on Kerguelen Archipelago. The Ninetyeast Ridge lavas were generated by mixing among at least three components: a depleted, MORB-type component, such as the one erupted today on the Southeast Indian Ridge; a very enriched, high- Sr/ Sr, low-epsilon-Nd, OIB-type component (the Kerguelen hot spot); and an OIB-type component comparable to that sampled from the St. Paul (and Amsterdam) lavas. The Ninetyeast Ridge lavas show a typical Dupal anomaly signature and Pb, Sr, and Nd isotopic systematics indicate that the Kerguelen hot spot was involved in the ridge's formation as the Indian plate moved northward. The different sites cored during ODP Leg 121 show a trend in their isotopic compositions, from less radiogenic Pb/ Pb ratios and intermediate 87Sr/86Sr and 143Nd/**Nd ratios in the oldest lavas (Site 758) toward more radiogenic 206Pb/204Pb, higher epsilon-Nd, and lower 87Sr/86Sr values in the youngest lavas (Site 756). The lavas from Site 757 have 206Pb/204Pb ratios intermediate between those of the lavas from Sites 756 and 758 and higher 87Sr/86Sr and lower epsilon-Nd values. The relative proportions of the hot spot(s) and MORB component have evolved with time, reflecting differences of tectonic setting: the relative proportion of the Kerguelen hot spot component appears lower in the younger Site 756 lavas than in the older lavas from Sites 757 and 758. Site 756 coincides with the beginning of rifting at the Southeast Indian Ridge, about 43 Ma ago. The formation of the early Kerguelen Archipelago lavas may have drained most of the plume-derived material toward the Antarctic plate. Alternatively, the proximity of the spreading-ridge axis may account for the isotopic similarity of the Site 756 lavas to young lavas erupted on the Southeast Indian Ridge, from 33? to 37?S. The older lavas of Ninetyeast Ridge may have formed when the hot spot and ridge axis did not exactly coincide. The involvement of the third component, a St. Paul hot spot, in the genesis of the Ninetyeast Ridge lavas, especially for the Site 756 lavas, is clearly indicated by Sr, Pb, and Nd isotope systematics and also by trace element ratios. These data, together with those from the Kerguelen Plateau, indicate that the Kerguelen hot spot has been active more or less continuously in the South Indian Ocean for at least 115 Ma. This could indicate that the plume, and by inference the Dupal anomaly, is deep seated in origin.

Calcareous nannofossils of ODP Hole 123-765C and DSDP Hole 27-261

Sediments from the Argo Abyssal Plain (AAP), northwest of Australia, are the oldest known from the Indian Ocean and were recovered from ODP Site 765 and DSDP Site 261. New biostratigraphic and sedimentologic data from these sites, as well as reinterpretations of earlier findings, indicate that basal sediments at both localities are of Late Jurassic age and delineate a history of starved sedimentation punctuated by periodic influx of calcareous pelagic turbidites. Biostratigraphy and correlation of Upper Jurassic-Lower Cretaceous sediments is based largely on calcareous nannofossils. Both sites yielded variably preserved nannofossil successions ranging from Tithonian to Hauterivian at Site 765 and Kimmeridgian to Hauterivian at Site 261. The nannofloras are comparable to those present in the European and Atlantic Boreal and Tethyan areas, but display important differences that reflect biogeographic differentiation. The Argo region is thought to have occupied a position at the southern limit of the Tethyan nannofloral realm, thus yielding both Tethyan and Austral biogeographic features. Sedimentary successions at the two sites are grossly similar, and differences largely reflect Site 765's greater proximity to the continental margin. Jurassic sediments were deposited at rates of about 2 m/m.y. near the carbonate compensation depth (CCD) and contain winnowed concentrations of inoceramid prisms and nannofossils, redeposited layers rich in calcispheres and calcisphere debris, manganese nodules, and volcanic detritus. Lower Cretaceous and all younger sediments accumulated below the CCD at rates that were highest (about 20 m/m.y.) during mid-Cretaceous and Neogene time. Background sediment in this interval is noncalcareous claystone; turbidites dominate the sequence and are thicker and coarser grained at Site 765. AAP turbidites consist mostly of calcareous and siliceous biogenic components and volcanogenic smectite clay; they were derived from relatively deep parts of the continental margin that lay below the photic zone, but above the CCD. The Jurassic-Lower Cretaceous section is about the same thickness across the AAP; turbidites in this interval appear to have had multiple sources along the Australian margin. The Upper Cretaceous-Cenozoic section, however, is three times thicker at Site 765 than at Site 261; turbidites in this interval were derived predominantly from the south. Patterns of sedimentation across the AAP have been influenced by shifts in sea level, the CCD, and configuration of the continental margin. Major pulses of calcareous turbidite deposition occurred during Valanginian, Aptian, and Neogene time-all periods of eustatic lowstands and depressed CCD levels. Sediment redeposited on the AAP has come largely from the Australian outer shelf, continental slope, or rise, rather than the continent itself. Most terrigenous detritus was trapped in epicontinental basins that have flanked northwestern Australia since the early Mesozoic.