67 resultados para sampling methods
Resumo:
Samples of zooplankton were collected in the Barents Sea during cruise 11 of R/V Akademik Sergey Vavilov in September-October 1997. Three different sampling methods were used: 30 l bottle, Judey net, and BR net. More than 40 species of zooplankton were revealed. The greatest species diversity occurred in zones of junction of waters of different origin. Within the 100 m upper water layer zooplankton biomass was rather high: aver. 32 g/m**2. The highest biomass was observed in the northeastern part of the region under study and over the shelf of the Russkaya Gavan' Bay. The lowest biomass occurred in the southern part and in the region of the Gusinaya Banka. The average autumn value of zooplankton biomass in the 100 m upper layer (321 mg/m**3) slightly exceeded the multiannual average for the summer period (200 mg/m**3)
Resumo:
We have developed sampling methods and an analytical system to determine the concentration of dissolved organic C (DOC) in marine pore waters. Our analytical approach is a modification of recently developed high-temperature, Pt-catalyzed oxidation methods; it uses Chromatographic trapping of the DOC-derived CO2 followed by reduction to CH4 and flame ionization detection. Sampling experiments with nearshore sediments indicate that pore-water separation by whole-core squeezing causes artificially elevated DOC concentrations, while pore-water recovery by sectioning and centrifugation does not appear to introduce DOC artifacts. Results from a set of northwestern Atlantic continental slope cores suggest that net DOC production accounts for >50% of the organic C that is recycled at the sediment-water interface.
Resumo:
Pore water was collected from each of 10 sites during Ocean Drilling Program (ODP) Leg 168 on the eastern flank of the Juan de Fuca Ridge. These ten sites delineate a transect perpendicular to the present ridge axis and span a crustal age of 0.86-3.59 Ma. At nine of the ten sites the entire sediment section, which ranged from 41.3 to 613.8 m thick, was cored and attempts were made to recover at least one whole round of sediment per section of core for extraction of pore water. Several (2-5) whole-round sediment samples were taken from the uppermost and lowermost cores to constrain the chemical gradient near the sediment/water and sediment/basalt interfaces, respectively. Pore water was extracted from whole-round sediment core sections by squeezing only the most pristine sediment in a titanium squeezer designed by Manheim and Sayles (1974). Two additional water samples were collected in situ using the water-sampler temperature probe (WSTP; Barnes, 1988, doi:10.2973/odp.proc.ir.110.104.1988). Both of these samples were collected in the cased section of the open borehole from ODP Hole 1026B. Formation fluids were flowing up the cased hole into the overlying deep seawater (Fisher et al., 1997, doi:10.1029/97GL01286). Detailed descriptions of the sampling methods that were used to collect fluids are given by the Shipboard Scientific Party (Davis, Fisher, Firth, et al., 1997, doi:10.2973/odp.proc.ir.168.1997).
Resumo:
Pore waters were collected from nine sites during Leg 125 of the Ocean Drilling Program (ODP). The first four sites (778-781) were drilled in the Mariana forearc on and near Conical Seamount, an active serpentine "mud volcano" located about 80 km behind the trench axis and 120 km in front of the active island arc. The last five sites (782-786) were drilled in the Izu-Bonin forearc between the trench and the outer arc high. Pore waters from the five sites from both areas that penetrated serpentine silts (Sites 778,779,780,783, and 784) are discussed in detail by Mottl (this volume). Here we report analyses of the pore waters from all nine sites for Li, Rb, Sr, Ba, Mn, B, and the sulfur isotopic ratio of dissolved sulfate. Sampling methods and results of analyses for major and minor species determined aboard ship were presented by Fryer, Pearce, Stokking, et al. (1990, doi:10.2973/odp.proc.ir.125.1990).