Composition of bottom sediments, rocks, and ores from the Tropical Atlantic

Geological features of some areas of the Tropical Atlantic (stratigraphy, tectonic structure, lithology, distribution of ore components in bottom sediments, petrography of bedrocks, etc.) are under consideration in the book. Regularities of concentration of trace elements in iron-manganese nodules, features of these nodules in bottom sediments, distribution of phosphorite nodules and other phosphorites have been studied. Much attention is paid to rocks of the ocean crust. A wide range of mineralization represented by magnetite, chromite, chalcopyrite, pyrite, pentlandite, and other minerals has been found.

(Table 1) Sediment characteristics at DSDP Hole 75-532A

Orientation and geometry of pores as well as sediment compressibility can be approximated by determining the shrinkage behavior of standardized samples. The sections investigated show that these measurements are influenced by changing sediment composition. This is also well documented by the relationship between void ratio and overburden pressure. Median pore-diameter calculations clearly reflect both sediment composition and compaction.

230Th, 231Pa, and 10Be in particle size fractions of an opal-rich sediment of the Atlantic Southern Ocean

This study centers on the question: How sensitive are 231Pa/230Th and 10Be/230Th to sediment composition and redistribution? The natural radionuclides 231Pa, 230Th and 10Be recorded in deep sea sediments are tracers for water mass advection and particle fluxes. We investigate the influence of oceanic particle composition on the element adsorption in order to improve our understanding of sedimentary isotope records. We present new data on particle size specific 231Pa and 10Be concentrations. An additional separation step, based on settling velocities, led to the isolation of a very opal-rich phase. We find that opal-rich particles contain the highest 231Pa and 10Be concentrations, and higher 231Pa/230Th and 10Be/230Th isotope ratios than opal-poor particles. The fractionation relative to 230Th induced by the adsorption to opal-rich particles is more pronounced for 231Pa than for 10Be. We conclude that bulk 231Pa/230Th in Southern Ocean sediments is most suitable as a proxy for past opal fluxes. The comparison between two neighboring cores with rapid and slow accumulation rates reveals that these isotope ratios are not influenced significantly by the intensity of sediment focusing at these two study sites. However, a simulation shows that particle sorting by selective removal of sediment (winnowing) could change the isotope ratios. Consequently, 231Pa/230Th should not be used as paleocirculation proxy in cases where a strong loss of opal-rich material due to bottom currents occurred.

(Tables 4-5, page 160) REE contents in ferromanganese concretions from the Gulf of Bothnia and the Barents Sea

Ferromanganese concretions from the Svalbard shelf in the Barents Sea show slightly convex shale-normalized REE patterns with no Eu anomalies. Concretions from the Gulf of Bothnia, northern part of the Baltic Sea, exhibit an enrichment of light REE and negative Eu anomalies. This difference is interpreted as a consequence of different conveyor mechanisms of the REE to the sediment. It is suggested that dissolving biogenic debris contributes to the convex pattern obtained in the Barents Sea, whereas an inorganic suspended fraction with scavenged REE is the main carrier in the Gulf of Bothnia. During oxic diagenesis in the sediment, the scavenged REE are set free into the porewater and contribute to the distribution pattern in concretions found in the Gulf of Bothnia. Small Mn-rich spheroidal concretions are enriched two to five times in REE compared to average shale, whereas Mn-poor flat concretions are low in REE. Specific surface area of the concretion and the depth of burial in the oxidized surface sediment are two factors that strongly affect the enrichment of the REE. Weak Ce anomalies are present in the analysed concretions and a redox level dependence is seen.

Physical, Geochemical, Geomechanical, Geophysical and Hydrodynamic Characterization and Anisotropy Assessment of Corvio Sandstone

Corvio sandstone is a ~20 m thick unit (Corvio Formation) that appears in the top section of the Frontada Formation (Campoó Group; Lower Cretaceous) located in Northern Spain in the southern margin of the Basque-Cantabrian Basin. Up to 228 plugs were cored from four 0.3 x 0.2 x 0.5 m blocks of Corvio sandstone, to perform a comprehensive characterization of the physical, mineralogical, geomechanical, geophysical and hydrodynamic properties of this geological formation, and the anisotropic assessment of the most relevant parameters. Here we present the first data set obtained on 53 plugs which covers (i) basic physical and chemical properties including density, porosity, specific surface area and elementary analysis (XRF - CHNS); (ii) the curves obtained during unconfined and confined strengths tests, the tensile strengths, the calculated static elastic moduli and the characteristic stress levels describing the brittle behaviour of the rock; (iii) P- and S-wave velocities (and dynamic elastic moduli) and their respective attenuation factors Qp and Qs, electrical resistivity for a wide range of confining stress; and (iv) permeability and transport tracer tests. Furthermore, the geophysical, permeability and transport tests were additionally performed along the three main orthogonal directions of the original blocks, in order to complete a preliminary anisotropic assessment of the Corvio sandstone.

(Table 1) Composition of bottom sediments from the East Pacific

Adsorption of ion, nickel, cobalt, and manganese from ocean water by calcareous sediments, diatomaceous ooze, hydrogenous sediments, and red clay was studied under close to natural conditions using a tracer method. It was found that hydrogenous sediments selectively remove manganese from seawater. This may be associated with formation of chemical compounds between manganese and sediment material. It was also found that nickel, manganese, and iron exist in the ocean in several ionic and neutral forms. Cobalt typically present in only one ionic form Co(2+).

Chemical composition of oxide-phosphorite pavement from the Blake Plateau under various preparation treatment

Sample preparation technique is critical for valid chemical analyses. A main source of error comes from the fact that the great specific surface area of crusts or nodules enhances their tendency to retain or attract hygroscopic moisture. Variable treatment of this moisture can in extreme cases lead to analytical value differences as great as 40-50 %. In order to quantify these influences, samples of ferromanganese oxide-phosphorite pavement from the Blake Plateau have been subjected to various drying techniques before analysis using X-ray fluorescence.

Experimental data from column and batch samples

The presented thesis was written in the frame of a project called 'seepage water prognosis'. It was funded by the Federal Ministry for Education and Science (BMBF). 41 German institutions among them research institutes of universities, public authorities and engineering companies were financed for three years respectively. The aim was to work out the scientific basis that is needed to carry out a seepage water prognosis (Oberacker und Eberle, 2002). According to the Federal German Soil Protection Act (Federal Bulletin, 1998) a seepage water prognosis is required in order to avoid future soil impacts from the application of recycling products. The participants focused on the development of either methods to determine the source strength of the materials investigated, which is defined as the total mass flow caused by natural leaching or on models to predict the contaminants transport through the underlying soil. Annual meetings of all participants as well as separate meetings of the two subprojects were held. The department of Geosciences in Bremen participated with two subprojects. The aim of the subproject that resulted in this thesis was the development of easily applicable, valid, and generally accepted laboratory methods for the determination of the source strength. In the scope of the second subproject my colleague Veith Becker developed a computer model for the transport prognosis with the source strength as the main input parameter.