Geotechnical engineering characterization of sediments at DSDP Leg 72 Holes

The hydraulic piston coring device (HPC-15) allows recovery of deep ocean sediments with minimal disturbance. The device was used during Leg 72 of the Deep Sea Drilling Project (DSDP) aboard the Glomar Challenger. Core samples were recovered from bore holes in the Rio Grande Rise in the southwest Atlantic Ocean. Relatively undisturbed sediment cores were obtained from Holes 515A, 516, 517, and 518. The results of shipboard physical property measurements and on-shore geotechnical laboratory tests on these cores are presented in this chapter. A limited number of 0.3 m cores were obtained and used in a series of geotechnical tests, including one-dimensional consolidation, direct shear, Atterburg limit, particle size analysis, and specific gravity tests. Throughout the testing program, attention was focused on assessment of sample disturbance associated with the HPC-15 coring device. The HPC-15 device limits sample disturbance reasonably well in terrigenous muds (clays). However, sample disturbance associated with coring calcareous sediments (nannofossil-foraminifer oozes) is severe. The noncohesive, granular behavior of the calcareous sediments is vulnerable to severe disturbance, because of the design of the sampling head on the device at the time of Leg 72. A number of modifications to the sampling head design are recommended and discussed in this chapter. The modifications will improve sample quality for testing purposes and provide longer unbroken core samples by reducing friction between the sediment column and the sampling tool.

Geochemistry and soil characteristics of sediment core GeoB4234

Stable isotopes of sedimentary nitrogen and organic carbon are widely used as proxy variables for biogeochemical parameters and processes in the water column. In order to investigate alterations of the primary isotopic signal by sedimentary diagenetic processes, we determined concentrations and isotopic compositions of inorganic nitrogen (IN), organic nitrogen (ON), total nitrogen (TN), and total organic carbon (TOC) on one short core recovered from sediments of the eastern subtropical Atlantic, between the Canary Islands and the Moroccan coast. Changes with depth in concentration and isotopic composition of the different fractions were related to early diagenetic conditions indicated by pore water concentrations of oxygen, nitrate, and ammonium. Additionally, the nature of the organic matter was investigated by Rock-Eval pyrolysis and microscopic analysis. A decrease in ON during aerobic organic matter degradation is accompanied by an increase of the 15N/14N ratio. Changes in the isotopic composition of ON can be described by Rayleigh fractionation kinetics which are probably related to microbial metabolism. The influence of IN depleted in 15N on the bulk sedimentary (TN) isotope signal increases due to organic matter degradation, compensating partly the isotopic changes in ON. In anoxic sediments, fixation of ammonium between clay lattices results in a decrease of stable nitrogen isotope ratio of IN and TN. Changes in the carbon isotopic composition of TOC have to be explained by Rayleigh fractionation in combination with different remineralization kinetics of organic compounds with different isotopic composition. We have found no evidence for preferential preservation of terrestrial organic carbon. Instead, both TOC and refractory organic carbon are dominated by marine organic matter. Refractory organic carbon is depleted in 13C compared to TOC.

Biomass and bioturbation in surface sediments of the Arctic Ocean

Little is known about the benthic communities of the Arctic Ocean's slope and abyssal plains. Here we report on benthic data collected from box cores along a transect from Alaska to the Barents Abyssal Plain during the Arctic Ocean Section of 1994. We determined: (1) density and biomass of the polychaetes, foraminifera and total infauna; (2) concentrations of potential sources of food (pigment concentration and percent organic carbon) in the sediments; (3) surficial particle mixing depths and rates using downcore 210Pb profiles; and (4) surficial porewater irrigation using NaBr as an inert tracer. Metazoan density and biomass vary by almost three orders of magnitude from the shelf to the deep basins (e.g. 47 403 individuals m**-2 on the Chukchi Shelf to 95 individuals m**-2 in the Barents Abyssal Plain). Water depth is the primary determinant of infaunal density, explaining 39% of the total variability. Potential food concentration varies by almost two orders of magnitude during the late summer season (e.g. the phaeopigment concentration integrated to 10 cm varies from 36.16 mg m**-2 on the Chukchi Shelf to 0.94 mg m**-2 in the Siberia Abyssal Plain) but is not significantly correlated with density or biomass of the metazoa. Most stations show evidence of particle mixing, with mixing limited to <=3 cm below the sediment-water interface, and enhanced pore water irrigation occurs at seven of the nine stations examined. Particle mixing depths may be related to metazoan biomass, while enhanced pore water irrigation (beyond what is expected from diffusion alone) appears to be related to total phaeopigment concentration. The data presented here indicate that Arctic benthic ecosystems are quite variable, but all stations sampled contained infauna and most stations had indications of active processing of the sediment by the associated infauna.

Carbon and Lead chemistry of sediments from the Middle Atlantic Bight

A mass budget was constructed for organic carbon on the upper slope of the Middle Atlantic Bight, a region thought to serve as a depocenter for fine-grained material exported from the adjacent shelf. Various components of the budget are internally consistent, and observed differences can be attributed to natural spatial variability or to the different time scales over which measurements were made. The flux of organic carbon to the sediments in the core of the depocenter zone, at a water depth of 1000 m, was measured with sediment traps to be 65 mg C m**-2 day**-1, of which 6-24 mg C m**-2 day**-1 is buried. Oxygen fluxes into the sediments, measured with incubation chambers attached to a free vehicle lander, correspond to total carbon remineralization rates of 49-70 mg C m**-2 day**-1. Carbon remineralization rates estimated from gradients of Corg within the mixed layer, and from gradients of dissolved ammonia and phosphate in pore waters, sum to only 4-6 mg C m**-2 day**-1. Most of the Corg remineralization in slope sediments is mediated by bacteria and takes place within a few mm of the sediment-water interface. Most of the Corg deposited on the upper slope sediments is supplied by lateral transport from other regions, but even if all of this material were derived from the adjacent shelf, it represents <2% of the mean annual shelf productivity. This value is further lowered by recognizing that as much as half of the Corg deposited on the slope is refractory, having originated by reworking from older deposits. Refractory Corg arrives at the sea bed with an average 14C age 600-900 years older than the pre-bomb 14C age of DIC in seawater, and has a mean life in the sediments with respect to biological remineralization of at least 1000 years. Labile carbon supplied to the slope, on the other hand, is rapidly and (virtually) completely remineralized, with a mean life of < 1 year. Carbon-14 ages of fine-grained carbonate and organic carbon present within the interstices of shelf sands are consistent with this material acting as a source for the old carbon supplied to the slope. Winnowing and export of reworked carbon may contribute to the often-described relationship between organic carbon preservation and accumulation rate of marine sediments.

Pore water and sediment geochemistry of the Bothian Sea

Methane is a powerful greenhouse gas and its biological conversion in marine sediments, largely controlled by anaerobic oxidation of methane (AOM), is a crucial part of the global carbon cycle. However, little is known about the role of iron oxides as an oxidant for AOM. Here we provide the first field evidence for iron-dependent AOM in brackish coastal surface sediments and show that methane produced in Bothnian Sea sediments is oxidized in distinct zones of iron- and sulfate-dependent AOM. At our study site, anthropogenic eutrophication over recent decades has led to an upward migration of the sulfate/methane transition zone in the sediment. Abundant iron oxides and high dissolved ferrous iron indicate iron reduction in the methanogenic sediments below the newly established sulfate/methane transition. Laboratory incubation studies of these sediments strongly suggest that the in situ microbial community is capable of linking methane oxidation to iron oxide reduction. Eutrophication of coastal environments may therefore create geochemical conditions favorable for iron-mediated AOM and thus increase the relevance of iron-dependent methane oxidation in the future. Besides its role in mitigating methane emissions, iron-dependent AOM strongly impacts sedimentary iron cycling and related biogeochemical processes through the reduction of large quantities of iron oxides.

Benthic oxygen flixes on the Washington shelf and slope

Benthic oxygen fluxes calculated from in situ microelectrode profiles arc compared with benthic flux chamber O2 uptake measurements on a transect of eight stations across the continental shelf and three stations on the slope of Washington State. Station depths ranged from 40 to 630 m and bottom-water oxygen concentrations were 127-38 µM. The fluxes measured by the two methods were similar on the slope, but on the shelf, the chamber flux exceeded the microelectrode flux by as much as a factor of 3-4. We attribute this difference to pore-water irrigation, a process which apparently accounts for the oxidation of a significant amount of organic C in the continental shelf sediments. Combining our diffusive flux data with other data demonstrates clearly that the bottomwater oxygen concentration must play some significant role in determining the sedimentary oxygen consumption rate. Numerical simulation of the microelectrode 0, profiles suggests that roughly half the diffusive 0, flux must be consumed within - 1 mm of the sediment surface. If this conclusion is correct, then the magnitude of the diffusive flux depends both on the bottom-water oxygen concentration and on the supply rate of labile C to the sediment surf'ace.

Permeability, overburden stress and friction coefficients of ODP Hole 190-1173A and 190-1174B

Permeability measured on three samples in a triaxial cell under effective confining pressure from 0.2 to 2.5 MPa ranges from 10**-18 to 10**-19 m**2. Overall, results indicate that permeability decreases with effective confining pressure up to 1.5 MPa; however, measurements at low effective pressure are too dispersed to yield a precise general relationship between permeability and pressure. When the effective pressure is increased from 1.5 to 2.5 MPa, permeability is roughly constant (~1-4 x 10**-19 m**2). Samples deformed in the triaxial cell developed slickenlined fractures, and permeability measurements were performed before and after failure. A permeability increase is observed when the sample fails under low effective confining pressure (0.2 MPa), but not under effective pressure corresponding to the overburden stress. Under isotropic stress conditions, permeability decrease related to fracture closure occurs at a relatively high effective pressure of ~1.5 MPa. Coefficients of friction on the fractures formed in the triaxial cell are ~0.4.

Trace metals in sediments of the Var Canyon turbidite system at the DYFAMED station in the Ligurian Sea

The magnitude and the chronology of anthropogenic impregnation by Hg and other trace metals of environmental concern (V, Cr, Ni, Cu, Zn, Ag, Cd and Pb, including its stable isotopes) in the sediments are determined at the DYFAMED station, a site in the Ligurian Sea (Northwestern Mediterranean) chosen for its supposed open-sea characteristics. The DYFAMED site (VD) is located on the right levee of the Var Canyon turbidite system, at the end of the Middle Valley. In order to trace the influence of the gravity current coming from the canyon on trace metal distribution in the sediment, we studied an additional sediment core (VA) from a terrace of the Var Canyon, and material collected in sediment traps at the both sites at 20 m above sea bottom. The patterns of Hg and other trace element distribution profiles are interpreted using stable Pb isotope ratios as proxies for its sources, taking into account the sedimentary context (turbidites, redox conditions, and sedimentation rates). Major element distributions, coupled with the stratigraphic examination of the sediment cores point out the high heterogeneity of the deposits at VA, and major turbiditic events at both sites. At the DYFAMED site, we observed direct anthropogenic influence in the upper sediment layer (<2 cm), while on the Var Canyon site (VA), the anthropization concerns the whole sedimentary column sampled (19 cm). Turbiditic events superimpose their specific signature on trace metal distributions. According to the 210Pbxs-derived sedimentation rate at the DYFAMED site (0.4 mm yr-1), the Hg-enriched layer of the top core corresponds to the sediment accumulation of the last 50 years, which is the period of the highest increase in Hg deposition on a global scale. With the hypothesis of the absence of significant post-depositional redistribution of Hg, the Hg/C-org ratio changes between the surface and below are used to estimate the anthropogenic contribution to the Hg flux accumulated in the sediment. The Hg enrichment, from pre-industrial to the present time is calculated to be around 60%, consistent with estimations of global Hg models. However, based on the chemical composition of the trapped material collected in sediment traps, we calculated that epibenthic mobilization of Hg would reach 73%. Conversely, the Cd/C-org ratio decreases in the upper 5 cm, which may reflect the recent decrease of atmospheric Cd inputs or losses due to diagenetic processes.

Pliocene-Plistocene deposition of carbonate and organic carbon in ODP Hole 159-959C

During Ocean Drilling Program (ODP) Leg 159, four sites (Sites 959-962) were drilled along a depth transect on the Côte d'Ivoire/Ghana Transform Margin. In this study, the Pliocene-Pleistocene history of carbonate and organic carbon accumulation at Hole 959C is reconstructed for the eastern equatorial Atlantic off the Ivory Coast/Ghana based on bulk carbonate, sand fraction, organic carbon, and other organic geochemical records (d13Corg, marine organic matter percentages derived from organic petrology, hydrogen index, C/N). Pliocene-Pleistocene sedimentation off the Ivory Coast/Ghana was strongly affected by low mean sedimentation rates, which are attributed to persistently enhanced bottom-water velocities related to the steep topography of the transform margin. Sand fraction and bulk carbonate records reveal typical glacial/interglacial cycles, preserved, however, with low time resolution. Intermediate carbonate accumulation rates observed throughout the Pliocene-Pleistocene suggest intense winnowing and sediment redistribution superimposed by terrigenous dilution. 'Atlantic-type' sand and carbonate cycles, consistent with records from pelagic areas of the eastern equatorial Atlantic, are encountered at Hole 959C prior to about 0.9 Ma. Total organic carbon (TOC) records are frequently inversely correlated to carbonate contents, indicating mainly productivity-driven carbonate dissolution related to changes in paleoproductivity. During Stages 22-24, 20, 16, 12, 8, and 4, sand and carbonate records reveal a 'Pacific-type' pattern, showing elevated contents during glacials commonly in conjunction with enhanced TOC records. Formation of 'Pacific-type' patterns off the Ivory Coast/Ghana is attributed to drastically increased bottom-water intensities along the transform margin in accordance with results reported from the Walvis Ridge area. Short-term glacial/interglacial changes in paleoproductivity off the Ivory Coast/Ghana are to some extend recognizable during glacials prior to 1.7 Ma and interglacial Stages 21, 19, 13, 9, and 1. Enhanced coastal upwelling during interglacials is attributed to local paleoclimatic and oceanographic conditions off the Ivory Coast/Ghana. Quantitative estimates of marine organic carbon based on organic petrologic and d13Corg records reveal an offset in concentration ranging from 15% to 60%. Highest variabilities of both records are recorded since ~0.9 Ma. Discrepancies between the isotopic and microscopic records are attributed to an admixture of C4 plant debris approaching the eastern equatorial Atlantic via atmospheric dust. Terrestrial organic material likely originated from the grass-savannah-covered Sahel zone in central Africa. Estimated C4 plant concentrations and accumulation rates range from 10% to 37% and from almost zero to 0.006 g/cm**2/k.y., respectively. The strongest eolian supply to the northern Gulf of Guinea is indicated between 1.9 and 1.68 Ma and during glacial isotopic Stages 22-24, 20, 14, and 12. The presence of grass-type plant debris is further supported by organic petrologic studies, which reveal well-preserved cell tissues of vascular plants or tube-shaped, elongated terrestrial macerals showing different levels of oxidation.

Geochemistry, physical properties, diatom abundance and datums of ODP Site 186-1150 and Hole 186-1151A

Detection of climate response to orbital forcing during Cenozoic long-term global cooling is a key to understanding the behavior of Earth's icehouse climate. Sedimentary rhythm, which is a rhythmic or cyclic variation in the sequence of sediments and sedimentary rocks, is useful for quantitative reconstruction of Earth's evolution during geological time. In this study, we attempt to (1) identify sources of natural gamma ray (NGR) emissions of core recovered during Ocean Drilling Program (ODP) Leg 186 by analyses of physical properties, major element concentrations, diatom abundances, and total organic carbon contents, (2) integrate whole-core NGR intensity of recovered core with wireline logging NGR measurements in order to construct a continuous sedimentary sequence, and (3) discuss changes in the NGR signal in the time domain. This attempt gives us preliminary information to discuss climate stability in relation to orbital forcing thorough geologic time. NGR values are obtained mainly by indirectly measuring the amount of terrigenous minerals including potassium and related elements in the sediments. NGR intensity is also affected by high porosity, which in these sediments was related to the amount of diatom valves. NGR signals might be a proxy of the intensity of the East Asian monsoon off Sanriku. A continuous sedimentary record was constructed by integration of the whole-core NGR intensity measured in sediments obtained from the drilled holes with that measured directly in the borehole by wireline logging, then using a stratigraphic age model to convert to a time series covering 1.3-9.7 Ma with a short break at ~5 Ma. High sedimentation rate (H) stages were identified in the sequence, related to intervals of low-amplitude precession and eccentricity variations. The transition of the dominant periodicities through the four H stages may correlate to major shifts in the climate system, including the onset of major Northern Hemisphere glaciation, the initial stage of the East Asian monsoon intensification, and the onset of the East Asian monsoon with uplift of the Himalayas and the Tibetan Plateau.

Physical properties of deep sea sediments

Erstmals quantitativ bearbeitete Rutschungen aus dem Tiefseebereich des äquatorialen Ostatlantiks liegen auf Hängen von 0,4 Grad und 0,7 Grad - das ist sehr viel flacher als die für statische Rutschungsauslösung benötigte kritische Hangneigung (14 Grad bis 16 Grad ). Im Gegensatz zu Flachwassergebieten kann bei Wassertiefen von über 4000 m natürlich der Einfluß von Wellenwirkung und Tidenhub auf die Hangstabilität vernachlässigt werden. Die Sedimentationsraten sind in diesem Bereich zur Bildung eines Porenwasserüberdruckes vielfach zu niedrig. Nach den Hangstabilitätsanalysen bilden hier Erdbeben den wirksamsten Auslösemechanismus für die Rutschungen. Dies gilt auch für Rutschungen an den Kontinentalrändern von Nordwest- und Westafrika sowie für das europäische Nordmeer und für Rutschungen im nördlichen Fidji-Becken. Das Alter der besonders gut datierten Rutschungen vom nordwestafrikanischen Kontinentalrand und der Tiefsee des äquatorialen Ostatlantiks schwankt zwischen 16,000 J.v.h. und 18,000 J.v.h. sowie etwa 130,000 J.v.h.. Es handelt sich dabei um Phasen des Beginns besonders starker Meeresspiegelschwankungen. Ein Vergleich der Meeresspiegelkurve mit dem Alter älterer Rutschungen zeigt ebenfalls eine Parallele mit Zeiten von Regressionen und Transgressionen. Durch die Meeresspiegelschwankungen werden isostatische Vertikalbewegungen des Tiefseebodens von bis zu 30 m bewirkt, die Spannungen in den Lithosphärenplatten erzeugen. Sie allein sind jedoch nicht groß genug, um Brüche in intakten Plattenbereichen zu verursachen. Entlang alter, ehemals aktiver Transform-Bruchzonen (Fracture Zones) können jedoch die aufgebauten Spannungen eher wieder abgebaut werden. Dabei entstehen kleinere Erdstösse und führen zur Auslösung von Rutschungen. Ein Vergleich der Verbreitung von Transform-Störungen und Rutschungen vor Norwegen, Nordwest- und Westafrika sowie vor dem südlichen Afrika zeigt, daß in diesen Gebieten Rutschmassen tatsächlich besonders häufig entlang und in der Verlängerung von Fracture Zones auftreten. Modellrechnungen, die mit typischen Werten für Hangwinkel (0,5 Grad bis 3 Grad) von Tiefseeböschungen und passive Kontinentalränder sowie für häufig ermittelte Scherfestigkeitsgradienten im Sediment (0,5 kPa/m bis 1,7 kPa/m) durchgeführt wurden, ergaben, daß in Gebieten mit normal konsolidierten Sedimenten (ohne Porenwasserüberdruck) nur Erdbeben Rutschungen ausgelöst haben können.

Geochemistry, fluxes and nitrogen isotopic composition data of traps LP1 and EBC2-1 and cores GeoB4242-4 and Geo4301-1

We compare total and biogenic particle fluxes and stable nitrogen isotope ratios (d15N) at three mooring sites along a productivity gradient in the Canary Islands region with surface sediment accumulation rates and sedimentary d15N. Higher particle fluxes and sediment accumulation rates, and lower d15N were observed in the upwelling influenced eastern boundary region (EBC) compared to the oligotrophic sites north of Gran Canaria [European Station for Time-Series in the Ocean, Canary Islands (ESTOC]] and north of La Palma (LP). The impact of organic matter degradation and lateral particle advection on sediment accumulation was quantified with respect to the multi-year flux record at the ESTOC. Remineralisation of organic matter in the water column and at the sediment surface resulted in an organic carbon preservation of about 0.8% and total nitrogen preservation of about 0.4% of the estimated export production. Higher total and carbonate fluxes and accumulation rates in the lower traps and surface sediment compared to the upper traps indicated that at least 50% of the particulate matter at the ESTOC was derived from allochthonous sources. Low d15N values in the lower traps of the ESTOC and LP point to a source region influenced by coastal upwelling. We conclude from this study that the reconstruction of export production or nutrient regimes from sedimentary records in regions with strong productivity gradients might be biased due to the mixture of particles originating from autochthonous and allochthonous sources. This could result in an imprint of high productivity signatures on sedimentation processes in oligotrophic regions.

Measurements of trace metal abundances and isotopes in carbonate sediments, Exuma, Bahamas

In order to validate the use of 238U/235U as a paleoredox proxy in carbonates, we examined the incorporation and early diagenetic evolution of U isotopes in shallow Bahamian carbonate sediments. Our sample set consists of a variety of primary precipitates that represent a range of carbonate producing organisms and components that were important in the past (scleractinian corals, calcareous green and red algae, ooids, and mollusks). In addition, four short push cores were taken in different depositional environments to assess the impact of early diagenesis and pore water chemistry on the U isotopic composition of bulk carbonates. We find that U concentrations are much higher in bulk carbonate sediments (avg. 4.1 ppm) than in primary precipitates (avg. 1.5 ppm). In almost all cases, the lowest bulk sediment U concentrations were as high as or higher than the highest concentrations found in primary precipitates. This is consistent with authigenic accumulation of reduced U(IV) during early diagenesis. The extent of this process appears sensitive to pore water H2S, and thus indirectly to organic matter content. d238/235U values were very close to seawater values in all of the primary precipitates, suggesting that these carbonate components could be used to reconstruct changes in seawater U geochemistry. However, d238/235U of bulk sediments from the push cores was 0.2-0.4 per mil heavier than seawater (and primary precipitates). These results indicate that authigenic accumulation of U under open-system sulfidic pore water conditions commonly found in carbonate sediments strongly affects the bulk U concentrations and 238U/235U ratios. We also report the occurrence of dolomite in a tidal pond core which contains low 234U/238U and 238U/235U ratios and discuss the possibility that the dolomitization process may result in sediments depleted in 238U. From this initial exploration, it is clear that 238U/235U variations in ancient carbonate sediments could be driven by changes in global average seawater, by spatial and temporal variations in the local deposition environment, or subsequent diagenesis. To cope with such effects, proxies for syndepositional pore water redox conditions (e.g., organic matter content, iron speciation, and trace metal distributions) and careful consideration of possible post-deposition alteration will be required to avoid spurious interpretation of 238U/235U data from ancient carbonate sediments.

Physical properties and elastic constants of ODP Holes 137-504B and 140-504B upper crustal rocks

Seismic velocities have been measured at confining pressures of 100 MPa and 600 MPa for sheeted dike samples recovered during Ocean Drilling Program Legs 137 and 140. The compressional- and shear-wave velocities show an increase with depth at Hole 504B, which is in sharp contrast to the atmospheric pressure velocity measurements performed as part of the shipboard analyses. Rocks exposed to different types of alteration and fracture patterns show distinct changes in their physical properties. The seismic reflectors observed on the vertical seismic profile (VSP) experiment performed during Leg 111 may have been caused by low velocity zones resulting from alteration. The amount of fracturing and hydrothermal alteration in several zones also may have contributed to the acoustic impedance contrast necessary to produce the E5 reflector. Poisson's ratios calculated from laboratory velocity measurements show several low values at depths ranging from 1600 mbsf to 2000 mbsf, which tends to follow similar trends obtained from previous oceanic refraction experiments. A comparison of physical properties between samples recovered from Hole 504B and ophiolite studies in the Bay of Islands and Oman shows a good correlation with the Bay of Islands but significant differences from the measurements performed in the Oman complex.

Summary of shipboard physical properties of mudstones, carbonates, and clastic at DSDP Holes 72-515B and 72-516F

Compressional-wave velocity, wet-bulk density, and porosity were measured on sediments and rocks recovered from Deep Sea Drilling Project Holes 515B and 516F. Wet-bulk densities were measured by both gravimetric and GRAPE methods. Velocities were measured on trimmed samples with the Hamilton frame velocimeter. The shipboard measurement techniques are discussed in the explanatory notes chapter (Coulbourn, this volume) and are described in detail by Boyce (1976a). Only the shipboard measurements are reported here.